Supermicro SuperStorageServer SSG-6019P-ACR12L User manual

USER’S MANUAL
Revision 1.0b
SuperStorageServer®
SSG-6019P-ACR12L

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIALDAMAGESARISING FROM THE USE OR INABILITYTO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical

property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual August 27, 2019
Release Date: Revision 1.0b
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this

to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2019 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!

33
SuperStorageServer SSG-6019P-ACR12L User's Manual
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It provides
information for the installation and use of the SuperStorageServer SSG-6019P-ACR12L.
Installation and maintenance should be performed by experienced technicians only.

on supported memory, processors and operating systems (http://www.supermicro.com).
Notes
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: https://www.supermicro.com/wftp/driver
• Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
If you have any questions, please contact our support team at:
[email protected]m
This manual may be periodically updated without notice. Please check the Supermicro website
for possible updates to the manual revision level.
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates high voltage may be encountered when performing a procedure.
Warning! Indicates important information given to prevent equipment/property damage


4
Preface
Contents
Chapter 1 Introduction
1.1 Overview...............................................................................................................................8
1.2 Unpacking the System .........................................................................................................8
1.3 System Features ..................................................................................................................9
1.4 Server Chassis Features....................................................................................................10
Control Panel ....................................................................................................................10
Front Features...................................................................................................................11
Chassis Rear.....................................................................................................................11
1.5 Motherboard Layout ...........................................................................................................12
Quick Reference Table......................................................................................................13
Chapter 2 Server Installation
2.1 Overview.............................................................................................................................16
2.2 Preparing for Setup ............................................................................................................16
Choosing a Setup Location...............................................................................................16
Rack Precautions ..............................................................................................................17
Server Precautions............................................................................................................17
Rack Mounting Considerations .........................................................................................17
Ambient Operating Temperature....................................................................................17
 ............................................................................................................................17
Mechanical Loading.......................................................................................................18
Circuit Overloading ........................................................................................................18
Reliable Ground.............................................................................................................18
2.3 Installing the Chassis .........................................................................................................19
The Toolless Rail System..................................................................................................19
Sliding the Chassis onto the Rack Rails...........................................................................22
Chapter 3 Maintenance and Component Installation
3.1 Removing Power ................................................................................................................24
3.2 Accessing the System........................................................................................................25
3.3 Motherboard Components..................................................................................................26
Processor and Heatsink Installation..................................................................................26
The Xeon Scalable Processor.......................................................................................26
Assembling the Processor Package..............................................................................27
Removing the Dust Cover from the CPU Socket..........................................................30

5
SuperStorageServer SSG-6019P-ACR12L User's Manual
Installing the Processor Heatsink Module (PHM) ........................................................31
Removing the Processor Heatsink Module from the Motherboard ...............................32
Memory Installation ...........................................................................................................33
ESD Precautions...............................................................................................................33
Precautions....................................................................................................................33
Introduction to Intel® Optane DC Persistent Memory ......................................................33
Memory Support ............................................................................................................33
Memory Installation Sequence ......................................................................................34
General Memory Population Requirements ..................................................................35
DIMM Population Guidelines for Optimal Performance ................................................35
X11DP Motherboards with 12 DIMM Slots....................................................................36
DIMM Installation ..............................................................................................................37
DIMM Module Removal.....................................................................................................37
PCI Expansion Card Installation .......................................................................................38
SAS Backplane Information ..............................................................................................39
Motherboard Battery .........................................................................................................40
3.4 Chassis Components .........................................................................................................41
Storage Drives ..................................................................................................................41
Drive Carrier Indicators..................................................................................................43
Hot-Swap for NVMe Drives ...........................................................................................43
Checking the Temperature of an NVMe Drive ..............................................................44
System Fans .....................................................................................................................45
Checking the Server Air Flow........................................................................................46
Overheating ...................................................................................................................46
Power Supply ....................................................................................................................47
Power Supply LEDs.......................................................................................................48
Chapter 4 Motherboard Connections
4.1 Power Connections ............................................................................................................49
4.2 Headers and Connectors ...................................................................................................50
Control Panel.................................................................................................................53
4.3 Ports ...................................................................................................................................56
Rear I/O Ports................................................................................................................56
Ethernet Ports................................................................................................................57

