Supermicro C7Z87-OCE User manual

SUPERMICR R
ContaCt InformatIon
• www.supermicro.com(Email:[email protected])
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
PaCkage Contents
(Appliestoindividual-packonly)
C7Z87-OCE
QuICk referenCe guIde rev. 1.00
• One(1)SupermicroMotherboard
• Six(6)SATACables
• One(1)I/OShield
MNL-1507-QRG Rev.1.00
© 2013 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
MNL-1507-QRG
• One(1)QuickReferenceGuide
• One(1)DriverCD
A. USB 2.0 Port 0 H. Gb LAN Port 1 N. SPDIF Out
B. USB 2.0 Port 1 I. USB 3.0 Port 6 O. Surround Out
C. HDMI Port J. USB 3.0 Port 7 P. Center/LFE Out
D. VGA Port K. Gb LAN Port 2 Q. Mic In
E. DVI Port L. USB 3.0 Port 4 R. Line Out
F. Thunderbolt Port M. USB 3.0 Port 5 S. Line In
G. Clear CMOS Switch (External)
CLEAR CMOS SWITCH
16
JOCE
A-SATA0I-SATA0 I-SATA2 I-SATA4
LED2LED3
PCIE3 PCIE5
PCIE1
JPUSB2
1
3
JPUSB1
13
JLED1
JVR2
1
3
JPL1
1
JBR1 1
JPME2 1
JPL2
1
JPAC1
1
JPME1 13
JWD1
1
3
JVR1
1
3
JBT1
JSTBY1
1
3
JSD1
+
1
5
19
10
11
11
10
19
1
13
JPCIE2 JPCIE6
JPCIE4
JF1
1
DESIGNED IN USA
C7Z87-OCE
BIOSLICENSE
FORHOME OR OFFICE USE
WithFCC Standards
Testedto Comply
19 20
JTPM1
1
2
JPW2
1
1
7
10
10
7
2
1
1
JPEX_DEBUG
JL1
1
JSPDIF_OUT
1
JI2C1
1
JI2C2
1
24
13
JPW1
1
59
1
JITP1
2
LED1
CATERR_LED
A
C
R298
R97
SP1
41
JCHLED1
1
FAN3
44
1
FAN2
FAN5
1
4
1
FAN1
4
FAN4
1
1
JD1
4
THUNDERBOLT
USB 6/7(3.0)
USB 16/17
USB 4/5(3.0)
USB 14/15
USB 2/3(3.0)
USB 0/1(3.0)
CPU
CPU_SLOT2 PCI-E 3.0 X4 (IN X16)
PCH_SLOT1 PCI-E 2.0 X1 (INX4)
PCH_SLOT5 PCI-E 2.0 X1 (INX4)
PCH_SLOT3 PCI-E 2.0 X1 (INX4)
USB12/13
LAN2 LAN1
HDMI
JWD1:
JBR1:
2-3:BIOSRECOVERY
1-2:NORMAL
JPME1:
2-3:MERECOVERY
1-2:NORMAL
ENABLE
LAN2
DISABLE
2-3
1-2
JPL2
LAN1
DISABLE
ENABLE
2-3
1-2
JPL1
JWOR1:
2-3:NMI
1-2:RST
WATCHDOG
2-3:MEMANUFACTURING MODE
USB 0/1
1-2:NORMAL
JPME2:
JTPM1:TPM/PORT80
JLED1:
3PIN POWER LED
AUDIO FP
HDDPWR
LEDLED
P1-DIMMB1
P1-DIMMB2
NIC1
SPEAKER:1-4
JD1:
BUZZER:3-4
JI2C1/JI2C2
ON:ENABLE
OFF:DISABLE
NIC2
HD AUDIO
WAKEON RING
USB4/5
USB6/7
OH/FF
LED
X
P1-DIMMA1
P1-DIMMA2
RST
PWR
JF1
ON
ALWAYSPOPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED
CPU_SLOT4 PCI-E 3.0 X8 (IN X16)
CPU_SLOT6 PCI-E 3.0 X16
COM1
VGA/DVI
2-3:DISABLE
1-2:ENABLE
JPAC1:AUDIO
POWER BUTTON
USB 2/3
OC1 OC2 OC3
CLEAR
CMOS
CPU
A-SATA1I-SATA1 I-SATA3 I-SATA5
BATTERY
The C7Z87-OCE supports up to 32GB of Unbuffered (UDIMM) DDR3 non-ECC
1600/1333/1066 MHz in 4 memory slots. Populating these DIMM modules
with a pair of memory modules of the same type and same size will result in
interleaved memory, which will improve memory performance.
