Svantek SV 103 User manual

SV103
Hand-Arm
Vibration
Dosimeter
User Guide

The SV 103 measures the A(8) vibration exposure in accordance with the ISO 5349-2 and
European 2002/44/EC both in m/s2and points. The instrument significantly decreases the
measurement uncertainty related to the estimation of daily exposure time as it is small enough
to take daily vibration exposure measurements without interfering with normal working
activities. The SV 103 uses the SV 107 moulded hand-held adaptor with the tri-
axial MEMS accelerometer and contact force sensors. The MEMS technology means the
SV 107 is extremely robust, shock resistant, uses very low power and is free of the
DC-shift effect that adversely affects systems based on piezoelectric accelerometers.
ISO 5349-2 and EU Directive 2002/44/EC
List of Contents
Page 3 CONTENTS OF THE SV 103 BOX
Page 4 CONFIGURATION WITH SUPERVISOR SOFTWARE
Page 5 IN-SITU CHECK WITH SV110
Page 6 RUNNING THE MEASUREMENT
Page 7 DATA DOWNLOAD
Page 8 SUPPORT AND SERVICE
Page 9 TECHNICAL SPECIFICATION
2
SV 103 User Guide

List of optional extras not included in the SV 103 box
Hardware accessories:
Part name Description Applications
SA 76 Waterproof carrying case Transportation
SA 105A Calibration adapter Periodical verication, in-situ checks
SV 110 Hand-held vibration calibrator Instrument check before and after series
of measurements
SV111 Vibration calibrator Instrument check before and after series
of measurements
Software options that can be activated by code
(with no need to return the meter to factory):
Part name Description Applications
SF 103 3OCT 1/1 & 1/3 octave analysis Verication of vibration sources
Research and development
SF 103 WAV Time domain signal recording
during measurement - continuous or
triggered
Analysis of vibration signal
Post-processing
Research and development
Accredited calibration
(requires sending the instrument to SVANTEK authorised laboratory)
SV_CV_HA_T Accredited calibration for vibration
meter
ISO / IEC 17025 calibration certicate
List of contents included in the SV 103 box:
Please check the list against the contents. If any of the listed items are missing,
please contact your local Svantek distributor or send an e-mail to
of[email protected] within 3 days of receiving the parcel.
3
SV 103 User Guide
Hardware accessories:
Lp. Description pcs.
1. SV 103 Vibration dosimeter 1
2. SV 107 Tri-axial accelerometer (connected to SV 103) 1
SA 150 Adapter to SV 107 1
SA 151 Adapter to SV 107 (connected to SV 107) 1
SA 152 Adapter to SV 107 1
3. SA 103 Armband for SV 103 1
SA 107 Wristband for SV 107 cable 2
4. SC 156 USB cable 1
5. SA 54 charger/power supply with adapters 1
6. SA 153 Foce calibration adapter 1
7. Spare screws for xing SA 151/152/153 adapters do SV107 2
Screwdriver 1
8. CD with user manual 1
9. Factory calibration certicate 1
10. Warranty card 1
11. Information card 2
1
2
5
3
5
4
7
6

Configuration with Supervisor software
1) To switch the power on hold the <ENTER> button for a couple
of seconds.
Configuration set-up
5) Download current Settings from Instrument files to Local Files using right
arrow and edit SV103 settings using panels on the right hand side
8) Disconnect the USB cable. Instrument is ready to measure.
SV 103 User Guide
4
2) Connect the USB cable to PC. Make sure the Supervisor
software and USB drivers are previously installed on the PC.
6) Save settings file under new name
7) Upload the file to the Instrument Files using left arrow and select Apply
3) Open the Supervisor software and go to the Instrument tab.
4) Select Settings

In-situ check with SV 110
1) Unscrew the SA 151 adapter from the SV 107 sensor
2) Mount the SA 105A adapter on the SV 110 hand-held calibrator*.
Using magnets connect the SV 107 to SA 105A.
Installation of SV107 on the calibrator
5) Start the calibrator using level of 10 m/s2at 80 Hz and wait until all LEDs
are green.
6) Press Enter on SV 103 to start the check procedure.
7) Repeat the procedure for all 3 axes.
SV 103 User Guide
5
4) Enable Calibration menu in SV 103 by holding Right Arrow button.
Select the System check and axis.
*SV110 calibrator and SA105A adapter are not the part of the SV103 kit. They need to be ordered additionally.

