Sutron INTEGRA-TR User manual

INTEGRA-TR INTEGRATED WIRELESS MODEM
VHF 132-174 MHZ
UHF 380-512 MHZ
900 MAS 928-960 MHZ
SUTRON PART NUMBER 6661-1249-1
APPLICATION NOTE
PREPARED BY:
INTEGRATED SYSTEMS DIVISION
2009

APPLICATIONNOTE
Integra-T R Integrated Modem
i
TABLE OF CONTENTS
1.................................................INTRODUCTION 1
2........................PROGRAMMING THE RADIO 2
3...................... SERIAL PORT CONNECTIONS 9
3.1 INTEGRA WITH 9210.........................................9
3.2 INTEGRA WITH 8210........................................9
4.......................RADIO SETTINGS & TESTING 10
4.1 XLITE................................................................ 10
4.2 XCONNECT ...................................................... 13
5................................ INTERFACE DEFINITION 16
5.1 INTEGRA-TR DATA INTERFACE ....................... 16
5.2 9210 COM PORT INFO ................................... 16
6. INTEGRA TR TECHNICAL SPECIFICATIONS 17

APPLICATIONNOTE
Integra-T R Integrated Modem
1
1. Introduction
The Dataradio Integra-TR integrated wireless modem provides advanced features without complicated
system setup. Designed specifically for data transmission, this programmable, transparent modem
transmits data real-time without delays at speeds up to 19.2 kbps. With enhanced diagnostics it is the
perfect choice even in the harshest environments.
Features:
Supports Data Activated Transmit (DOX) or RTS/CTS flow control
On-line Radio Network Diagnostics to monitor and maintain your communications link
Diagnostic output supports OPC Enabled Diagnostics feature
User selectable data rates:
o6.25 kHz: 4800 bps
o12.5 kHz: 4800 or 9600 bps
o25 kHz: 4800, 9600, or 19200 bps
Separate Application and Setup/diagnostics ports
Prevents transmission of any extraneous data bits
Approved for Non-Incendiary (Class 1, Division 2) by Factory Mutual
Low power consumption mode:
oVariable Output Power
Front panel LEDs
One piece integrated design
DIN-rail mount options available
Two-year limited factory warranty

APPLICATIONNOTE
Integra-T R Integrated Modem
2
2. Programming the Radio
Download the programming software from the following link.
http://www.dataradio.com/4_2.html
Proceed with the following steps to program the radio.
a. Connect the power connector on the back of the radio. Also, connect the 5W load resistor and
rubber duck antenna to the RF port of the radio.
b. Connect the red & black wire of the power connector to the +12 Volt & GND of power supply,
respectively.
c. Connect the 9-pin serial cable from computer’s COM port to the Setup Port of the Radio.
d. Start the IntegraTR Program on your PC. The following screen will appear.

APPLICATIONNOTE
Integra-T R Integrated Modem
3
Figure 1. IntegraTR Programmer main window
e. Click on the Read toolbar button on the screen. This step will update the program with the latest
settings in the radio.
f. From the main menu, select Utilities|Port Settings (Figure 2. Port Settings window).

APPLICATIONNOTE
Integra-T R Integrated Modem
4
Figure 2. Port Settings window
g. Make sure your settings match the settings above in Figure 2; if not, make any necessary changes.
Click OK when finished. Never change the Baud Rate in the Port Settings window. This baud
rate is just for your PC to talk to the radio.

APPLICATIONNOTE
Integra-T R Integrated Modem
5
h. Click on the Parms toolbar button in the main window. Figure 3. Modem parameters setup
window will appear. Make sure the Modem tab is selected. Select the Network Speed. For
8210/9210s select 9600 Half Chan if you have one frequency for TX and RX. If you have separate TX
and RX frequencies, select [XXXX]. For details on these settings, please see the INTEGRA technical
manual section 2.4.4.1.
Figure 3. Modem parameters setup window

APPLICATIONNOTE
Integra-T R Integrated Modem
6
i. Next, click on the Com/Analog tab in the Modem/Radio Parameters window (Figure 4). Select the
desired radio communications baud rate. For details on these settings, please see the INTEGRA
technical manual section 2.4.4.3.
Figure 4. Com/analog parameters setup window

APPLICATIONNOTE
Integra-T R Integrated Modem
7
j. Lastly, click on the Radio Tab to program the frequency (Figure 4). Enter the RX/TX frequencies and
the power. A power value of 255 is equivalent to 5 W power. Click OK to save all parameter settings.
For details on these settings, please see the INTEGRA technical manual section 2.4.4.4
Figure 5. Radio parameters setup window
k. Click Write toolbar button in the main window to write all the settings to the radio. Figure 6 will
appear at the beginning of the writing process. Click OK to proceed

APPLICATIONNOTE
Integra-T R Integrated Modem
8
Figure 6. Write in progress window
l. After the programming is done the window will go blank and Figure 7 will appear. Disconnect the
programming cable from you radio. The radio is now programmed.
Figure 7. Program complete window