Swann One User manual

At a Glance
Thank you for choosing the SwannOne™ Window/Door Sensor. The SwannOne
Window/Door Sensor monitors the opening and closing of doors and windows, notifying
you when changes occur via the SwannOne system.
Magnet 3M Command™
Mounting Strips
Sensor QSGWS150615E
Key Fob
Indoor
Camera
Outdoor
Camera
Smart Plug
Motion
Sensor
Door/Window
Sensor
Indoor
Siren
Outdoor Siren
Zen
Thermostat™
Smart
Hub
Discover More SwannOne Smart Home Solutions
EN
Quick Start Guide
Window/Door
Sensor
At a Glance Compliance Information
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1)This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
Disposal and Recycling Information
Correct Disposal of this product. This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device,
please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environment safe recycling.
Battery Safety Information
CAUTION: KEEP BATTERIES AWAY FROM SMALL CHILDREN. RISK OF
EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES PROMPTLY IN ACCORDANCE WITH LOCAL REGULATIONS.
Status
LED
© Swann Communications 2015
www.swannone.com
READ ME
FIRST

AAA
AAA
AAA
AAA
AAA
AAA
Activate Pair Mount Need Help?
Plastic
Strip
Connect
Button
LED
1Open the sensor by pushing back the
release catch on top. The front panel
should come off easily.
2Remove the protective plastic strip to
engage the battery and activate the
sensor.
1Before applying Command™ Strips,
clean the surface where the sensor and
magnet will be mounted, and make sure
it is dry.
2Fit the sensor and magnet with
appropriate sized strips, and then press
the sensor and magnet firmly onto
surface for 30 seconds.
3Test the sensor by opening and closing
the window/door. The Status LED blinks
whenever movement is detected. You
should also receive a status alert via the
SwannOne web dashboard and app on
your smartphone.
Get more information regarding the setup and use of your product on the web at
swannone.com, or contact our multi-lingual support team anytime via:
Take time to choose the location and test orientation of the sensor and magnet.
The sensor and magnet should ideally be positioned in a way that when the
window/door is closed, they are aligned side by side, within 5/16" from each other.
If the sensor is not connecting as expected, perform a sensor reset by pressing
and holding the Connect button until the status LED blinks rapidly, and then try
pairing the sensor again. Placement Examples
[email protected]
USA & Canada 1800 627 2799
UK & Europe 0808 168 9031
Australia 1800 788 210
New Zealand 0800 479 266
Connect
Button
SwannOne Warranty
Your SwannOne products are backed by a full 12 month guarantee from the date of
purchase. In the unlikely event of anything going wrong, you can have confidence that
your purchase is protected. Refer to swannone.com for terms and conditions.
1Sign in to your SwannOne account at
home.swannone.com.
2From your web account dashboard, go to
My Devices > Window/Door Sensors and add a
device.
3When the Setup page appears, put your Smart
Hub in pairing mode by selecting Learn devices.
4Press the Connect button on the sensor. The
status LED blinks once. When pairing is complete,
the status LED blinks twice.
Check the Setup page to confirm the sensor was
paired successfully, and then finish the setup
process by following the on-screen instructions.