SUPER NOVA VK-0004 Manual

© 2020
Order #56343
Locked layer contains
placeholder marks.
Top View
Perspective View
VK-0004 Supernova
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2020
Order #56343
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2020
Order #56343
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
4
13
2
Fold edges over.
Insert into
groove
of frame
SEG Installation

© 2020
Order #56343
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Tool-Less Assembly

© 2020
Case 1 of 1
Order #56343
Locked layer contains
placeholder marks.
3
11A
22A
4A,4A
4,4
Graphics
Setup Hardware
Top View of Each Level
Level 1 (Bottom Level) Level 2 Level 3
Infill
Infill
Infill
5
5
Case Packing

© 2020
Step 1 of 1
Order #56343
Locked layer contains
placeholder marks.
Completed Assembly
Light Box
Infill
Infill
Infill
3
1A
1
Transformer
6
M10 Bolt
M8 Bolt
6A
2
2A
4
4
Item
1,1A
2,2A
3
4
5
6,6A
Qty.
1,1
1,1
1
2
2
1,1
Description
46” CEI110 Horizontal Extrusion
40” CEI110 Vertical Extrusion
40” S44 Vertical Extrusion
19.189” Z31 Horizontal Extrusion
19.189” Z33 Horizontal Extrusion
Base Plate
Steps:
1) Assemble extrusions [1] [1A] [2] and [2A] flat on floor. See CEI110
Tool-Less Assembly sheet.
2) Attach base plates [6] to horizontal [1], using M10 bolt washer and wing
nut. Attach base plate [6A] to vertical [3], using M8 bolt.
Note: Base plate [6A] stays attached to [3], when packing.
3) Connect horizontals [4] and [5] to vertical [2A]. Tighten locks to secure.
4) Insert Infills between horizontals [4] and [5], then secure with vertical [3].
5) Connect lighting power cords and attach transformer.
See Light Connection details.
6) Apply SEG graphic to frontand blocker fabric to back of assembled Light Box.
See General Information sheet for SEG Graphic Installation detail.
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
96W / 4A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 7 light bars per transformer.
5
5
Power
Break
Power
Break
Keep base plate [6A] attached to vertical [3], when packing.
VK-0004 Assembly