Supero SuperServer 6028U Series User manual

SUPER ®
USER’S MANUAL
Revision 1.0
SUPERSERVER®
6028U SERiES

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: November 03, 2014
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

3
Preface
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer. Installation and
maintainance should be performed by experienced technicians only.
Please refer to the server specications page on our Web site for updates on
supported memory, processors and operating systems (www.supermicro.com).
Notes
For your system to work properly, please follow the links below to download all
necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://super-dev/about/policies/safety_information.cfm
If you have any questions, please contact our support team at:
[email protected]
This manual may be periodically updated without notice. Please check the
Supermicro Web site for possible updates to the manual revision level.
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates high voltage may be encountered when performing
a procedure.
Warning! Indicates important information given to prevent equipment/
property damage or personal injury.

4
SUPERSERVER 6028U Series Manual
Contents
Chapter 1 Introduction..............................................................................1-1
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Onboard Serial ATA ........................................................................................ 1-2
Rear I/O Ports................................................................................................. 1-2
Graphics Controller ......................................................................................... 1-2
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
Hard Drives ..................................................................................................... 1-3
PCI Expansion Slots ....................................................................................... 1-3
Front Control Panel......................................................................................... 1-3
Cooling System............................................................................................... 1-3
NVMe .............................................................................................................. 1-4
1-4 Contacting Supermicro.................................................................................... 1-5
Chapter 2 Server Installation
2-1 Unpacking the System .................................................................................... 2-1
2-2 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-3 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
6-5 Installing the System into a Rack ................................................................. 2-4
Identifying the Sections of the Rack Rails...................................................... 2-4
Releasing the Inner Rail ................................................................................. 2-5
Installing the Inner Rails on the Chassis ........................................................ 2-6
Installing the Outer Rails onto the Rack......................................................... 2-7
Sliding the Chassis onto the Rack Rails......................................................... 2-8
Chapter 3 System Interface......................................................................3-1
3-1 Overview ......................................................................................................... 3-1

5
Preface
3-2 Control Panel Buttons ..................................................................................... 3-2
3-3 Control Panel LEDs ........................................................................................ 3-2
Overheating..................................................................................................... 3-3
Overheat Temperature Setting ................................................................... 3-3
Responses.................................................................................................. 3-3
3-4 Drive Carrier LEDs.......................................................................................... 3-4
3-5 Power Supply LEDs ........................................................................................ 3-4
Chapter 4 Standardized Warning Statements for AC Systems
About Standardized Warning Statements....................................................... 4-1
Warning Denition........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies (if applicable to your system)........................... 4-12
Backplane Voltage (if applicable to your system)......................................... 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning (if applicable to your system) ................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Installing the Processor and Heatsink ............................................................ 5-2
Installing an LGA 2011 Processor................................................................... 5-2
Installing a CPU Heatsink ............................................................................... 5-5
Removing the Heatsink .................................................................................. 5-6
5-3 Connecting Cables.......................................................................................... 5-7
Connecting Data Cables ................................................................................. 5-7
Connecting Power Cables .............................................................................. 5-7
Connecting the Control Panel......................................................................... 5-7
5-4 I/O Ports.......................................................................................................... 5-8
LAN Ports........................................................................................................ 5-8
5-5 Installing Memory............................................................................................ 5-9
Memory Support............................................................................................ 5-10
Processor and Memory Module Population Conguration ...................... 5-10

6
SUPERSERVER 6028U Series Manual
Populating DDR4 Memory Modules......................................................... 5-10
5-6 Serverboard Details .......................................................................................5-11
Serverboard Quick Reference....................................................................... 5-12
5-7 Connector Denitions.................................................................................... 5-14
Power Connectors ....................................................................................... 5-14
Control Panel Connector............................................................................... 5-14
Other Connectors.......................................................................................... 5-17
5-8 Jumper Settings ............................................................................................ 5-20
5-9 Onboard Indicators........................................................................................ 5-22
5-10 SATA Ports .................................................................................................... 5-23
5-11 Installing Software......................................................................................... 5-24
SuperDoctor®5 ............................................................................................. 5-25
5-12 Onboard Battery............................................................................................ 5-26
Chapter 6 Advanced Chassis Setup........................................................6-1
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Removing the Chassis Cover ......................................................................... 6-3
6-4 Hard Drive Installation..................................................................................... 6-4
6-5 Adding PCI Expansion Cards ......................................................................... 6-7
6-6 System Fans ................................................................................................. 6-10
Replacing System Fan.................................................................................. 6-10
Air Shroud ......................................................................................................6-11
6-7 Power Supply................................................................................................ 6-12
Replacing a Power Supply Module............................................................... 6-12
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
Starting the Setup Utility ................................................................................. 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-25
7-5 IPMI............................................................................................................... 7-27
7-6 Security......................................................................................................... 7-29
7-7 Boot............................................................................................................... 7-30
7-8 Save & Exit ................................................................................................... 7-31
Appendix A BIOS Error Beep Codes ..................................................... A-1
Appendix B System Specications ........................................................ B-1