Running the measurement
1) Connect one of the adapters to SV 107 sensor using the screw.
It is mandatory to use a screw for measurements.
Set up of SV 103
5) To start the measurement manually pres 2 arrows simultaneously.
SV 103 User Guide
6
4) Place the SV 107 on the palm of the hand as shown below. Secure the
cable on a wrist with a wrist band.
2) Put the mounting adapter on arm and place the SV 103 in it.

Data files download
1) Connect the SV103 to PC and open Supervisor software.
Click the Download button located next to Settings and Inventory.
Downloading with Supervisor
4) The file will open in default panels.
SV 103 User Guide
7
2) Select files you wish to download and click the Download button
located in the bottom section.
3) Once the file is downloaded it will be automatically shown in the Data
Browser. Right click on file and start "New session" or simply double click
on file
5) The detailed information on the operations within the Session panels is
described in the SV 103 User Manual and Supervisor Software Manual.

Should your SVANTEK professional measurement equipment need to
be returned for repair or for calibration, please contact the service
office at the following number or contact via the SVANTEK’s website.
Service Office: [phone] or [phone].
Office hours are 9:00 a.m. to 5:00 p.m. Central European Time.
-E-mail at [email protected]
-Internet at www.svantek.com
-Address:
SVANTEK Sp. z o.o.
Strzygłowska 81
04-872 Warszawa,
Poland
SV 103 User Guide
8
Support and service

SVANTEK Sp. z o. o.
ul. Strzygłowska 81, 04-872 WARSAW, POLAND
phone/fax [phone]
http://www.svantek.com e-mail: [email protected]
Proudly distributed by:
SV 103 User Guide
SV103 Technical Specification
The policy of our company is to continually innovate and develop our products.
Therefore, we reserve the right to change the specifications without prior notice.
Application Hand-arm
Standards ISO 8041:2005, ISO 5349-1:2001; ISO 5349-2:2001;
Meter Mode ahw (RMS), ahv (VECTOR), Max, Peak, Peak-Peak
A(8) Daily Exposure, ELV Time (TIME LEFT TO LIMIT),
EAV Time (TIME LEFT TO ACTION)
Filters Wh(ISO 5349) and corresponding Band Limiting filter
RMS & RMQ Detectors Digital true RMS detector with Peak detection, resolution 0.1 dB
Measurement Range 0.2 ms-2 RMS ÷ 2000 ms-2 PEAK
Frequency Range 1 Hz ÷ 2000 Hz
Data Logger Time-history data including meter mode results and spectra
Time-Domain Recording Simultaneous 3-channel time-domain signal recording (option)
Analyser 1/1 octave real-time analysis (option)
1/3 octave real-time analysis (option)
Accelerometer Detachable SV 107 tri-axial accelerometer with hand straps in accordance to ISO 5349
Display OLED 128 x 32 pixels
Memory 8 GB
Interfaces USB 2.0 client, Bluetooth
Keyboard 4 push buttons
Power Supply
Ni-MH rechargeable cells operation time > 24 hours1
USB interface 500 mA HUB
Environmental Conditions
Temperature from -10 oC to 50 oC
Humidity up to 90 % RH, non-condensed
Dimensions 88 x 49.5 x 19.2 mm (instrument without accelerometer, cable and mounting stripe)
Weight 150-160 grams with SV 107 accelerometer and one of
vibration contact adapters
1dependent on instrument operation configuration