SYBO SF-CB-2GA User manual

Operating Instructions
Please read and keep in door use only. Don’t discard
the instruction
Commercial Coffee Maker
Model No.: Wattage:
SF-CB-2GA
1610W
SF-UT1A
1450W
SF-UA1A
1450W
SF-CB-1AA
1450W
SF-CB-2GA 1650W
SF-BA1A 1450W
Input Volt: 120V~, 50-60 Hz
Capacity: ≈ 12Cups, depends on each model
1, Switch for Extra Hot Plate
2, Water Entrance
3, Brewing Indicate
4, Brew Chamber (also know as Filter Pan)
5, Decanter, Thermo or Airpot. (Separate purchase)
6, Main Hot Plate
7, Power Switch
8, Extra Hot Plate
Read the instructions before using the appliance.
Caution! Hot Surface!
Warnings :
This appliance is only suitable for commercial usage.
The coffee maker has to be placed in a horizontal position.
This Coffee Maker is a professional appliance, it is must be operated by trained
professionals.
The Coffee Maker shall only be used for indoor with room temperature around 25 °C.
The appliance is only to be installed in locations where its use and maintenance is
restricted to trained personnel.
Remain in the vicinity of the machine while machine is in operation.
1

2
Never immerse the machine in the water. If the machine has been soaked, it must be
dried and checked by specialist before using it again.
Never pour Hot Water, Coffee, or Coffee Powder into the water reservoir.
Never pour more than 2.2 liter of water into the Water Reservoir
Don’t disconnect appliance with wet hands and don’t pull the power cord.
The power cord should be replaced by qualified person with specified type, please
contact the service agent or for further advice.
When the machine is in use, some parts of the machine will become very hot. Ensure
the line of cord does not touch the hot parts. The use should also be careful not to touch
the hot parts.
Keep away from water sprayed/spraying area.
Installation:
Please check that your filter basket is assembled correctly, with the spring wedged firmly
at the bottom of the filter basket.
1.Place the Machine on a firm and horizontal surface with plenty of room above to allow
easy and safe filling of the water tank.
2.Plug machine with a 110-120V~ power.
3.Place an empty glass decanter at correct position under the filter basket.
4.Pour cold water (no more than 2 liters) into the water reservoir and wait for 2 minute for
water to force the air out of the machine.
5.Turn the switch ON and the "In Use" indicator lights up.
6.Some HOT WATER should start to flow into glass decanter.
7.4~5 minutes later, the "In Use" indicator will turn off indicating the brewing process has
ended.
8.You should repeat the above process twice to clean the internal parts of the machine
before brewing coffee for first time.
9.During above operation, it is normal to hear some brewing and pumping sounds of
water and to see some water vapor coming out of the machine.
In case, if any incorrect on operates or over flow, please TURN-OFF the switch
immediately to STOP the procedure.

3

4
Operation
Place a filter paper into the filter basket and put appropriate amount of coffee in the
filter paper (your coffee supplier should be able to provide you with information
about correct yields).
Slide the filter basket into position.
Place the empty decanter (Pot or Airpot) at the correct
position under filter basket.
Pour 1 full glass decanter of cold water into the water
reservoir.
Turn the switch ON, the "Indicator" will light up.
Brewed coffee will start to flow into the glass decanter.
When the "Indicator" light turns off, the brewing cycle has
completed.
Dispose of used coffee grounds and filter paper, rinse filter
basket in clean water – unit is now ready to make another
brew of coffee.
The Hot plate is specially designed for coffee in coffee decanter to keep warm
only. Don’t put empty coffee decanter or other thermos on it.
The coffee maker must not be cleaned by a water jet.
There are some water will always remaining in the hoses, boiler of the machine,
if the unit will not be used for some time, or machine should be to removed, you
should always pour out the remaining water and clean it for storage.
Keep away from water sprayed/spraying area.
Remain in the vicinity of the machine while machine is in operation.

5
Maintenance
Cleaning:
It is important that the Machine and its accessories be kept clean after using.
For dirt or smudges on the Machine, it is better to clean them with a soft damp cloth, and
if necessary, with a non-corrosive and/or non-abrasive detergent or cleaner.
De-sediments
On areas in the water boiler, hard water will cause chalk and limestone will to accumulate
when machine is used. To keep the machine in the best condition and ensure each coffee
brewing resulted in the best taste, we recommend that of the machine has successive
brewed for 200 time used for 6 months, a De-sediments operation be carried out as the
following:
•Add 300 ml fresh lemon juice or condensed lemon juice to 1 liter of water.
•Slide filter pan into position.
•Place an empty pot at the correct position under the filter pan.
•Pour the lemon juice solution into the water reservoir.
•Turn the switch ON.
•Some of hot water will drop into the jug, until the solution of lemon juice push out the
water remained inside of the machine and there is some solution of lemon juice start
to drop into the jug, than turn the switch OFF.
•Wait for 5~6 minutes to enable the rest of solution to run through with sediments, than
turn the switch ON again.
•When solution of lemon juice is no longer dripping out, set switch OFF and flush the
solution away.
•Since some solution of lemon juice will remain in the machine, we must run brewing
process several times with water only until there is no more taste and smell of lemon
juice in the hot water that flow out from the machine.
Due to lime may build up much fast than you imagine, we suggest usurer to
De-sediments even month for once at least.
In case, if the units stop works (no power) during the normal operate suddenly,
but when the unit cooling down the unit is re-workable again, than it is very
probably causing the limes built up. Please run the De-sediment process.
In case, if the thermostat reaction causing the lime
build up, user must to presses down and clicks the
thermostat before de-scale or next operation.