Chapter 1
Introduction
1-1 Overview
The SuperServer 6028U Series is a high-end server comprised of two main
subsystems: the SC829UAC(4)-R1K02 2U server chassis and the X10DRU-i+
dual processor serverboard. Refer to the Supermicro web site for information on
operating systems that have been certied for use with the system (www.supermicro.
com).
6028U Series Models
System LAN Ports NVMe Ultra Riser Card Backplane
6028U-TR4+ Four GbE no AOC-2UR68-i4G BPN-SAS3-826A
6028U-TRT+ Two 10GBase-T no AOC-2UR68-i2XT BPN-SAS3-826A
6028U-TR4T+ Four 10GBase-T no AOC-2UR6-i4XT BPN-SAS3-826A
6028U-TRTP+ Two 10G SFP+ no AOC-2UR68-i2XS BPN-SAS3-826A
6028U-TNRT+ Two 10GBase-T 4 port AOC-2UR8N4-i2XT BPN-SAS3-826A-N4
6028U-TNR4T+ Four 10GBase-T 4 port AOC-2URN4-i4XT BPN-SAS3-826A-N4
In addition to the above components, the server includes:
•Four 8-cm system cooling fans (FAN-0118L4)
•Two passive CPU heatsinks (SNK-P0058PSU)
•One air shroud (MCP-310-82908-0B)
•Twelve hard drive carriers (MCP-220-00075-0B)
•Riser Cards:
One RSC-R1UW-E8R-O-P
One RSC-R2UW-4E8-O-P
•One rackmount rail kit (MCP-290-00053-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://super-dev/about/policies/safety_information.cfm
For support, email [email protected].
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6028U Series User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6028U Series lies the X10DRU-i+, a dual processor
serverboard based on the Intel PCH C612 chipset. Below are the main features of
the serverboard. (See Figure 1-1 for a block diagram of the chipset.)
Processors
The serverboard supports single or dual Intel E5-2600 v3 Series processors in
LGA2011 sockets (Socket R3). Refer to the Supermicro web site for a complete
listing of supported processors (www.supermicro.com).
Memory
The serverboard has 24 memory sockets that can support up to 768 GB of ECC
registered DDR4-1600/1333/1066/800 non-volatile RDIMM (Registered DIMMs)
or 1536 GB of LRDIMM (Load-Reduced DIMMs) DDR4-2133/1866/1600/1333
memory. Please refer to Chapter 5 for installing memory.
Onboard Serial ATA
A SATA controller is integrated into the chipset to provide a ten-port SATA
subsystem. Six of the ports are supported by the Intel PCH and four of the ports are
supported by the Intel SCU. The SATA 3.0 ports are connected to the backplane
by default. RAID 0, 1, 5 and 10 are supported by Intel RSTe Software RAID.
Rear I/O Ports
The rear I/O ports include one COM port, a VGA (monitor) port, two USB 3.0 ports
and a dedicated IPMI LAN port. In addition, there are several possible networking
congurations depending on the pre-installed Ultra riser card. See the table in
Secion 1-1.
Graphics Controller
The serverboard features an integrated ASpeed 2400 BMC graphics chip.