6
Preface
4.4 Jumpers..............................................................................................................................59
Explanation of Jumpers.................................................................................................59
4.5 LED Indicators....................................................................................................................62
Chapter 5 Software
5.1 Microsoft Windows OS Installation.....................................................................................64
5.2 Driver Installation................................................................................................................66
5.3 SuperDoctor®5...................................................................................................................67
5.4 IPMI ....................................................................................................................................67
Chapter 6 UEFI BIOS
6.1 Introduction.........................................................................................................................68
6.2 Main Setup .........................................................................................................................69
.........................................................................................70
6.4 Event Logs ..........................................................................................................................97
6.5 IPMI.................................................................................................................................... 99
6.6 Security ...........................................................................................................................101
6.7 Boot .................................................................................................................................105
6.8 Save & Exit.......................................................................................................................107
Appendix A BIOS Codes
Appendix B Standardized Warning Statements for AC Systems
Appendix C System Specications
Appendix D UEFI BIOS Recovery
Appendix E CPU-Based RAID for NVMe

7
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw
SuperStorageServer SSG-6019P-ACR12L User's Manual

8
SuperStorageServer SSG-6019P-ACR12L User's Manual
Chapter 1
Introduction
1.1 Overview
This chapter provides a brief outline of the functions and features of the SSG-6019P-ACR12L.
The SSG-6019P-ACR12L is based on the X11DDW-NT motherboard and the
SC802TS-R606WBP chassis.
In addition to the motherboard and chassis, several important parts that are included with
the system are listed below.
Main Parts List
Description Part Number Quantity
1U passive CPU heat sink equipped with a Narrow Retention Mechanism SNK-P0067PS 2
4-Port hybrid backplane supports 4 x 2.5, 7-mm SSD, SATA or NVMe
drives BPN-NVME3-802N-S4 1
4-Port backplane supports 4 x 3.5" SATA3/SAS3 HDD drives or
4-Port backplane supports 4 x 3.5" HDD drives
BPN-SAS3-802A-1 or
BPN-SAS3-802A 3
Riser card RSC-R1UW-2E16 1
Riser card RSC-R1UW-E8R 1
Mezzanine SAS 3224 I/O controller add-on card AOM-S3224-L-P 1
SC802 3.5" internal HDD tray MCP-220-00162-0N 12
 MCP-220-00161-0B 4
Mylar air shroud for SC802 to cover memory MCP-310-00087-0B 4
40x40x56 mm 20.5K RPM / 17.6K RPM counter-rotating fan FAN-0141L4 6
 MCP-290-00153-0N 1
󰀩
1U AC-DC 600W single output power supply Platinum Level, redundant
PWS-606P-1R or
PWS-608P-1R 2
1.2 Unpacking the System
Inspect the box the SuperServer SSG-6019P-ACR12L was shipped in and note if it was

the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be situated
in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and

Be sure to read the precautions and considerations noted in Appendix B.

9
Chapter 1: Introduction
1.3 System Features
The following table provides you with an overview of the main features of the

