Sunshower DELUXE WHITE User manual

DELUXE
WHITE / BLACK / ORGANIC GREY
INSTALLATION GUIDE
PART I- PREPARATION
P. 2 P. 1 5 P. 2 8 P. 5 4P. 4 1 SCAN ME!
INSTALLATION
VIDEO

2
DELUXE
WHITE / BLACK / ORGANIC GREY
INSTALLATION GUIDE
PART I- PREPARATION

3
Sunshower B.V.
Hoogoorddreef 63-65
1101 BB Amsterdam
The Netherlands
T [phone]
www.sunshower.eu
[e-mail]
GENERAL INSTRUCTIONS
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
!
!
BE SURE TO READ THIS INSTRUCTION CAREFULLY BEFORE
INSTALLATION. INSTALLATION CAN ONLY BE CARRIED OUT BY
QUALIFIED INSTALLERS. THE ELECTRICAL CONNECTION OF
SUNSHOWER COMPONENTS CAN ONLY BE CARRIED OUT BY
QUALIFIED ELECTRICIANS. SUNSHOWER IS NOT LIABLE FOR
DAMAGE CAUSED BY INCORRECT INSTALLATION.
GENERAL
!
!
THE ELECTRICAL CONNECTION OF SUNSHOWER
COMPONENTS MAY ONLY BE CARRIED OUT BY A QUALIFIED
ELECTRICIAN. THE INSTALLATION AND ELECTRICAL
CONNECTION OF THE SUNSHOWER INSTALLATION MUST
BE CARRIED OUT IN ACCORDANCE WITH THE APPLICABLE
INTERNATIONAL AND NATIONAL STANDARDS AND
GUIDELINES. THE SUNSHOWER MUST BE PROTECTED BY A
SEPARATE EARTH LEAKAGE CIRCUIT BREAKER (RCD) (SEE
ELECTRICAL CONNECTION).
ELECTRICITY

4
DECLARATION OF CONFORMITY
Sunshower B.V., Hoogoorddreef 63-65, 1101 BB Amsterdam (The Netherlands) hereby
declares, under our sole responsibility, that the Sunshower DELUXE is in accordance
with the conditions of the following directives:
• Low-Voltage Directive 2014/35/EU
• Directive 2014/30/EU for Electromagnetic compatibility of the European Parliament
And is in conformity with the following standards:
• EN60335-1:2012 + A11:2014 + AC2014 + A13:2017 + A1:2019
+ A2:2019 + A14:2019
• EN60335-2-27:2014 + A1:2020 + A2:2020
• EN61000-6-3:2007 + A1:2011 + AC:2012
• EN61000-6-1:2007
• EN61000-6-1:2019
• EN61000-3-3:2013
• EN61000-3-2:2014
This Sunshower product is IPX5 approved and specially designed for use and
installation in zone 1.
The Netherlands, Amsterdam, 1 jan 2020
Signed for and on behalf of:
M. Wegdam, Technical Director
Sunshower B.V.
Hoogoorddreef 63-65
1101 BB Amsterdam
The Netherlands
T [phone]
www.sunshower.eu
[e-mail]
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

5
NOT INCLUDED
GLASS PANEL INNER UNIT WALL FRAME GUSSET PLATES +
CONNECTION SLEEVES
PREPARATION
BOX CONTENT
□MS Polymer
□Measuring tape
□Screwdriver ( + )
□Spirit level
□Screws
□Ventilation ducts (round/
rectangular), max. 3 m
□Duct brackets
□Ventilation grilles
□(Non-return valves)
2x
2x
8x
2x
2x
2x
2x
2x
IN THE BOX
□Installation bag
□Gusset plates
□Connection sleeves
□Glasses
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

6
D
E
A
B
C
REQUIRED TOOLS
INSTRUCTIONS
Make the recess in the wall
according to the dimensions shown.
PREPARATION
DIMENSIONS
□Measuring tape
□Spirit level
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
A
B
C
D
E
300 MM
1850 MM
100 MM
450 MM
MIN 165 MM
SEE P9 / P10