1-3
Chapter 1: Introduction
1-3 Server Chassis Features
The 6028U Series is built upon the SC829UAC-R1K02 chassis or the SC829UAC4-
R1K02 for NVMe models. Details and related procedures can be found in Chapter
6.The following is a general outline of the main features of the chassis.
System Power
The chassis features a redundant 1 KW power supply consisting of two hot-plug
power modules. They have 80 Plus certication at Titanium Level (96%) high-
efciency. The system will continue to operate if one module fails or is replaced.
Hard Drives
The chassis supports up to twelve 3.5" hot-swap hard drives.
PCI Expansion Slots
All 6028U Series models include two WIO riser cards that support PCI-Express 3.0
expansion cards— four full size x8 cards and one low prole x8 card.
In addition, each system comes with an Ultra riser card to provide added features
such as LAN ports and additional PCI expansion slots.
System Ultra Riser Card Ultra Riser Additional PCI-E 3.0 Support
6028U-TR4+ AOC-2UR68-i4G One PCI-E x8 (Supermicro SAS only)
One PCI-E x8 (in x16 slot)
One PCI-E x16
6028U-TRT+ AOC-2UR68-i2XT
6028U-TRTP+ AOC-2UR68-i2XS
6028U-TR4T+ AOC-2UR6-i4XT One PCI-E x8 (Supermicro SAS only)
One PCI-E x16
6028U-TNRT+ AOC-2UR8N4-i2XT One PCI-E x8 (Supermicro SAS only)
One PCI-E x8 (in x16 slot)
6028U-TNR4T+ AOC-2URN4-i4XT One PCI-E x8 (Supermicro SAS only)
Front Control Panel
The chassis front control panel provides system monitoring and power control.
Status LEDs indicate system power, HDD activity, network activity, UID, and
overheat and fan failure.
Cooling System
The chassis has an innovative cooling design that features four 8-cm high-
performance fans. Fan speed can be determined by system temperature via IPMI.
Each power supply module also includes a cooling fan.

1-4
SUPERSERVER 6028U Series User's Manual
Figure 1-1. Intel PCH C612 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
x8
x8
x8
x8
x8
Port A Port B Port B NCSI Port C Port C
NIC
Port A
0~7
Port B
0~7
Port B
8~15
Port C
0~10
Port C
11~15
Port 0, 1 Port 3
Type A
Rear
A
BD
C
E
F
G
H
#1 #1 #1 #1 #1 #1 #1 #1
#2 #2 #2 #2 #2 #2 #2 #2
#3 #3 #3 #3 #3 #3 #3 #3
DDR4 DIMM DDR4 DIMM
DDR4 DIMM
DDR4 DIMM
DDR4 DIMM
DDR4 DIMM DDR4 DIMM
DDR4 DIMM
x8
x4
x16
x16
PE1 PE2 PE3 PE1 PE2 PE3 QPI1 QPI0
QPI1 QPI0
DMI
DMI
Upper
Upper
Lower
Lower
Processor
Processor
VGA
DDR3 NCSI
LAN
UART
Onboard TPM (Optional)
NVMe
The NVM Express ports provide high-speed, low-latency connections directly from
the CPU to NVMe Solid State drives (SSDs). This greatly increases SSD throughput
and signicantly reduces storage device latency by simplifying driver and software
requirements resulting from the direct PCI-E interface between the CPU and the
NVMe SSD drives.

1-5
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Web Site: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web Site: www.supermicro.com.tw

1-6
SUPERSERVER 6028U Series User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
This chapter provides instructions for preparing and mounting your chassis in a rack.
2-1 Unpacking the System
You should inspect the box the chassis was shipped in and note if it was damaged
in any way. If the chassis itself shows damage, le a damage claim with the carrier
who delivered it.
2-2 Preparing for Setup
Decide on a suitable location for the rack unit that will hold your chassis. It should
be a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical
noise and electromagnetic elds are generated. A nearby grounded power outlet.
is required
The box your chassis was shipped in should include two sets of rail assemblies, two
rail mounting brackets and the mounting screws to mount the system into the rack.
Please read this chapter in its entirety before beginning the installation procedure.
Choosing a Setup Location
•Leave at least 25 inches clearance in front of the rack to open the front door
completely.
•Leave approximately 30 inches of clearance in the back of the rack to allow for
sufcient airow and access for servicing.
•It should be a restricted access location, such as a dedicated equipment room
or a service closet.

2-2
SUPERSERVER 6028U Series User's Manual
2-3 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more
simultaneously may cause the rack to become unstable.
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
rails.
•Install the heaviest server components on the bottom of the rack rst, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow the hot plug SAS drives and power supply modules to cool before touching
them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
•Slide rail mounted equipment is not to be used as a shelf or a work space.