System Features
Motherboard
X11DDW-NT
Chassis
SC802TS-R606WBP
CPU
Intel® Xeon® 81xx/61xx/51xx/41xx/31xx or 82xx/62xx/52xx/42xx/32xx series processor
Socket Type
Socket P (LGA 3647)
Memory
Twelve DIMM slots support up to 3 TB of ECC DDR4-2933/2666/2400/2133 MHz speed NVDIMM, RDIMM
(Registered DIMM), LRDIMM (Load-Reduced DIMM) or 3DS LRDIMM memory. Supports Intel® Optane™
DCPMM memory.
Chipset
Intel C622
Expansion Slots
One PCI-E 3.0 x32 slot with riser card (RSC-R1UW-2E16)
One PCI-E 3.0 x16 slot mezzanine with SAS support
One PCI-E 3.0 x16 slot with riser card (RSC-R1UW-E8R)
Hard Drives
Twelve 3.5" internal HDD drive bays and four internal 2.5" HDD/SSD/NVMe drive bays
Power
Redundant 600W hot-swap power supply modules (2x)
Form Factor
1U rackmount
Dimensions
W x H x D: 17.6" (447mm) x 1.7" (43mm) x 39.76" (1010mm)

10
SuperStorageServer SSG-6019P-ACR12L User's Manual
1.4 Server Chassis Features
Control Panel
󰀨

panel are described below. See Chapter 4 for details on the control panel connections.
Universal Information LED
Status Description
Continuously on and red An overheat condition has occurred. (This may be caused by cable congestion.)
Blinking red (1 Hz) Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz) Power failure: check for an inoperative power supply.
Solid blue UID has been activated locally to locate the server in a rack environment.
Blinking blue (300 msec) UID has been activated using IPMI to locate the server in a rack environment.
Figure 1-1. Control Panel
Control Panel Features
Item Features Description
1Power button
The main power switch applies or removes primary power from the power supply to
the server but maintains standby power. To perform most maintenance tasks, unplug
the system to remove all power.
2Reset button The hardware reset button is used to reboot the system, if needed, without powering
󰀨
3Power LED Indicates power is being supplied to the system power supply units. This LED is
illuminated when the system is operating normally.
4HDD LED 
5NIC LED 
6NIC LED 
7Information
LED Alerts operator to several states, as noted in the table below.
16 5 4 37 2

11
Chapter 1: Introduction
Front Features
The SC802TS-R606WBP is a 1U chassis See the illustration below for the features included
on the front of the chassis.
Figure 1-2. Front Chassis View
Front Chassis Features
Item Feature Description
1Control Panel Control panel (see previous page for details)
2Locking Levers
Loosen the two thumb screws on the front of the chassis to unlock the
levers on both sides, then rotate counter clockwise to unlock, clockwise
to lock. Pulling out the two levers at the same time will pop out the
internal drive drawer, which you can pull out.
Chassis Rear
The illustration below shows the features included on the rear of the chassis. Power supply
modules display status lights.
Figure 1-3. Rear View
Rear Chassis Features
Item Feature Description
1Power Supply Module 600W power supply (redundant, with two power modules)
2I/O Ports I/O ports (see Section 4.3 for details)
3PCI Expansion Slots Three PCI Expansion slots for add-on cards (see Section 3.4 for
details)
4Rack Ear Brackets Attaches server chassis to the rack
Expansion Ports
1
2
13
3
3
44
1
22

12
SuperStorageServer SSG-6019P-ACR12L User's Manual
Figure 1-4. Motherboard Layout
1.5 Motherboard Layout

the table on the following page for descriptions. For detailed descriptions, pinout information

