Roper Rhodes Intense Parts list manual

Intense, Oracle,
Reveal Illuminated Mirror Installation & aftercare instructions
Please retain for future reference
INTENSE
INTENSE
MLE500
ORACLE
ORACLE
MLE510
REVEAL
REVEAL
MLE520
REF: AR.RR.MLE500.510.520| 1.16 V2
Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel: [phone] |Fax: [phone] |Email: [email protected] |Web: www.roperrhodes.co.uk
ELECTRICAL SAFETY INSTRUCTIONS
ELECTRICAL SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All fittings must be installed by a competent person, in accordance with current IEE wiring
regulations. If in doubt consult a qualified electrician
IMPORTANT
Always switch off the electrical supply at the mains during installation and maintenance. It
is recommended that the fuse is withdrawn or the circuit breaker is switched off for the
necessary circuit before installation commences.
Fitting in Bathrooms is subject to the appropriate zone in accordance with IEE Regulations.
This product is suitable for zone 2 and outside zones. IT IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in saunas, steam rooms or shower
cubicles. This product is only suitable for permanent installation. DO NOT connect to a
trailing plug and socket outlet. Although this product has an Ingress Protection rating of
IP44 it is only suitable for indoor use. Do not attach the product to surfaces that are damp or
otherwise electrically conductive.
INSTALLATION CARE & SAFETY
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care when using power tools near water -
the use of a residual current device (RCD) is advised. Beware of hidden cables or pipes.
Take care if drilling on tiled surfaces in case the drill slips. A piece of masking tape applied
to the wall before marking out the fixing holes will stop the drill from wandering.
DO NOT strike glass components with hard or pointed items. DO NOT place very hot or very
cold items against or in close proximity to glass surfaces unless an adequately thick
insulation material is used to prevent such items coming in contact with the glass.
The nominal thickness of the mirror glass used in this product is 5mm and is film backed for
safety. If the glass becomes chipped or broken replace immediately.
This product should be positioned well away from curtains and other fabrics. Never cover
the mirror. This product is heated, we recommend that it is turned off after use and should
never be left on for prolonged periods of time
This product could be dangerous and is only to be installed by a competent person.
CLEANING
CLEANING
It is recommended that the unit is cleaned with a soft, dry, non abrasive cloth when turned
off. Never use cleaning agents or abrasive materials on any type of surface finish. Do not
allow moisture to come into contact with the electrical components.
COMPLIANCE
COMPLIANCE
This product complies with all relevant British and European safety standards:
WIRING
WIRING
This product is manufactured to class I category and must have an earth connection.
COLOUR CODING:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
LIGHTS
LIGHTS
.
To obtain a replacement LED lamp if faulty or broken contact customer services (see details
at foot of page) quoting product code.
22
2
OUTSIDE
OUTSIDE
ZONES
ZONES
2
ZONE
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.75m
Bathroom Zones Diagram
Bathroom Zones Diagram
Distances from a bath tub or shower tray

Intense, Oracle,
Reveal Illuminated Mirror Installation & aftercare instructions
Please retain for future reference
(Oracle Shown for Illustrative Purposes)
(Oracle Shown for Illustrative Purposes)
Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF |Tel: [phone] |Fax: [phone] |Email: [email protected] |Web: www.roperrhodes.co.uk
INSTALLATION PROCEDURE
INSTALLATION PROCEDURE
The wall surface must be of suitable strength and construction.
1)
1)
Measure the distance (x) between the wall fixing pins on the back of the
mirror. For horizontal mounting measure between the fixing pin and the keyhole
slot.
2)
2)
For portrait mounting, mark out the wall mounting plates on the wall using a
pencil to the desired height ensuring they are spaced at distance (x).
If mounting landscape mark out 1 wall mounting plate and mark out a single
screw position using dimension (x) for the keyhole slot.
Drill the marked out positions and fit the wall plugs accordingly. Secure the wall
mounting plates in position with the screws provided.
NOTE: The wall plugs supplied are only suitable for solid stone / brick walls. For
plasterboard walls use specialist wall plugs.
3)
3)
The next step is to make the electrical connection from the mirror to the
mains supply. Use the connection wire found at the rear of the mirror to make
the necessary connections in accordance with the current IEE regulations. A
second person will need to hold the mirror in place whilst electrical
connections are made.
4)
4)
The mirror should slide onto the wall mounting brackets and secure into
place. For a landscape installation, the keyhole slot should be positioned on a
single screw first before sliding onto the wall bracket for ease of installation.
To remove the mirror, the mirror should first be lifted and then pulled away from
the wall.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Lighting is turned on / off by waving a hand past the IR sensor on the mirror
glass, which is positioned in the bottom right when hung portrait and bottom left
when hung landscape. The heated pad is on when the light is on. DO NOT leave
on for prolonged periods of time.
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTURED TO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULT YOUR ELECTRICIAN !
Colour Coding:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
1Measure
Distance X
Measure
Distance X
2
3
4
Mains Supply
Distance X
Back View
Portrait View
Landscape View