Sunsystem Sun Hoist User manual

Grow Light Lift Kit
Congratulations on your purchase of a state of the art Sun Hoist™
Wireless Light Lift System! To ensure that you get the most out of
your Sun Hoist Wireless Light Lift System, please read these instructions
completely and carefully BEFORE installing or operating your system.
To operate your Sun Hoist
Wireless Light Lift System
you will need to download the
MySmartLift application. Go
to Apple Store or Google Play
Store to download. There is no
cost for the MySmartLift app.
INSTALLATION
1Install the mounting rail
in a suitable location above
the desired area with the
screws provided.
Use template printed at the
end of these instructions for
hole placement.
It is the users’ responsibility
to ensure that the support
used is adequate to bear
the weight of the Sun Hoist
System and associated
hardware.
2Slide Sun Hoist onto rail
and tighten thumbscrew to
anchor. Do not over-tighten.
3The Sun Hoist has an auto-
leveling feature that uses a
magnetically mounted sensor
mounted to the top of the
grow light. IMPORTANT : The
level sensor must be mounted
parallel to the front and
back edges of the grow light
housing. ALSO, the sensor
unit logo must be to the front,
with the cord connection on
the left side. See Fig 1.
4Plug the sensor coil cord
into the sensor and into the
corresponding port
on the Sun Hoist labeled
Auto Level Sensor.
Double check the position
of the level sensor and cord
connection for accurate
operation. See Fig 1.
5Attach one end
of the power
supply to the
Sun Hoist port
labeled Power
Port.
The Sun Hoist Wireless Light Lift System is designed to control
a total lighting load of not more than 60 pounds. Ensure that the
light, ballast (if required) and any hood vent hardware DOES NOT
EXCEED 60 pounds total.
SUN HOIST KIT COMPONENTS
• 1 each Sun Hoist Lift Motor • 1 each Auto Level Sensor
• 1 each Power Supply with Cord
• 1 each Mounting Rail with 2 screws
Do not exceed
a total weight
of 60 pounds for
all components.
TIGHTEN
THUMBSCREW
Watch this Sun Hoist
Installation Video after
reading these instructions.
QR
CODE
FIG 1.
4.00 in
MOUNTING RAIL TEMPLATE

Plug the other end of the
power supply into an
appropriate 120V single
phase outlet. A green light
will appear to indicate power.
6Attach the grow light to
the lifting cord using the
carabiners provided.
7Your Sun Hoist system is
now ready to use.
OPERATION
The Sun Hoist is controlled
by the MySmartLift application
using your smart phone or
tablet. Up to 8 Sun Hoists
can be paired to one Station
location. The MySmartLift
application has 8 Station
locations, meaning up to 64
units can be controlled with
one smart phone or tablet, 8 at
a time. The Sun Hoist Bluetooth
connection has a maximum
range of 30 feet. Locate and
download the MySmartLift
application from your favorite
Apple or Android site.
CONNECT
Pairing the Sun Hoist Lift
System to your smart device.
Open the
MySmartLift
application to
the connect
page A.
Press Select
Bfor desired
Station location
(1 - 8) C, avail-
able Bluetooth
devices will
show on screen
with white
background D.
Tap to select
devices to pair.
A system
message “wait
for light“ will
show on screen
and the green
LED on the
Sun Hoist lift
motor will flash
when paired.
The background
color will go from
white to grey. E
Repeat to select
more Sun Hoist
Systems to pair
to a particular
Station location.
Each Sun Hoist Lift System
has a discrete id number that
will display on your smart device.
The id number can be renamed,
if desired. To rename, touch
and hold a white background
location, a name edit screen
will show (up to 11 characters,
max.). Edit name as desired.
Tap done in the upper right
corner to confirm. Close app
from smart device to refresh
name. Reopen app to continue
with new name.
Select a different Lift location
and then reselect the desired
location. After approximately
five seconds, the assign button
will now illuminate. The Sun
Hoist is now ready to operate.
To remove or
add light lifts to
a Station, press
Select Ffor
desired Station
location. Tap
to select or
deselect the
desired edit.
Repeat if
necessary.
Tap done when
complete. Select
a different
Station location
and reselect the
desired location.
The Assign g
button will
now illuminate
and the new
assignments are
ready to operate.
Note: The wireless range
for any Sun Hoist operation is
30 feet. More than one smart
device can have the same pairing,
but only one phone or tablet
can be assigned at a time. If a
phone or tablet is paired and
assigned and within the 30 foot
range, no other smart phone or
SmartLift App
available on
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 1
Cancel Done
MTSenBleBD
MTSenBle93
MTSenBle9A
MTSenBleBB
MTSenBleAE
MTSenBle87
LIFT 1
Cancel Done
MTSenBleBD
MTSenBle93
MTSenBle9A
MTSenBleBB
MTSenBleAE
MTSenBle87
LIFT 1
Cancel Done
MTSenBleBD
MTSenBle93
MTSenBle9A
MTSenBleBB
MTSenBleAE
MTSenBle87
LIFT 1 PAIRING MULTIPLE DEVICES/BUNDLING
HOLD LIFT 1 BUTTON DOWN LIST OF AVAILABLE“DEVICES”
WILL APPEAR
CLICK WHICH “DEVICES”YOU
WANT TO PAIR UNDER “LIFT 1”
ONCE “DEVICES” ARE SELECTED FOR
“LIFT 1”, PRESS DONE.
BY CLICKING DONE, THE APP GOES
BACK TO THE CONNECT PAGE
LIFT 7
LIFT 8
LIFT 7
LIFT 8
D
LIFT 1
Cancel Done
MTSenBleBD
MTSenBle93
MTSenBle9A
MTSenBleBB
MTSenBleAE
MTSenBle87
M
T
S
enB
l
eB
D
M
T
S
e
nB
l
e
93
E
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 7
LIFT 8
CONTROL
LEFT BOTH RIGHT
INFORMATION
TEMPERATURE
HUMIDITY
CARBON DIOXIDE
AUTO LEVEL
C°
28
78
12 %
%RH
MAIN 3 PAGES
A
B
C
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 7
LIFT 8
f
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 7
LIFT 8
g

