switel DT-100 User manual

MA-600 is a plug-in receiver, it can carry two wireless transmitters
such as doorbell buttons with two distinguishable flash pattern.
The first coded transmitter will flash rapidly; the second coded
transmitter flashes slower. Step 1: Press & Hold the Learn button
fo r 3 se co nd s. Th e re d L E D
indicator inside the lens will blink.
(if the red LED indicator lights
c o n s t a n t l y t h a t m e a n s t h e
memory of the receiver is full.
Please see section 3)
Step 2: Press the Melody selector button ♫
to scroll through the melodies.
Once you hear a melody you
prefer, do not press any button as
t h e m e l o d y i s s e t f o r t h a t
transmitter.
Step 3: Once the melody is selected, trigger the transmitter to
pair. If successful, the receiver (chime unit) will
generate a short tone. Press the Learn selector
button to exit the pairing mode, the system is now
ready to use.
PARTS & FUNCTION
MOUNTING & POWER
Flasher Indicator
Function
switch
Speaker
Melody
button
Learn
button
Wall plug
(AC plug)
Press & hold the Learn button for 3 seconds to enter the pairing
mode. Press the Learn button to scroll between 1 and 2
transmitters , press the Melody selector repeatedly until you ♫
have found the desired melody.
Trigger the transmitter to confirm the melody, when you hear a
twice short tone press the Learn button to exit.
1. ASSIGNMENT OF THE TRANSMITTER
3. CLEAR THE TRANSMITTER FROM THE RECEIVER
MEMORY
Press & hold the Learn button for 3 seconds to enter the
pairing mode. Press & hold both the Learn button & the ♫
Melody selector together for 3 seconds to delete the memory.
The re ceiv er wil l g ene r ate a be e p tone to in dica te all
transmitters on the memory is deleted. The red L E D will change
to blink. Now you can pair the new transmitters to the receiver
as per the previous section.
Melody
Learn
USER MANUAL
4. TRANSMITTER BATTERY LOW
When the indicator lights constantly after triggered, it indicates this
transmitter is battery low. Please replace its battery as soon as possible.
This receiver works with AC 80V to 240V. Simply plug into a well
visible AC wall socket, it'll turn on.
* PLEASE NOTE THE TR A N S M I TTER & RECEIVER ARE
READY TO USE
Two transmitters can be assigned to the receiver by sequence.
The transmitter can only be assigned if it is not yet known in the
memory of the receiver.
2. CHANGE THE MELODY
BATTERY INS TALLATION
Test
Telephone Plug
RJ11
Battery
compartment
OPERATION
CODE CONFLICT
If the telephone signaler coding is the same as another sensor you must
change the code. After you have changed the code re-matching the
telephone signaler.
+
Open the cover Remove the battery
Plug the telephone line into the telephone socket as the diagram. The
system is ready to use.
PAR TS & FUNCTION
BATTERY LOW IND ICATOR
The status of sensor battery is indicated on the receiver. Please
refer to the " battery low indicator" on the receiver.
TELEPHONE SIGNALER
Paring to the receiver
The telephone signaler is already paired with the receive. You can add (pair)
one more transmitter to the system follow the instructions of the receiver.
+
CR2032
Open the cover
+
Press and hold the test
button, insert the battery
whilst holding the button
for 5 seconds. The LED will
flash 5 times when a new
code is generated
Safety Instructions
Warning: To prevent fire or shock hazard. Do not expose this
unit to rain or moisture.
The lighting flash with an
arrowhead within a triangle
alerts you to uninsulated
dangerous v ol tage within
the p ro duc t' s enc lo s ur e
that could cause an electric
shock
T h e e x c l a m a t i o n p o i n t
within a triangle alerts you
to pressence of important
operating, maintenance and
servicing instructions in this
user's manual.
T O R E D U C E T H E R I S K O F
E L E C T R I C S H O C K D O N O T
REMOVE COVER (OR BACK) NO
U S ER S E R VIC E A B L E PA R T S
INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
- The socket-outlet shall be installed near the
equipment and shall be easily accessible.
DT-100
1. Read these instructions.
2. Keep these instructions.
3. Read all warnings.
4. Follow all instructions
5. Do not use this device near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other.
9, Do not tamper with the polarized & Grounding plug. Each blade of the plug has a
special purpose for seamless communication & safety. A grounding type plug
has two blades and a third grounding prong.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the product. When moving the cart/product
combination to avoid injury from tip-over (When applicable).
13. Unplug this product during lightning storms or when unused for a long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
product has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the product, the
product has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. This product shall not be exposed to dripping or splashing water and that no
object filled with liquids such as vases shall be placed on the product.
Liquid damage is not covered by warranty.
16. Mains plug is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains
completely, the mains plug should be disconnected from the mains socket outlet
completely.
17. Caution marking is located at the bottom of device.
18. The marking information is located at the bottom of device.
Important Safety Instructions

DT100R Multi-Alert Receiver:
Power by: AC plug (V DE 2 round pin plug for EU)
Adaptor: Built-in AC Power 90V-240V 50/60 Hz 3W
Product dimensions: 120 (L) x 64 (W) x 31 (H) mm
Product Weight: 110 grams
Wireless frequency: radio frequency 868.0 ~868.6MHz MHz for Europe
Transmission distance 300m /1,000ft (direct line of sight)
DT100T Wireless Telephone Signaler:
Battery type: CR2032
Battery approx. weight : 2.9 grams
Product dimensions: 88.5 (L) x 34 (W) x18.5 (H) mm
Product Weight: 35 g (incl. battery)
Frequency of RF: radio frequency 868.0 ~868.6MHz for Europe
Transmission Power: 7dBm
Distance Range: 300m /1,000ft (direct line of sight)