JBMC_DEBUG
SRW1
JSDCARD1
JM2_1
JUIDB1
JP3
FAN5FAN6
FAN4 FAN3 FAN2 FAN1
JBT1
LE3
LE1
C
A
LEDM1
LE2
JNVI2C1
JIPMB1
JNVI2C2
JPME2
JPME1
JPL1
JPG1
S-SGPIO2
BT1
+
JSTBY1
JD1
1
JVRM1JVRM2
JL1
JP2
JF1
JPWR1 JPWR2
JPI2C1
JPWR3
JTPM1
JRK1
JSXB1_2
JAOM
JSXB1_1
JSXB1_3
BAR CODE
X11DDW-NT
REV:1.02
MAC CODE
DESIGNED IN USA
BIOS LICENSE
I-SATA 4~7
I-SATA 0~3
S-SATA 0~3
P1_NVME1 P1_NVME0
P2_NVME1
P2_NVME0
CPU2_PORT2ACPU2_PORT2BCPU2_PORT2CCPU2_PORT2DCPU1_PORT3CCPU1_PORT3DCPU1_PORT3CCPU1_PORT3D
CPU1_PORT3BCPU1_PORT3ACPU1_PORT3BCPU1_PORT3A
SXB1B:CPU1 PCI-E 3.0 X16 + CPU2 PCI-E 3.0 X16
CPU2_PORT3 SXB2:CPU2 PCI-E 3.0 X16
USB4/5(3.0)
USB0/1(3.0)
USB2/3
(3.0)
S-SATA5 S-SATA4
VGA
LAN1
LAN2
X NMIPWR
LED
NIC HDD
LED
NIC
2 1
UID
LED
PS
FAIL
PWRRST
ON
IPMI_LAN
F1
P1 DIMM
E1 D1
CPU1
JWD1
JBR1
CPU1
P1 DIMM
B1
A1 C1
A1
P2 DIMM
B1 C1
CPU2
F1
P2 DIMM
E1 D1
CPU2
C620
10G PHY
BMC
VGA
JPG1
CPU1+CPU2 PCI-E 3.0 X16
SRW1
JPWR2
JSTBY1
USB4/5
BT1
JBT1
JL1
FAN6
LE3
S-SATA0~3
JM2_1
JTPM1
FAN5 FAN4 FAN3 FAN2 FAN1
JPWR1
JPWR3
LEDM1
S-SATA5
S-SATA4
JPI2C1
JPL1
JIPMB1
JWD1
JF1
LE2
JD1
JVRM2
IPMI LAN
USB0/1
USB2/3`
LAN1
LAN2
JRK1
JPME2
JPME1
LE1
JUIDB1
JNVI2C2
P2_NVME1 P2_NVME0
P1_NVME0
JSDCARD1
P1_NVME1
T-SGPIO1 JVRM1
JBMC DEBUG
JNVI2C2
CPU2 PCI-E 3.0 X16
I-SATA0~3
I-SATA4~7
JP3
JP2
JSXB1_1
JSXB1_3
CPU1CPU2
Notes:
• -
tions.
• " " indicates the location of Pin 1.
• Jumpers/LED indicators not indicated are used for testing only.

13
Chapter 1: Introduction
Quick Reference Table
Jumper Description Default Setting
JBT1 Clear CMOS Open (Normal)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)
JPME1 ME Recovery Pins 1-2 (Normal)
JPME2 Manufacturing (ME) Mode Select Pins 1-2 (Normal)
JVRM1 VRM SMB Clock (to BMC or PCH) Pins 1-2 (BMC, Normal)
JVRM2 VRM SMB Data (to BMC or PCH) Pins 1-2 (BMC, Normal)
JWD1 Watch Dog Timer Pins 1-2 (Normal)
Connector Description
Battery (BT1) Onboard CMOS battery
FAN1~6 System cooling fan headers
IPMI_LAN Dedicated IPMI LAN port
JAOM PCI-E 3.0 x16 SAS3 AOM controller slot
JD1 Power LED/Speaker header (Pins 1-3: power LED, Pins 4-7: speaker)
JF1 Front control panel header
JIPMB1 4-pin external BMC I2C header (for an IPMI card)
JL1 Chassis intrusion header
JM2_1 M.2 slot supported by PCH
JNVI2C1/JNVI2C2 NVMe I2C headers
JPI2C1 Power Supply SMBbus I2C header
JPWR1/JPWR2 12V 8-pin power supply connectors
JPWR3 24-pin ATX main power supply connector
JRK1 RAID Key for onboard SATA devices
JSDCARD1 Micro SD Card slot
JSTBY1 Standby power header
JTPM1 Trusted Platform Module (TPM)/Port 80 connector
JUIDB1 
LAN1/LAN2 Gigabit LAN (GLAN) Ethernet ports on the back panel
P1_NVME0/P1_NVME1 NVM Express PCI-E 3.0 x4 ports (from CPU1)
P2_NVME0/P2_NVME1 NVM Express PCI-E 3.0 x4 ports (from CPU2)
(I-)SATA0~3, 4~7 I- SATA 3.0 connectors supported by the Intel PCH
(S-)SATA0~3 S-SATA 3.0 connectors supported by the Intel SCU
(S-)SATA4/S-SATA5 S-SATA connectors with built-in power pins and support of Supermicro SuperDOM (Disk-on
Module) devices
SXB1 PCI-E 3.0 (x16 + x16) Left Riser Card slot supported by CPU1 and CPU2
•              
Install the onboard battery correctly to avoid any possible explosion.

