Swann A856 User manual

Professional HD
A856 Dome Camera
For use with Swann 4600 Series HD DVRs
EN INSTRUCTION MANUAL

1
Introduction
Congratulations on your purchase of this Profes-
sional HD A856 Dome Camera.
• A state of the art surveillance camera with
1080p video technology
• Seeing is believing with 1080p HD Cameras
(2 Megapixel) perfect for most locations
around home or business
• Latest infrared cut filter for amazing night vi-
sion to 82ft/25m for clarity in low light
• Sturdy polycarbonate camera construction
suits indoor & outdoor applications with IP66
rating for any weather conditions
• Deter thieves, safeguard loved ones, protect
your property & cut the cost of crime with
this professional surveillance camera from
Swann
Important instructions
1. Make sure the camera is fixed correctly and sta-
ble if fastened in place.
2. Only use the supplied power adapter (12V).
3. For use with Swann’s DVR4-4600, DVR8-4600 or
DVR16-4600 digital video recorders only.
Please note - Have a look at the camera location
tips included with your DVR, to select the best lo-
cation for your camera (the camera location tips
provided here are for general purpose only).
Important note - All jurisdictions have specific
laws and regulations relating to the use of cam-
eras. Before using any camera for any purpose,
it is the buyer’s responsibility to be aware of all
applicable laws and regulations that prohibit or
limit the use of cameras.

2
Connecting your Camera
1. Connect the Video Output and Power Input
connections on the camera to the corresponding
connections on the supplied Video & Power Cable.
Connect the video output on the Video & Power cable
to a spare video input on the DVR.
2. Connect the supplied Power Adapter to the power
input on the Video & Power Cable then connect the
Power Adapter to a spare wall socket. Press the wall
socket’s switch to the on position to supply power to
the camera.
Power Input
Video Output
Twist to lock
video connectors
Video Input
Video & Power Cable
Connect this to the DVR
Power Adapter
connects here
Power Output
Power Adapter
Connect to a spare
wall socket
PTZ
75 3 1
86 4 2
eSATA
HDMI LAN & USB B A DC 12V
IN
VGAVIDEO IN AUDIO OUT
AUDIO IN
1
2
Digital Video Recorder
Dome Camera

3
Mounting the Camera
To mount the camera
1. The camera can be mounted onto a flat, vertical or
horizontal surface and must have sufficient strength
to hold the camera. Materials such as hardwood,
brick or masonry are good options.
2. Loosen the three screws located at the base of the
camera then remove the bracket cover and dome
cover.
3. Position the camera in the location you want to
mount it then mark the screw holes on the surface to
position the screws. Using the appropriate screws for
the surface you are mounting to, screw the bracket
into place.
4. If you’re mounting to a wooden surface, screw the
camera directly to the surface.
5. When mounting to a masonry surface, you’ll need
to use the included wall plugs.
Aiming the camera
1. Replace the dome cover and bracket cover.
2. The dome cover can be rotated left or right.
3. The camera can be aimed in almost any direction
from wherever you choose to mount it.
4. After you’ve finished adjusting the camera’s viewing
position, tighten each screw to lock the position in
place.
Positioning the cables
1. When running the cable, try to avoid bending it at
sharp angles.
2. Avoid positioning the cable live electrical wiring. AC
electricity generates radio noise which can interfere
with the signal from your camera.
3. Do not stretch or apply force to the cable greater
than 25lbs/11kgs.

4
Camera Location Tips
Some things to consider when choosing a location -
1. What you want to monitor and where you’ll get the
best view of it.
2. How you’re going to connect the camera to your
monitoring system; remember that cables and
connections should be kept out of the weather.
3. How to keep the camera out of harm’s way. It’s
recommended to mount your cameras at an elevated
position.
4. Place your camera as close to the area of interest
as practicable. The best position is from about 4m
(13ft) above looking slightly down, keeping in mind the
details you are looking for.
5. Although the sky looks nice when you look at the
live view from your camera, it is an unlikely direction
for an offender to approach, make sure your camera
has minimal sky in it as the light in daylight can make
the foreground of the image darker.
6. Think about the most likely way a potential offender
may approach your home, use your cameras to give
you the best coverage of these areas.
7. The camera’s casing is resistant to water, different
weather conditions and tampering. It would take
an overwhelming event of this kind to damage the
housing of the camera. However, the cable and
connector are vulnerable and require protection.
8. Even though the camera is weather and water-
resistant, prolonged exposure to adverse weather
conditions such as sunlight or excessive moisture,
may eventually damage the internal components of
the camera and adversely affect its performance.
9. When running your cable, try to avoid bending it at
sharp angles.
10. Don’t put your cable near live electrical wiring.
AC electricity generates radio “noise” which can
interfere with the signal from your camera.

5
Limited Warranty - Terms & Conditions
Swann Communications warrants this product
against defects in workmanship and material for
a period of one (1) year from its original purchase
date. You must present your receipt as proof of
purchase for warranty validation. Any unit which
proves defective during the stated period will be
repaired without charge for parts or labour or re-
placed at the sole discretion of Swann. The end
user is responsible for all freight charges incurred
to send the product to Swann’s repair centres. The
end user is responsible for all shipping costs in-
curred when shipping from and to any country
other than the country of origin.
The warranty does not cover any incidental, acci-
dental or consequential damages arising from the
use of or the inability to use this product. Any costs
associated with the fitting or removal of this prod-
uct by a tradesman or other person or any other
costs associated with its use are the responsibility
of the end user. This warranty applies to the origi-
nal purchaser of the product only and is not trans-
ferable to any third party. Unauthorized end user
or third party modifications to any component will
render all warranties void. By law some countries
do not allow limitations on certain exclusions in
this warranty. Where applicable by local laws,
regulations and legal rights will take precedence.
For Australia: Our goods come with guarantees
which cannot be excluded under Australian Con-
sumer Law. You are entitled to a replacement
or refund for a major failure and for compensa-
tion for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of ac-
ceptable quality.

6
FCC Verification
This equipment has been tested and found to comply with the limits for Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected
• Consult the dealer or an experienced radio/TV technician for help
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) These devices may not cause harmful interference.
(2) These devices must accept any interference received, including interference that may cause unde-
sired operation.

MA856CAM070815E | © Swann 2015
Helpdesk/Technical Support
Technical Support E-mail: [email protected]
Telephone Helpdesk
USA Toll Free 1-800-627-2799
USA Parts & Warranty 1-800-627-2799
(M-F, 9am-5pm US PT)
AUSTRALIA 1800 788 210
NEW ZEALAND Toll Free 0800 479 266
UK 0808 168 9031