bolid RS-FX-MM User manual

1
SERIAL RS-232 / RS-422 / RS-485 FIBER OPTIC MODEM
RS-FX-MM, RS-FX-SM40
OPERATIONS MANUAL
1DESCRIPTION AND OPERATION
1.1 Product Purpose
1.1.1 RS-FX-MM / RS-FX-SM40 Serial RS-232 / RS-422 / RS-485 Fiber Optic Modem (hereinafter
referred to as the modem) is designed to convert a standard RS232 / RS485 / RS422 signal to a fiber optic
link to extend the signal up to 40 Km.
1.1.2 The modem is intended for round-the-clock operation.
1.1.3 The modem is classed as non-repairable and periodically serviced equipment.
1.1.4 The modem’s design doesn’t imply operating it in aggressive and dusty environments or in
explosion and fire hazardous premises.
1.2 Specifications
Table 1.2.1
Parameter Value
1.2.1 Power input 1
1.2.2 Power supply voltage 12 through 48 Vdc
1.2.3 Power rate 5 W max
1.2.4 Start-up time 10 s
1.2.5 Data rates 300 through 115200 bps
1.2.6 Fiber range: - RS-FX-MM
- RS-FX-SM40
2 km
40 km
1.2.7 Fiber optic cable: - RS-FX-MM
- RS-FX-SM40
Multi-mode 50/125
µ
m
Single-mode 9/125 µm
1.2.8 Fiber connector SC/PC
1.2.9 Optic wavelength 1,310 nm
1.2.10 Serial range: - RS-232
- RS-422, RS-485
15 m
1,000 m
1.2.11 Orion ISS devices per a single RS-485 interface bus 127 max
1.2.12 Enclosure protection degree as per GOST 14254-2015 IP20
1.2.13 Resistance to mechanical exposure as per OST 25 1099-83 Arrangement Category III
1.2.14 Vibration exposure: - Frequency range
- Max acceleration
1-35 Hz
0.5 g
1.2.15 Environmental category as per OST 25 1099-83 О3
1.2.16 Operation Temperature Minus 30 to + 55°С
1.2.17 Weight 0.3 kg max
1.2.18 Overall dimensions 95
×
70
×
29 mm
1.2.19 Non-stop operation 24/7
1.2.20 MTBF 80,000 h min
1.2.21 Survival probability 0.98758
1.2.22 Expected service life 10 years
1.2.23 In terms of immunity to electromagnetic interference, the equipment meets the requirements of
Test Severity Level III as per the relevant standards listed in Appendix ‘Б’ to GOST R 53325-2012.

2
1.2.24 The equipment passes the industrial interference standards prescribed for Class ‘Б’ equipment as
per GOST R 30805.22.
1.2.25 The modems are to be powered from battery backed power supplies RIP-12 or RIP-24 (of series
approved by Fire Certificates) that send faults occurred in the power supply line to an alarm loop of a
control and indicating equipment (such as Signal-10, Signal-20М, Signal-20P) or to the network controller
(S2000Мcontrol panel or Orion Pro Software Suite).
1.3 Scope of Delivery
The modem comes along with the parts shown in Table 1.3.1.
Table 1.3.1
Item Q-ty, pcs.
RS-FX-MM
RS-FX-SM40 1
Operations Manual 1
Resistor С2-33Н-0.25-620 Ohm 5% 3
Wall Mount Bracket 1
Screw 2
Wall plug 2
2INTENDED USE
2.1 The design of the modem meets the requirements of fire and electrical safety including operation in
emergency in accordance with GOST 12.2.007.0-75 and GOST 12.1.004-91.
2.2 Do shut off the mains power from the modem before mounting, installing, and maintaining this one.
2.3 Operating restrictions, design, mounting, connecting, settings, testing and operation
procedures for the modem are defined in details in its User’s Manual (the full version),
which is available online at bolid.ru in the section Products on the page of
RS-FX-MM, RS-FX-SM40 and in the mobile app ‘Mobile Product Catalogue’
https://bolid.ru/support/mobile-catalogue/.
2.4 If a technical failure of the modem has been found, the equipment shall be taken out of operation and
sent for repair in accordance with Section 4.
3MAINTENANCE
3.1 The modem shall be maintained by persons qualified for Accident Prevention of Level II or higher.
3.2 The maintenance procedures to be performed are described in RS-FX-MM / RS-FX-SM40 User’s
Manual (the full version, please see Section 2.3 of this manual).
4REPAIR
4.1 Repair of faulty equipment is to be performed by the manufacturer or in authorized repair centers. The
equipment shall be sent for repair in compliance with Company Standard QMS 8.5.3-2015, which can be
found online at our website https://bolid.ru/support/remont/.
Attention!
The equipment shall be submitted for repair being assembled and clean and along with all
the parts listed in the technical documentation.
Claims are accepted only if a reclamation report describing the problem is applied to the
submitted equipment.

3
4.2 A product’s failure resulted from consumer’s not observing rules of mounting and operation is not a
reason for claims and warranty repair.
4.3 Claims should be submitted to the following address:
NVP BOLID, #4 Pionerskaya Str., Korolyov, Moscow Region, 141070, Russia
Phone/fax: [phone] (PBX). E-mail: [email protected].
4.4 In case of any issue related to use of the product, please contact the technical support: +7 (495) 775-
71-55 or e-mail: [email protected].
5STORAGE
5.1 In a transport container the equipment can be stored at ambient temperatures -50°Сthrough +50°С
and relative humidity up to 95% at +35°С.
5.2 In the consumer package the equipment shall be stored only in heated premises at temperatures +5°С
through +40°Сand relative humidity up to 80% at +20°С.
6TRANSPORTING
6.1 The modem can be transported in a transport package at ambient temperatures minus 50 through
+50°Сand relative humidity up to 95 % at +35 °С.
7DISPOSAL
7.1 The equipment is to be disposed of considering that there are no toxic components in it.
7.2 The content of precious materials: does not require accountability for storage, retirement and disposal
(Clause 1.2 of GOST 2.608-78).
7.3 The content of non-ferrous metals: does not require accountability for retirement and further disposal.
8MANUFACTURER WARRANTY
8.1 The manufacturer guaranties the product meets with technical requirements stated in the manuals if
the user follows the instructions for transportation, storage, installation, and usage.
8.2 The warranty period is 18 months since putting the product into operation but no more than
24 months from the manufacturer’s date of production.
9CERTIFICATES INFORMATION
For certificates information, please refer to RS-FX-MM / RS-FX-SM40 User’s Manual (the full
version, please see Section 2.3 of this manual).
10 ACCEPTANCE AND PACKAGING CERTIFICATE
Product
Factory Number
Packed By
Date, Month, Year
RS-FX-MM
RS-FX-SM40
is manufactured, accepted in line with mandatory requirements of national standards and applicable
technical documentation, approved as ready for use, and packaged by the Bolid Company.