7
C B
A
INSTRUCTIONS
Use a YMvK cable of at least 2.5 mm2
and a equipotential bonding cable
of 6 mm2without PVC pipe or 2.5
mm2with PVC pipe. The Sunshower
should be connected to its own
230V~ 50Hz circuit fitted with a
residual current circuit breaker (RCD
30mA) and a 16A fuse.
PREPERATION
ELECTRICITY
500 MM
POWER SUPPLY, 3CORE
CABLE
EQUIPOTENTIAL BONDING
CABLE
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
A
B
C
!
!
ALL ELECTRICAL WORK MUST BE
CARRIED OUT BY A QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH
THE APPLICABLE GUIDELINES (HD
603647701 AND SUCH) AND NATIONAL
REGULATIONS.
A SEPARATE POWER CONNECTION
WITH A SEPARATE FUSE AND A
SEPARATE EARTH LEAKAGE CIRCUIT
BREAKER (RCD) MUST BE PROVIDED.

8
1
2
3
4
A
B
B
-
2
4 3
1
INSTRUCTIONS
NONRETURN VALVES:
Non-return valves must be installed
if the air for your Sunshower is
extracted from a humid area,
e.g. from the outside or from the
bathroom. Please refer to the
image and subsequent pages for
instructions. The non-return valves
can be ordered additionally (as a
set with the glass panels) or can
be purchased separately at your
hardware store.
Examples of humid areas:
bathroom, outside.
Examples of dry areas:
bedroom, hallway, toilet.
GENERAL CONSTRUCTION
GUIDELINES:
• All Sunshower appliances must
be installed with ventilation
ducts
• Ventilation feed and exhaust can
both be a maximum of 3 m
• The space from which/to which
ventilation is provided must be
at least 12 m3
• The ducts can be of any material,
with dimensions Ø100 mm or 110
* 55 mm
• Make as few bends as possible in
the ducts
• The Sunshower may not be
connected to an existing
ventilation system
PREPARATION
VENTILATION
DRY AREA
BATHROOM
OUTSIDE
SHOWER AREA
PAGE 9
PREFERRED
PAGE 10
PAGE 10
 NOT POSSIBLE
ROUND NON
RETURN VALVE
RECTANGULAR
NONRETURN
VALVE
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

9
3
4
5
A1
1
2
3
5
4
A
2
1
6
7
210 MM
100 MM
70 MM
170 MM
8 9
MIN.
MIN.
6
7
8
9
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
INSTALLATION
DRY AREA
INSTRUCTIONS
REQUIRED TOOLS
Install ventilation ducts measuring at
least Ø100 mm or 110 x 54 mm with
a maximum length of 3 m (both feed
and exhaust). The ventilation feed
space must be at least 12 m3.
In this case, non-return valves are
not mandatory.
□Ventilation ducts
□Duct brackets
□Ventilation grilles set (sold
separately)
Ventilation grilles
2x
8x
1x
2x
Feed
Exhaust
Back wall
Optional insulation
Wall construction
(Drywall/Tiles/Hollow
wall)
Minimum inner dimensions (8)
round ducts: 110 mm
Minimum inner dimensions
(8) rectangular ducts: 70 mm
!
!
A

10
1
2
4
6
5
3
A
3
2
1
7
4
5
6
A1
8
910
7
8
9
10
210 MM
100 MM
70 MM
170 MM
MIN.
MIN.
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
REQUIRED TOOLS
□Ventilation ducts
□Duct brackets
□Ventilation grilles set (sold
separately)
Ventilation grilles
Non-return valves
2x
8x
1x
2x
2x
!
!
INSTALLATION
HUMID AREA
INSTRUCTIONS
Install ventilation ducts measuring at
least Ø100 mm or 110 x 54 mm with
a maximum length of 3 m (both feed
and exhaust). The ventilation feed
space must be at least 12 m3.
In this case, non-return valves are
mandatory.
Feed
Exhaust
Non-return valves
Back wall
Optional insulation
Wall construction
(Drywall/Tiles/Hollow
wall)
Minimum inner dimensions (9)
round ducts: 110 mm
Minimum inner dimensions
(9) rectangular ducts: 70 mm
B