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Back Panel I/O Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
=mounting hole
A
B
C
D
E
F
G
H
I
Note: Up to 32GB of memory are supported. See chapter 2 of the User Manual for
complete memory population information.
Towards the CPU
Jumpers
Connectors
LED Indicators
DIMM Memory Installation
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the fol-
lowing order: DIMMA2, DIMMB2, then DIMMA1, DIMMB1.
• Always use DDR3 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
Recommended Population (Balanced)
P1-DIMMA2 P1-DIMMB2 P1-DIMMA1 P1-DIMMB1 Total System Memory
2GB 2GB 4GB
2GB 2GB 2GB 2GB 8GB
4GB 4GB 8GB
4GB 4GB 4GB 4GB 16GB
8GB 8GB 16GB
8GB 8GB 8GB 8GB 32GB
LGA 1150
I/O BACK PANEL
Front Panel Control (JF1)
CPU Installation
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED
Reset
PWR
LED_Anode+
LED_Anode+
LED_Anode+
LED_Anode+
Ground
Ground
XX
NIC2 LEDLED_Anode+
J
K
L
M
N
O
P
Q
R
HD Audio
S
Heatsink Installation
Heatsink
with Fan
Motherboard
Mounting Hole
Jumper Description Default
JBT1 Clear CMOS (on board) (See Chpt. 2)
JI2C1/JI2C2 SMB to PCI Slots Off (Disabled)
JPAC1 Audio Enable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPME1 Intel Manufacturing Mode Pins 2-3 (Disabled)
JPME2 Intel Recovery Mode Pins 2-3 (Disabled)
JWD1 Watch Dog Enable Pins 2-3 (NMI)
JBR1 BIOS Recovery Mode Pins 2-3 (Disabled)
JPUSB1 USB Wake Up Enable (Back Panel) Pins 1-2 (Enabled)
JPUSB2 USB Wake Up Enable (USB Headers) Pins 1-2 (Enabled)
Connector Description
I/O Back Panel See Back Panel I/O Connectors, below right
Audio FP Front Panel Audio Header
Battery Onboard Battery
COM1 COM1 Port Header
Fan 1,2,3,4,5 System/CPU Fan Headers (Fan1: CPU Fan)
JD1 Speaker/buzzer (Pins 1-2: Buzzer, Pins 1~4: External Speaker)
JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JLED1 Power LED Indicator Header
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 4-pin CPU power Connector (Required)
JSD1 SATA DOM (Disk On Module) Power Connector
JSPDIF_OUT Sony/Philips Digital Interface (S/PDIF) Out Header
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
SP1 Internal Speaker/Buzzer
A-SATA0/1 (ASMedia) Serial ATA (SATA 3.0) Port 0/1 (6Gb/sec)
I-SATA0~5 (Intel Z87) Serial ATA (SATA 3.0) Ports 0~5 (6Gb/sec)
USB 0/1 Front Panel Accessible USB 3.0 Ports 0/1 (USB 2.0 12/13)
USB 2/3 Front Panel Accessible USB 3.0 Ports 2/3 (USB 2.0 2/3)
USB 4/5, 6/7 Front Panel Accessible USB 2.0 Headers 4/5,6/7,8/9,10/11
JCHLED1 Chassis LED Control (Supermicro Chassis only)
POWERBUTTON Internal Power Button
OC1, OC2, OC3 Over-Clocking Buttons OC1(15%), OC2(20-25%), OC3 (User-Dened in BIOS)
CLEAR CMOS (Below OC2 button) Resets the contents of the CMOS to default values
LED Description Color/State Status
LED1 Onboard Standby PWR LED Green: Solid on Power On
LED2/LED3 Status Display Digital Readout Download the status codes below*
Note for VGA Cards: For a single VGA card, install the VGA card into the JPCIE6 (x16) slot. For SLI™ or CrossFireX™ mode
(two VGA cards linked), install one card each into JPCIE6 (x16) and JPCIE4 (x8) slots.
P1-DIMMB2 (Blue Slot)
P1-DIMMA2 (Blue Slot)
P1-DIMMA1
P1-DIMMB1
*Download the AMI status codes at http://www.ami.com/support/doc/ami_aptio_4.x_status_codes_pub.pdf