tablet can control Sun Hoist
until the assigned phone or
tablet is either out of range,
that particular Station location
is deselected, or the smart
phone or tablet placed on
standby or powered off.
CONTROL
Select the
Control icon h
or swipe screen
to the right to
go to the control
screen. The Sun
Hoist has two
motors, Left i
and Right j.
Each motor can
be controlled
independently,
or both motors
at one time k.
Use Up arrow l
or Down arrow
mfor desired
direction. Press-
ing Auto Level
nwith perform
an automated
leveling function at the end of
a move when both motors are
selected. All paired devices
move simultaneously.
Note: A slight pause may take
place during operation due to
the large amount of data being
transferred by bluetooth. This is
normal and only momentary.
INFORMATION
Not in use on Sun Hoist.
REMOTE OPERATION
Simply open the MySmartLift
application on your smart
phone or tablet. Toggle to
connect page and select the
desired Lift Station. Next
toggle to the Control page and
continually press the UP or
DOWN arrows for the desired
direction of travel. Pressing
auto level will perform an
automated function to level the
light fixture at the end of either
an up move or down move
when both motors are selected.
Sensor should level to within
0.5 degrees. Manual level can
be done by selecting the Left
or the Right motor individually,
and arrow Up or Down to move
to desired location.
Warnings
• Properly and securely install
the mounting rail to withstand
forces up to the 60 lb. max
rating.
• Plug power adapter into a
properly grounded 120 VAC
circuit only. DO NOT USE if
power or control cable is cut
or frayed.
• Inspect the Sun Hoist upon
installation to verify proper
lift cord alignment.
• The level sensor is a precision
instrument. The level senor
housing is magnetically
mounting to the steel light
housing and MUST be placed
parallel to the front edge
of the light with the cord
connector on the left hand
side. If installed on the right
side, or if installed at an angle,
the auto level function will
not properly perform.
• Never lift more than 60 lbs.
• Do not stand under Sun Hoist
when lifting.
TROUBLESHOOTING
• If the auto level function
results in an angle greater
than 20 degrees of inclination,
rotate the magnetic level
sensor 180 degrees on the
top of the light. Verify that
the cord is exiting the left side
when the logo on the sensor
is facing you. The sensor
must be placed parallel to
the front edge of the light
with the cord connector on
the left side, not at an angle,
which will adversely affect
the leveling accuracy.
• If you are unable to pair, be
sure another phone is not
already paired and within the
30 foot Bluetooth range.
Warranty Information
SUNLIGHT SUPPLY INC
warrants this product to be
free from defects in materials
and/or workmanship for one
year from date of purchase.
Proof of purchase is required to
obtain warranty coverage. This
warranty does not cover normal
wear and tear, unreasonable
or excessive use, improper
installation, damage and/or
any alterations of this product.
See additional info on long
form warranty.
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 7
LIFT 8
h
CONTROL
LEFT BOTH RIGHT
AUTO LEVEL
i jk
l
m
n
4.00 in
MOUNTING RAIL TEMPLATE
CONNECT
SELECT DEVICE
LIFT 1
LIFT 2
LIFT 3
LIFT 4
LIFT 5
LIFT 6
ASSIGN
LIFT 7
LIFT 8
CONTROL
LEFT BOTH RIGHT
INFORMATION
TEMPERATURE
HUMIDITY
CARBON DIOXIDE
AUTO LEVEL
C°
28
78
12 %
%RH
MAIN 3 PAGES