11
2
3
1
REQUIRED TOOLS
INSTRUCTIONS
Fold the upper gusset plate as
shown
Fold the lower gusset plate as
shown, depending on the side
where the ventilation supply is
to be installed
Mount both gusset plates at the
top and bottom of the frame
as indicated, using the screws
provided
INSTALLATION
WALL FRAME
□Screwdriver (+)
□Gusset plate
□Screws
2x
8x
1
2
3
TOP
BOTTOM
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N
OR

12
2
1
X2
REQUIRED TOOLS
INSTRUCTIONS
Completely finish the wall before
placing the frame; this gives the best
result. Then install the frame:
Apply sealant to the rear of the
wall frame, around the complete
periphery
Screw the frame to the wall on
both sides
INSTALLATION
WALL FRAME
□Sealant
□Screwdriver (+)
□Screws2x
1
2
!
!
CAUTION:
These instructions are
important to ensure the
IPX5 seal
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

13
A
A
INSTALLATION
WALL FRAME
!
!
Make sure that the frames are
mounted in the wall, instead
of flush with the wall. This is
to guarantee a watertight seal
around the Sunshower.
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

14
INSTRUCTIONS
Attach the connection sleeves to
the gusset plates using the push-in
rivets. Fold the lips of the connection
sleeves back and slide them into the
ventilation ducts.
You have now completed part 1 of
the installation process. Leave the
sealant to dry for 24 hours before
starting part 2.
INSTALLATION
WALL FRAME
REQUIRED TOOLS
□Connection sleeves
□Push-in rivets
2x
8x
INSTALLATION GUIDE DELUXE | PART I | P1071 REV N

15
DELUXE
WHITE / BLACK / ORGANIC GREY
INSTALLATIEHANDLEIDING
DEEL I- VOORBEREIDING

16
Sunshower B.V.
Hoogoorddreef 63-65
1101 BB Amsterdam
Nederland
T [phone]
www.sunshower.eu
[e-mail]
ALGEMENE INSTRUCTIES
!
!
!
!
LEES DEZE INSTRUCTIES ZORGVULDIG DOOR VOORDAT U
MET DE INSTALLATIE BEGINT. INSTALLATIE DIENT ENKEL
UITGEVOERD TE WORDEN DOOR GESCHOOLD EN ERKEND
VAKPERSONEEL. DE ELEKTRISCHE AANSLUITING VAN
SUNSHOWERCOMPONENTEN MAG ALLEEN DOOR EEN
ERKEND ELEKTRICIEN WORDEN UITGEVOERD. SUNSHOWER
IS NIET AANSPRAKELIJK VOOR SCHADE VEROORZAAKT DOOR
ONJUISTE INSTALLATIE.
DE ELEKTRISCHE AANSLUITING VAN SUNSHOWER
COMPONENTEN MAG ALLEEN DOOR EEN ERKEND
ELEKTRICIEN WORDEN UITGEVOERD. DE MONTAGE EN
ELEKTRISCHE AANSLUITING VAN DE SUNSHOWER
INSTALLATIE MOET WORDEN UITGEVOERD IN
OVEREENSTEMMING MET DE GELDENDE INTERNATIONALE
EN NATIONALE NORMEN EN RICHTLIJNEN (BIJVOORBEELD
VOOR NEDERLAND: NEN 1010  701). DE SUNSHOWER
MOET WORDEN BEVEILIGD DOOR EEN APARTE
AARDLEKSCHAKELAAR (RCD) (ZIE ELEKTRISCHE
AANSLUITING).
ALGEMEEN ELEKTRA
INSTALLATIEHANDLEIDING DELUXE | DEEL I | P1071 REV N