2-4
SUPERSERVER 6028U Series User's Manual
6-5 Installing the System into a Rack
This section provides information on installing the server into a rack unit with the
rack rails provided. There are a variety of rack units on the market, so the assembly
procedure may differ slightly. Refer to the installation instructions that came with
your rack. Note: This rail will t a rack between 26.5" and 36.4" deep.
Identifying the Sections of the Rack Rails
The chassis package includes two rail assemblies. Each assembly consists of three
sections: An inner rail that secures directly to the chassis, an outer rail that secures
to the rack, and a middle rail which extends from the outer rail. These assemblies
are specically designed for the left and right side of the chassis.
Figure 6-1. Identifying the Outer Rail, Middle Rail and Inner Rail
(Left Rail Assembly Shown)
Inner Rail
Rail Assembly
(Shown with Rails
Retracted)
This Side Faces
Outward
Locking Tab
Middle Rail
Outer Rail

Chapter 2: Server Installation
2-5
Figure 6-2. Extending and Releasing the Inner Rail
Releasing the Inner Rail
Each inner rail has a locking latch. This latch prevents the server from coming
completely out of the rack when when the chassis is pulled out for servicing.
To mount the rail onto the chassis, rst release the inner rail from the outer rails.
Releasing Inner Rail from the Outer Rails
1. Pull the inner rail out of the outer rail until it is fully extended as illustrated below.
2. Press the locking tab down to release the inner rail.
3. Pull the inner rail all the way out.
4. Repeat for the other outer rail.
1
1
1
2
1
3

2-6
SUPERSERVER 6028U Series User's Manual
Figure 6-3. Installing the Inner Rails
Installing the Inner Rails on the Chassis
Installing the Inner Rails
1. Identify the left and right inner rails. They are labeled.
2. Place the inner rail rmly against the side of the chassis, aligning the hooks on
the side of the chassis with the holes in the inner rail.
3. Slide the inner rail forward toward the front of the chassis until the quick release
bracket snaps into place, securing the rail to the chassis.
4. Optionally, you can further secure the inner rail to the chassis with a screw.
5. Repeat for the other inner rail.
Figure 6-4. Inner Rails Installed on the Chassis
1
3
1
4
1
4
1
2
Inner Rails

Chapter 2: Server Installation
2-7
Figure 6-5. Extending and Mounting the Outer Rails
1
1
1
2
1
3
1
4
21D01
L-min=676.00(26.61")(outer rail)
Installing the Outer Rails onto the Rack
Installing the Outer Rails
1. Press upward on the locking tab at the rear end of the middle rail.
2. Push the middle rail back into the outer rail.
3. Hang the hooks on the front of the outer rail onto the square holes on the front
of the rack. If desired, use screws to secure the outer rails to the rack.
4. Pull out the rear of the outer rail, adjusting the length until it just ts within the
posts of the rack.
5. Hang the hooks of the rear section of the outer rail onto the square holes on the
rear of the rack. Take care that the proper holes are used so the rails are level.
If desired, use screws to secure the rear of the outer rail to the rear of the rack.
6. Repeat for the other outer rail.
Stability hazard. The rack stabilizing mechanism must be in place, or the rack
must be bolted to the oor before you slide the unit out for servicing. Failure to
stabilize the rack can cause the rack to tip over.
Do not use a two post "telco" type rack.

2-8
SUPERSERVER 6028U Series User's Manual
Figure 6-6. Installing into a Rack
Ball-Bearing
Shuttle
Sliding the Chassis onto the Rack Rails
Warning: Mounting the system into the rack requires at least two people to
support the chassis during installation. Please follow safety recommendations
printed on the rails.
Installing the Chassis into a Rack
1. Extend the outer rails as illustrated above.
2. Align the inner rails of the chassis with the outer rails on the rack.
3. Slide the inner rails into the outer rails, keeping the pressure even on both
sides. When the chassis has been pushed completely into the rack, it should
click into the locked position.
4. Optional screws may be used to hold the front of the chassis to the rack.
Note: The gure above is for illustrative purposes only. Always install servers to
the bottom of the rack rst.
Caution: Do not pick up the server with the front handles. They are designed
to pull the system from a rack only.