Swann Xtreem User manual

1
EN
Xtreem®Security Camera
Cámara de seguridad Xtreem®
Caméra de sécurité XtreemMD
Telecamera di sicurezza Xtreem®
Xtreem®Überwachungskamera
EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide
IT Guida rapida DE Schnellstartanleitung

2
EN
CAMERA OVERVIEW
Passive infrared
motion sensor
Threaded mounting hole
(for optional screw-in stand accessory)
Pull rubber cover gently from the
bottom to access:
- Set (mini) button
- Reset button
- microSD card slot
LED indicator
Set button
Night detection
sensor
Micro USB
charging port
Speaker
QR code
(for device pairing)
Microphone
Remove protective film covering the front of
the camera before use
Note: Keep the top and bottom rubber covers closed when
not in use to prevent water and dust from getting in.
Infrared LEDs
(for night vision)

3
EN
GETTING STARTED
Before using the camera for the first time, charge it for at least two hours with the included micro USB
charging cable.
1Lift the rubber cover of the micro USB port on the bottom of the camera.
2Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.
3Insert the larger end of the micro USB charging cable into a USB wall charger such as the USB
power adapter that came with your smartphone.
4The LED indicator on the front of the camera turns solid blue indicating that the camera is
charging. When the camera is fully charged, the LED indicator will turn off.
5Actual charging times may vary depending on the USB power supply (DC5V 2.1A is recommended
for faster charging) and the remaining battery level. A full charge may take up to 11 hours (due to
the camera’s large battery capacity).
Note Once you have set up your camera, you can easily track the charging progress (%) using the app.
A microSD card is required for the camera to record events. Depending on the model purchased, your
camera will come with a pre-installed 16GB or 32GB microSD card. You can easily replace the microSD
card with a new one (up to 128GB, minimum Class 10 recommended) if needed in the future. Simply lift
the rubber cover on the top of the camera, eject the current microSD card (push in until it clicks) from
the microSD card slot and then replace with another microSD card (with the label side facing the back
of the camera). Format any microSD card being used with the camera for the first time using the app.
Charging the camera
Installing the microSD card

4
EN
GET THE SWANN SECURITY APP
1Download the latest version of the Swann Security app from the Apple App Store® or Google
Play™ Store on your iOS or Android device. Simply search for "Swann Security".
2Open the app and create your Swann Security account by tapping “Not yet registered? Sign
Up” at the bottom of the screen. Then, activate your Swann Security account by confirming the
verification email that is sent to the registered email address.

5
EN
Launch the Swann Security app and sign in. Tap the Pair Device button on the screen (or tap the menu
icon in the top left and select “Pair Device”) and follow the in-app instructions to set up your new
camera. Before you begin, have the camera with you, be close to your router, and have your Wi-Fi
network information (including password) handy. Please note that the camera can connect to a 2.4GHz
Wi-Fi network only.
SET UP THE CAMERA

6
EN
The camera can be conveniently placed on a table or shelf, or mounted on the wall using the magnetic
stand (supplied) or the screw-in stand (optional accessory which can be purchased separately). Because
the camera is completely wire-free, you’ll have a lot of flexibility on where you can put it. Choose a
location with strong, reliable Wi-Fi reception to ensure best video streaming and battery performance.
As a general rule, the nearer your camera is to your router, the better the wireless connection quality.
CAMERA PLACEMENT
C. With double-sided mounting tape (For indoor use only)
Do not use on rough surfaces. Works best on smooth, dry surfaces (use rubbing alcohol
to clean surface, making sure it is cleared of any dirt).
Peel off liner on one side of the supplied mounting tape and apply it to the back of the
magnetic stand.
Peel off opposite liner then using a firm amount of pressure, press the magnetic stand
against the surface for 60 seconds. Allow 24 hours for the adhesive to fully cure before
attaching the camera onto the magnetic stand.
Mounting the magnetic stand
A. With screws (Recommended method
for permanent mounting)
Remove the rubber pads to reveal screw
holes. Then attach the magnetic stand to
the surface using supplied screws (2.8mm x
21.6mm) and plugs (if mounting on drywall
or concrete). Reinsert the rubber pads.
B. With keyhole slot
There is a keyhole slot on the
back of the magnetic stand
where a screw fits for hanging
on the wall. Insert screw (4mm
x 18.2mm) and plug (if mounting
on drywall or concrete) into the
mounting point, leaving a bit
of gap between the wall and
the screw head. Then fit the
magnetic stand over the screw
head through the keyhole slot
and slide down to make sure it
sits securely.
IMPORTANT: Ensure that the surface and fixing points
are strong enough to sustain the weight of the camera
and magnetic stand.

7
EN
Have questions?
Visit our Support Center at support.swann.com.You can register your product for dedicated technical
support, find troubleshooting articles, and more. Or email us at any time via: [email protected]
HELP AND RESOURCES
Motion detection
The camera’s PIR motion sensor detects heat signatures of moving objects. You’ll generally get good
detection results by pointing the camera downwards at an angle where people will be moving across
the coverage area before heading directly towards the camera. You can turn motion detection on or off,
as well as adjust the sensitivity using the Swann Security app.
LED indicator guide
The LED light on the front of your camera helps inform you of what is happening with the device.
Swann Security app manual
While using the Swann Security app, you can access the Swann Security app manual (Menu > User
Manual) at any time to learn more about using the app to view live video, playback event clips as well
as customize various camera settings including camera name, sleep period, and motion sensitivity.
Rebooting the camera
On rare occasions, it might be necessary to reboot your camera if it becomes unresponsive. A simple
reboot can also fix connectivity issues quickly. Using a paper clip, press and release the Reset button.
This powers off the camera. Then briefly press the SET button (for 1 second) to reboot the camera.
Solid Blue USB Charging
Solid Red Live streaming / Motion recording
Slow Blinking Blue Wi-Fi Pairing mode
Fast Blinking Blue Connecting to Wi-Fi
Infrared LEDs Blinking Firmware update in progress