14
SuperStorageServer SSG-6019P-ACR12L User's Manual
Connector Description
SXB2 PCI-E 3.0 x16 Right Riser Card slot supported by CPU2
T-SGPIO3 Serial General Purpose I/O port
USB0/1 Back panel USB 3.0 ports
USB2/3 Back panel USB 3.0 ports
USB4/5 USB 3.0 headers
VGA Back panel VGA port
LED Description Status
LE1  
LE2 Onboard Power LED On: Onboard Power On
LE3 M.2 LED Blinking Green: Device Working
LEDM1 BMC Heartbeat LED Blinking Green: BMC Normal

15
Chapter 1: Introduction
Figure 1-5. Intel C622 Chipset: System Block Diagram
Note: This is a general block diagram and may not exactly represent the features on your

motherboard.
Note: ports available on the (-NT) model only.
SPI
LAN3
RGRMII
Debug Card
FRONT PANEL
SYSTEM POWER
CTRL
FAN SPEED
PCI-E X1 G2
USB 2.0
#12
KR/KX
INTEL
PCH
6.0 Gb/S
USB 2.0
USB
#1
#0
SATA
#5
#4
RTL8211E-VB-CG
#3
#2
RJ45
BIOS
(OPTION)
ESPI
SPI
Temp Sensor
EMC1402-1 *2 at diff SMBUS
TPM HEADER
USB 3.0
USB
BIOS
SPI
AST2500
BMC#5
RMII/NCSI
VGA CONN
BMC Boot Flash
DDR4
5+1 PHASE
145W
2133/2666
2133/2666
DDRIV
P1
P1
P0
VR13
P0 #G-0
DDRIV
#D-0
#C-0
#B-0
#A-0
UPI
PCI-E X4 + X4 G3
DMI3
2 x NVME
#E-0
#F-0
SNB CORE
DDR-IVSNB CORE
DDR-IV
UPI
10.4/11.2G
5+1 PHASE
145W
VR13
LUIO
NA
PCI-E X4 + X4 G3
PCI-E X8 G3
#H-0
#J-0
#K-0
#L-0
#M-0
#6
#7
#8
#9
VCCP1 12v
VCCP0 12v
UPI
VCCP0-(F)
#3
ESPI
Header
PCI-E X8 G3
X8 UPLINK NO QAT (~17W)
* TBD
X557-AT2/88E1512
RJ45
10G/1G
RJ45
10G/1G
Rear x4
Header x2
iPass 4x3
SuperDOM x2
JAOM
PCI-E X16 G3
LUIO
PCI-E X16 G3
RUIO
P2P2
LAN 10G/1G
#10
SATA
#11
#13
#12
X8 UPLINK NO QAT (~15W)
(LANE REVERSE)
(LANE REVERSE)
2 x NVME
(LANE REVERSE)PCI-E X16 G3
(LANE REVERSE)PCI-E X16 G3
VCCP1
#2 #1B#1A DMI3 DMI3
SOCKET ID : 0 SOCKET ID : 1
PECI : 30 PECI : 31
#1A #1B #2 #3
USB2.0
4 x NVME (2+2)

