Pebble Grey 500.40.70-75 User manual

INSTALLATION GUIDE
Diaz LED Illuminated Mirror 500.40.70-75
Please read these instructions carefully before installation.
Installation should be carried out by a qualified electrician.
IEE Bathroom Zones
IMPORTANT
.
GENERAL
HANDLE WITH CARE!
COMPLIANCE
This product complies with the following safety standards:
BS EN 60598-1: 2008+A11: 2009, EN60598-2-1: 1989
WIRING
COLOUR CODING
LIVE Brown
NEUTRAL Blue
EARTH Green & Yellow
zone
2
radius
zone
2
zone
2
225cm
zone
1
60CM
60CM
60CM
MIN
150mm
When unpacking never stand the unit on a hard
surface. Always lay flat on a soft surface.
To avoid the risk of electrocution, please turn
off the electricity mains supply before
commencing installation.
Please do not hang or drape clothing or material
over the mirror. LEDs can get very hot and this
may cause a fire risk.
Please do not place objects too close to the LEDs
as this will cause the object to burn or melt.
• THIS PRODUCT CONFORMS TO UK SAFETY STANDARDS AND MUST BE
INSTALLED IN ACCORDANCE WITH CURRENT IEE WIRING REGULATIONS
AND BUILDING REGULATIONS (PART P).
• THIS PRODUCT MUST BE EARTHED, AND SHOULD NOT BE CONNECTED
TO AN UNEARTHED CIRCUIT.
• ENSURE THAT CONNECTIONS ARE TURNED OFF AT THE CONSUMER
UNIT OR FUSE BOARD BEFORE INSTALLING OR CARRYING OUT ANY
MAINTENANCE.
• THIS PRODUCT IS FOR INDOOR USE ONLY.
• THIS PRODUCT IS IP44 RATED AND CAN BE INSTALLED IN BATHROOM
ZONE 2 (AS DEFINED BY THE IEE WIRING REGULATIONS) AND BEYOND.
SEE BATHROOM DIAGRAM.
• THE PRODUCT IS SUITABLE FOR INSTALLATION IN ZONE 2 OR HIGHER.
• IF THIS PRODUCT FEATURES REPLACEABLE BULBS THEN REPLACE FAILED
BULBS IMMEDIATELY. ALLOW THE GLASS, LAMP AND FITTING TO COOL
BEFORE REPLACING.
To ensure correct function of the sensor this
product must be installed with a minimum distance
of 150mm between the infrared sensor and any
adjacent worktop, surface, obstruction or tile trim.
• When working at heights, please use a suitable platform to
work from.
• Please note: For new installations, check for any electrical
cables or pipe work (gas/water) in the vicinity of the intended
mounting point before proceeding with the installation.
• Ensure that the fixing location is able to take the weight of the
complete fitting.
• Wear suitable eye protection when drilling. Be careful when
using power tools near water.
Do NOT strike mirror glass with hard or pointed items. It is
recommended that the product is cleaned with a soft, dry, non
abrasive cloth. Do NOT use cleaning agents or abrasive materials
on any type of finished surface. Do NOT allow moisture to come
into contact with the electrical components. Keep your bathroom
well ventilated where possible.
This product is designed and manufactured in the Class 1 category,
meaning a ground wire is required.
Diaz 500.40.70
Diaz 500.40.71 Diaz 500.40.72
Diaz 500.40.73 Diaz 500.40.74 Diaz 500.40.75

INSTALLATION GUIDE
Installation Procedure
1.
Open the carton and make sure all the parts listed below are present
2. Mark a desired height of the mirror. Drill the required holes and insert the wall plugs.
Note: Wall plugs supplied are only suitable for solid stone/brick walls. Please ensure the screws are
fully tight.
3. Make the electrical connections ensuring first that the electrical supply has been turned off.
This mirror is a class 1 product and requires an earth connection. It should be installed in accordance
with the latest IEE regulations.
1X
2X
2X
FLOOR
FROM
HEIGHT
DESIRED
CHOOSE
DISTANCE
A
BETWEEN
CENTERS OF BRACKETS
500.40.70 405
500.40.71 905
500.40.72 305
500.40.73 305
500.40.74 805
500.40.75 1105
605
505
405
505
505
505
A2A1
A1
A2
Live Terminal
Connec�on
Earth Terminal
Connec�on
Output Wires
Neutral Terminal Connec�on

INSTALLATION GUIDE
DISPOSALGUARANTEE
EXTENDED GUARANTEE 100% RECYCLED CARTON
Our cardboard packaging is 100% recycled.
Please dispose of all waste responsibly.
This product has a free replacement parts guaranteed in the UK for a period
of 1 year from the date of purchase. The guarantee is invalid in the case of
improper use, incorrect installation or tampering.
Should this product fail during the guarantee period, please contact our
support team by email at [email protected] and we will replace the
relevant component part free of charge.
Pebble Grey does not accept responsibility for any installation costs
associated with the replacement of the component parts. Your statutory
rights are not affected. Pebble Grey Ltd reserve the right to alter
specifications without prior notice.
We offer an extended guarantee FREE OF CHARGE on selected products.
Activate online within 30 days of purchase to qualify.
For more information visit www.pebblegrey.co.uk/product-guarantee
Waste Electrical & Electronic Equipment Regulations (WEEE) requires that any
of our products showing this mark (left) must not be disposed of with other
household or commercial waste.
Pebble Grey Ltd does not levy any WEEE disposal charges to its customers for
affected WEEE related products.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate any such product from other
waste types and recycle it responsibly at your local facilities. Check with your
Local Authority, Recycling Center or retailer for recycling advice.
Installation Procedure
4.
Hang the mirror onto the wall.
Caution: To avoid interference, the sensor must be placed a minimum of 150mm away from any
object/surface.