17
CONFORMITEITSVERKLARING
Sunshower B.V., Hoogoorddreef 63-65, 1101 BB Amsterdam (Nederland) verklaart
hierbij op eigen verantwoordelijkheid, dat deze Sunshower DELUXE is gefabriceerd
volgens de voorschriften in de volgende richtlijnen:
• Laagspanningsrichtlijn 2014/35/EU
• Richtlijn 2014/30/EU voor elektromagnetische compatibiliteit van het Europees
Parlement
Normen gebruikt om de conformiteit te ondersteunen:
• EN60335-1:2012 + A11:2014 + AC2014 + A13:2017 + A1:2019
+ A2:2019 + A14:2019
• EN60335-2-27:2014 + A1:2020 + A2:2020
• EN61000-6-3:2007 + A1:2011 + AC:2012
• EN61000-6-1:2007
• EN61000-6-1:2019
• EN61000-3-3:2013
• EN61000-3-2:2014
Dit Sunshower product is IPX5 gekeurd en speciaal ontwikkeld voor gebruik en
installatie in de douche (zone 1).
Nederland, Amsterdam, 1 jan 2020
Ondertekend voor en namens:
M. Wegdam, Technisch Directeur
Sunshower B.V.
Hoogoorddreef 63-65
1101 BB Amsterdam
Nederland
T [phone]
www.sunshower.eu
[e-mail]
INSTALLATIEHANDLEIDING DELUXE | DEEL I | P1071 REV N

18
NIET MEEGELEVERD
GLASPLAAT BINNENWERK WANDFRAME SCHETSPLATEN +
AANSLUITMOFFEN
VOORBEREIDING
ONDERDELEN DOOS
□Kitspuit
□Rolmaat
□Schroevendraaier ( + )
□Waterpas
□Schroeven
□Ventilatiekanalen (rond/
rechthoekig), max. 3 m
□Kanaalbeugels
□Ventilatieroosters
□(Terugslagkleppen)
2x
2x
8x
2x
2x
2x
2x
2x
IN DE DOOS
□Installatiezakje
□Schetsplaten
□Aansluitmoffen
□Brillen
INSTALLATIEHANDLEIDING DELUXE | DEEL I | P1071 REV N

19
D
E
A
B
C
A
B
C
D
E
300 MM
1850 MM
100 MM
450 MM
MIN 165 MM
BENODIGDHEDEN
INSTRUCTIES
Construeer de uitsparing in de muur
volgens de getoonde afmetingen.
VOORBEREIDING
BEMATING
□Rolmaat
□Waterpas
ZIE P22 / P23
INSTALLATIEHANDLEIDING DELUXE | DEEL I | P1071 REV N

20
C B
A
A
B
C
INSTRUCTIES
Zorg voor een YMvK-kabel
van minimaal 2,5mm2en een
potentieelvereffeningskabel van
6mm2zonder PVC-buis of 2,5mm2
met PVC-buis. De Sunshower moet
worden aangesloten op een eigen
230V~ 50Hz groep voorzien van een
aardlekschakelaar (30mA) met een
16A zekering.
VOORBEREIDING
ELEKTRICITEIT
500 MM
VOEDING 3ADERIG
POTENTIAAL
VEREFFENINGSKABEL
INSTALLATIEHANDLEIDING DELUXE | DEEL I | P1071 REV N
!
!
ALLE ELEKTRISCHE WERKZAAMHEDEN
MOETEN WORDEN UITGEVOERD
DOOR EEN ERKEND ELEKTRICIEN
IN OVEREENSTEMMING MET DE
GELDENDE RICHTLIJNEN (HD
603647701 E.D.) EN DE NATIONALE
VOORSCHRIFTEN (BV. VOOR
NEDERLAND NEN 1010  701). ER MOET
EEN APARTE STROOMAANSLUITING
MET APARTE ZEKERING EN APARTE
AARDLEKSCHAKELAAR WORDEN
VOORZIEN.