SvoëMesto Kayfun Lite User manual

Kayfun [lite]
Kayfun [lite]
MANUAL
1. Before use
The SvoëMesto Kayfun Lite is a rebuildable tank atomizer specifically designed to vaporize e‐liquid for
electronic cigarees. Before use you must install a coil intended for use in electronic cigarees. It is re‐
commended to clean the device with water, dry and lube all visible o‐rings with e‐liquid.
This manual is meant as a brief overview on the general funconality of the SvoëMesto Kayfun Lite. If
you have no experience using a rebuildable atomizer or creang coils, please consult your local vendor.
Further informaon and languages at www.svoemesto.de.
2. Applicaon
The SvoëMesto Kayfun Lite’s recommended use is for coils with a minimum resistance of 0.5 ohm and an
electric input from 5 to 25 was. Please use the atomizer responsibly and the coils you’ve created at your
own risk. Instrucons for use.
2.1 Accessing the deck
2.2 Installing coil and wick
ATTENTION: Please exclusively use materials that are designed to be used in electronic cigarees.
The coil is placed diagonally between the build screws and approx. 1.5 mm – 2 mm above the air outlet,
so that air can smoothly flow around the coil. The ends of the wire are placed under the build screws
and then clamped underneath them.
The overhanging ends of the wick should be placed in the
empty spaces beneath the terminals, so that they lay above
the liquid channels. Before assembling the atomizer, it is
recommended to saturate the wick with e‐liquid.
Step 1
Flip the atomizer upside
down, if the tank is filled.
Step 2
Unscrew the base
counter‐clockwise
Step 3
Remove the base to
access the deck.
ATTENTION
For your own safety please note the
following
The coil has to be connected with one
end at the plus terminal, with the
other end at the minus terminal.
The exceeding ends of the wire have
to be cut flush with the terminals and
must not sck out of the build deck.
Otherwise, this may cause a short
circuit.
The coil must not touch the deck itself.

Kayfun [lite]
Kayfun [lite]
MANUAL
2.3. Seng airflow
The Kayfun Lite has connuously adjustable airflow control.
2.4. Filling
Aenon: Please exclusively use e‐liquids designed for electronic cigarees. For filling the Kayfun Lite
has to be assembled completely.
3. Warranty
The manufacturer’s warranty is one year on all stainless steel parts. Excluded from warranty are all plasc
components such as tanks and insulators, glass tanks and o‐rings.
4. Disclaimer
With the SvoëMesto Kayfun Lite, please use original SvoëMesto accessories only. The manufacturer accepts
no liability for any third‐party accessories or issues which may have been caused or exacerbated by their use.
5. Warnings
Before use please read the manual carefully!
Please keep the atomizer dry!
Do not use the atomizer for other purposes than intended!
Connect the atomizer to a power source that is suitable for its intended use!
Using the atomizer on high voltages or without a fluid can damage the atomizer. The manufacturer
accepts no liability for atomizers that were damaged during use.
Using the atomizer incorrectly not only can lead to a defect of the atomizer, but also cause fire.
Keep the atomizer away from heat sources.
Not suitable for children. Please keep the atomizer away from children!
Step 1
Flip the atomizer
upside down.
Step 2
Unscrew the base
counter‐clockwise
Step 3
Fill the tank from the boom
through the liquid channels.
Step 1
Insert a small flathead screwdriver into the 510 connector
in the boom. While fully assembled, put the Kayfun Lite
with the mouthpiece to your lips and draw on it.
Step 2
Turn the screw inside the 510 connector
clockwise to ghten the airflow or
counter‐clockwise to loosen it.