Sunsystem LEC 315 Manual

IMPORTANT PRODUCT INFORMATION READ IMMEDIATELY
KEEP ORIGINAL PACKAGING – ALL RETURNS NEED TO BEIN THE ORIGINAL PACKAGING
IN ORDER TO AVOID PRODUCT DAMAGE DURING SHIPPING. ANY DAMAGE TO PRODUCTS
NOT IN THEIR ORIGINAL PACKAGING WILL NOT BE COVERED UNDER WARRANTY.
SAFETY FIRST!
FAILURE TO OBSERVE THE FOLLOWING SAFETY WARNINGS MAY RESULT IN SERIOUS INJURY. IN ADDITION, FAILURE TO OBSERVE THESE
SAFETY WARNINGS WILL RESULT IN A WAIVER OF ALL LIABILITIES ON SUNLIGHT SUPPLY®, INC. AND WILL VOID ALL WARRANTIES.
WARNING:
• Disconnect power before re-lamping.
• When re-lamping, make sure lamp has time to cool before touching.
• Make sure power cord and lamp are connected properly.
• Do NOT hang by power cord or lamp cord.
• Do NOT make contact with the interior of the socket while the power is on.
• Do NOT operate the light systems in wet locations.
• Do NOT plug this system into a supply voltage other than what is instructed on the ballast.
• Do NOT attempt to open, rewire or reconfigure any components of the light system.
It will void the warranty and could cause serious injury ordeath.
• These products operate at very high temperatures. Keep away from children.
• Do not plug or unplug a power cord while the ballast isturned on.
• Readall warnings and instructions that come with your lamp
LEC®315 LIGHT EMITTING CERAMIC®
COMMERCIAL FIXTURE
Technical Information Guide
LEC®315 COMMERCIAL SYSTEM SETUP:
1. Remove the system from the box along with all additional parts.
2. Remove socket protector. (Fig. 1)
3. These systems do not require much setup. Attach the reflector to the fixture
using the included thumb screws. (Fig. 2)
4. Carefully insert the proper lamp into the socket making sure you line up the
pins correctly then gently twist until the lamp locks in. Please refer to lamping
installation instructions on back.
5. Hang the fixture using Kendorf Unistrut Brackets or V-hangers provided (Fig. 3).
6. Plug the unit into the proper NEMA configured receptacle or hardwire unit depending
on model voltage.
Fig. 2
Fig. 3
V-hangers Option
Kendorf Unistrut
Brackets Option
Fig. 1
Remove socket protector

TROUBLESHOOTING… IF YOUR FIXTURE DOES NOT WORK:
1. CHECK YOUR ELECTRICAL SOURCE: Make sure the unit is pluggedin properly
and that the breaker is not tripped or fuse blown.
2. CHECK THE LAMP: Make sure the lamp is fully seated in the socket.
WARRANTY SERVICE: Please read warranty information first
If after troubleshooting problems the light will still not work, you shouldreturn the light to the dealer where you purchased it. They will beable to further evaluate
the light and test its various components and quite possibly will be able toidentify and/or fix any problems. Often the problem is as simple as a defectivelamp.
If the dealer is unable to fix the light, they will return it to us for factory repair. Many dealers have loaner fixturesthat you may check out until yours is returned
(usually not more than 7-10 days).
To locate the dealer nearest you, visit our website at www.sunlightsupply.com and complete the “Dealer Search”. If there are no dealers in your area, you may contact us
directly for technical support. If we cannot help you resolve the problem over the phone, we will issue you a RMA # (return merchandise authorization) authorizing you to
return the system to us forfactory reconditioning (if the unit is under warranty). You will needto provide an email address or fax number so that the Authorization Form may be
sent to you. You will need to include this Authorization Form in the packaging when returning your Sun System®unit. Also please write the # on the outside of the box.
Please package the light carefully in its original packaging. If it is damaged in shipment we will not be responsible.
Once we receive the light back, we will repair it within 48 hours (business) and return it to you via UPS Ground. If the unit cannot be repaired, a replacement will be sent.
If there are no replacements available, a comparable unit will be sent back.
IMPORTANT:
PROOF OF PURCHASE REQUIRED FOR RETURNS
SUN SYSTEM®LEC®315 COMMERCIAL FIXTURE = 1 Year Warranty
Returning Units: Please contact your retail store for returns.
WARRANTY INFORMATION:
Sunlight Supply®, Inc. warrantsto the original purchaser of this product against defects in material and workmanship under normal use for 1 year on Sun System®
LEC®315 Commercial fixture. During the warranty period, Sunlight Supply®, Inc. will, at our option, and without charge,repair or replace this product if the unit or
any of its components fail or malfunction.
Thiswarranty is expressly in lieu of all other warranties, expressed or implied, including the warranties of merchantability and fitness for use and of allother
obligations or liabilities on the part of the seller. This warranty shall not apply to this product or any part thereof which hasbeen damaged byaccident, abuse,
misuse,modification, negligence, alteration or misapplication. Sunlight Supply®, Inc. makes no warranty whatsoever in respect to accessories or parts not supplied
by Sunlight Supply®, Inc. This warranty shall apply only to the United States, including Alaska, Hawaii and territories of the United States.
NOTE: Sunlight Supply®, Inc. is a manufacturer of supplementary lighting systems. All sales offerings to the public are done through
a nationwide group of dealers.Nosales offerings will be made directly tothe general public.
www.sunlightsupply.com
04/21/2015
BULB INSTALLATION:
• Use gloves or cloth to avoid handling lamp with bare hands.
• The lamp base has pins with different shapes (Fig. 1).
Line upthe correct pins with the lamp-holder.
• Carefully press down and turn 30 - 45 degrees clockwise until lamp locks in.
The lamp-holder will give a snap-in sensation to confirm proper insertion of the lamp.
Proper Bulb Care
Always unplug your ballast and allow your lamp to cool before changing out your lamp. Lamps should
be changed out after 20,000 hours to maintain maximum lumen output. Running a lamp beyond its
expected life is not recommended and can cause lamp failure as well as a shift in the color spectrum.
Note - Until the lamp has achieved at least 10 hours of operation, the lamp should never be turned off sooner than 2 minutes.
This Includes during installation tests. In cases when this has happened you need to wait 1 hour before switching the lamp on again.
Fig. 1
lampbase
different pins
lamp-holder