SuperStorageServer SSG-6019P-ACR12L User's Manual
16
Chapter 2
Server Installation
2.1 Overview
This chapter provides advice and instructions for mounting your system in a server rack.
If your system is not already fully integrated with processors, system memory etc., refer to

Caution: Electrostatic Discharge (ESD) can damage electronic components. To prevent such
damage to PCBs (printed circuit boards), it is important to use a g
1ounded wrist strap, handle all PCBs by their edges and keep them in anti-static bags when
not in use.
2.2 Preparing for Setup
The box in which the system was shipped should include the rackmount hardware needed to
install it into the rack. Please read this section in its entirety before you begin the installation.
Choosing a Setup Location
• The system should be situated in a clean, dust-free area that is well ventilated. Avoid areas

• Leave enough clearance in front of the rack so that you can open the front door completely
(~25 inches) and approximately 30 inches of clearance in the back of the rack to allow
󰀩
• This product should be installed only in a Restricted Access Location (dedicated equipment
rooms, service closets, etc.).
• This product is not suitable for use with visual display workplace devices according to §2
of the German Ordinance for Work with Visual Display Units.

Chapter 2: Server Installation
17
Rack Precautions
• 
the full weight of the rack rests on them.
• In single rack installations, stabilizers should be attached to the rack. In multiple rack in-
stallations, the racks should be coupled together.
• Always make sure the rack is stable before extending a server or other component from
the rack.
• You should extend only one server or component at a time - extending two or more simul-
taneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Appendix B.
• Determine the placement of each component in the rack before you install the rails.
• 
way up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from power
surges and voltage spikes and to keep your system operating in case of a power failure.
• Allow any drives and power supply modules to cool before touching them.
• When not servicing, always keep the front door of the rack and all covers/panels on the
servers closed to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of
the rack environment may be greater than the room's ambient temperature. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (TMRA).
Airow
               
operation is not compromised.

SuperStorageServer SSG-6019P-ACR12L User's Manual
18
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not arise due
to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power supply circuitry
󰀨
and power supply wiring. Appropriate consideration of equipment nameplate ratings should
be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself should be
grounded. Particular attention should be given to power supply connections other than the
direct connections to the branch circuit (i.e. the use of power strips, etc.).

special precautions to ensure that the system remains stable. The following guidelines
are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• 
with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the unit in the rack.

Chapter 2: Server Installation
19
2.3 Installing the Chassis
This section provides information on installing the chassis into a rack unit with the rails
provided.
The Toolless Rail System
The SC802 chassis uses a toolless rail system that does not need -- as the name implies
-- any hand tool to mount the rails and chassis into the server rack. The toolless rail system
has locking mechanisms on each end of the rails that latch and lock onto the square mounting
holes which are located on the front and back of the server rack. When these rails are secure,
the chassis' left and right sides will simply rest on the inner rail 'lip' of these rails, which can
be freely pulled out or pushed in as needed. The chassis is then secured to the rack by two
thumb screws.
Insert the mounting ends of the rails into
the square mounting holes in 1U space
on the rack post
Figure 2-1. Toolless Rails
Left Rail
Right Rail
Inner Rail Lip
Mounting Ends
Mounting Ends
1U Space
Top Hook
Bottom Lock
Mounting End
Rack Post

SuperStorageServer SSG-6019P-ACR12L User's Manual
20
Figure 2-2. Installing the Outer Rails to the Rack
Insert the top hook rst, push it
downwards to allow its hook to rest and
engage the selected mounting hole.
1
A
When the top hook is rested and engaged into
place, push the bottom lock into the lower hole
until it clicks and snaps into place
Insert until bottom lock snaps into place.
This push button will pop out to indicate it is
locked.
Top hook
Bottom lock
This illustration shows a sideways view of one
properly mounted rail.
1
B