Sylvania SGQC113-MBK User manual

1
ELECTRIC FIREPLACE HEATER
Model: SGQC113-MBK
INSTRUCTION MANUAL
ATTENTION:
1. Find a location for the fireplace heater that is protected from direct sunlight.
2. Do not plug the unit into the power outlet before reading all instructions.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1) Read all instructions before using this electric fireplace heater.
2) This electric fireplace heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. The grill directly in front of the heater outlet becomes
hot during heater operation. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away from
the front of the unit and keep them away from the sides and rear.
3) Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the fireplace is left operating and unattended.
4) Always unplug heater when not in use.
5) Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner.
6) Do not use outdoors.
7) This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where it may fall into a bathtub or other
water container.
8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from traffic area and where it will not be
tripped over.
9) To disconnect heater, turn controls to off, then remove plug from outlet.
10)Do not insert or allow foreign objects to enter any ventilation or exhaust open-
ing as this may cause an electric shock or fire, or damage the heater.
11)To prevent a possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where openings may become blocked.
12)A heater has hot and arcing or sparking parts inside. Do not use it in areas
where gasoline, paint, or flammable liquids are used or stored.
13)Use this heater only as described in this manual. Any other use not recommend-
ed by the manufacturer may cause fire, electric shock, or injury to persons.
14)Avoid the use of an extension cord because the extension cord may overheat
and cause a risk of fire. However, if you have to use an extension cord, the cord
shall be No.14 AWG minimum size and rated not less than 1875 watts.
15) Do not plug this product into a receptacle controlled by a wall switch
or dimmer.
16)When storing or transporting the unit and cord, keep in a dry place, free from
excessive vibration and store so as to avoid damage.
NOTE: The stove may emit a slight harmless odor when first turned on. This is
caused by activating the internal heater components for the first time and should
not occur again.
A 15 AMP circuit is required to operate this heater. If the breaker trips when the
heater is used then you may need to move the heater to another location or unplug
other appliances that are on the same circuit. If you require an extension cord, use
one that is rated at 1875 watts.
IMPORTANT
PLEASE NOTE WHEN YOU OPEN THE CARTON CAREFULLY CHECK
THE UNIT AND MAKE SURE THERE IS NO DAMAGE. IF YOU HAVE ANY
PROBLEMS WITH THE UNIT, WITH HOW THE VARIOUS FUNCTIONS
WORK, DAMAGED OR MISSING PARTS PLEASE CALL 1-800-459-4409
(9AM TO 5 PM EST) IMMEDIATELY FOR SERVICE.
NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL
FREE NUMBER . DO NOT DISPOSE OF YOUR CARTONS UNTIL YOU ARE
COMPLETELY SATISFIED WITH YOUR NEW STOVE HEATER.
NOTE: Light bulbs may become loose during shipping. If the flame effect is dim or
does not work, please check that light bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs. Please do not return the sample to the store
before checking light bulbs.
LEG ASSEMBLY
Before using your unit please install the legs as shown in diagram below.
After completely reading instructions, confirm that all controls on stove are in the
OFF position. Plug the unit into a 15 amp, 120 volt outlet.
SYLVANIA is a registered trademark of OSRAM SYLVANIA, used under license.

2
OPERATION
Controls and switches are located on front panel inside the glass door.
FLAME: Press this button into the I position for main power and flame effect. The
indicator light will turn on. See below for other control switches.
HEATING: For low heat function - Press this switch while the FLAME switch is in
the I position for low heat. The indicator light will turn on.
TURBO: For high heat function - Press this switch while the FLAME and HEATING
switches are in the I position for high heat. The indicator light will turn on.
THERMOSTAT: To adjust the temperature to your individual requirements. Turn
the thermostat dial to the right (clockwise) to increase the desired temperature
and to the left for lower temperature. This thermostat control dial can only be
used while the FLAME switch and HEATING/TURBO switches are in the I position.
When the heater reaches the desired temperature, the heater and Heating /Turbo
indicator light will turn OFF but the fan will continue to operate. Adjust this knob
to restart the heater.
FLAME INTENSITY: Turn the dimmer dial clockwise or counter clockwise to get
the desired flame intensity. The dimmer switch can only be used when the FLAME
switch is in the Iposition.
NOTE: When the FLAME switch is turned to the OFF position, all other heater
functions will stop even though the switches may be in the Iposition.
ThERMOSTAT CONTROL
The heat output is controlled by the thermostat, according to the room tempera-
ture. Set the thermostat dial fully clockwise to the maximum position initially.
When the room is warm enough, reduce the setting by slowly turning the thermo-
stat dial anti-clockwise until the heater just clicks OFF. This will then maintain the
room temperature at the desired level.
CAUTION:
IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL
CONTROL, A PROGRAMME CONTROLLER, A TIMER OR ANY OTHER
DEVICE THAT SWITCHES ON THE HEATER AUTOMATICALLY, REMEMBER
TO OBSERVE ALL SAFETY WARNINGS AT ALL TIMES.
THE STOVE HEATER HAS A SAFETY OVERHEAT PROTECTION. IF THE
OVERHEAT PROTECTION TRIPS, TURN OFF THE FLAME SWITCH AND
UNPLUG THE POWER CORD FROM THE RECEPTACLE. IT SHOULD RESET
AUTOMATICALLY AFTER 5 MINUTES.
WARNNIG:
DISCONNECT POWER AND UNPLUG THE POWER CORD BEFORE
ATTEMPTING ANY MAINTENANCE OR CLEANING TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. THE BULBS IN YOUR
UNIT CAN BECOME EXTREMELY HOT. ALLOW AT LEAST 10 MINUTES
BETWEEN TURNING OFF THE UNIT AND REMOVING THE LIGHT BULBS
TO AVOID THE ACCIDENTAL BURNING OF THE SKIN.
FLAME EFFECT
The flame effect is created with the use of a 40 watt B-10 candelabra light bulb with
an E-12 (small) socket base. The light bulb will have to be replaced from time to
time when it burns out.
During normal operation, the stove heater will always give you simulated flame
function. If the intensity of flame suddenly increases, it means that the light bulb is
going to burn out.
Replace the light bulb immediately, according to the instructions below. Do not
operate the stove heater when the light bulb burns out or without the light bulb.
ChANGING ThE LIGhT BULB
STEP 1: Open the door of unit with the handle.
STEP 2: Loosen the 2 screws at the front of the log set inside the stove. Carefully lift
the logset up far enough to access the light bulbs. You will find 1 X 40W
Type B-10 candelabra light bulb with E-12 socket base at the bottom.
STEP 3: Replace the burned out light bulb using a new 40 watt Type B-10 candelabra
light bulb.
STEP 4: Reinstall the logset.
STEP 5: Plug in the unit.
CLEANING
To clean unit first turn off controls on unit and unplug unit from power source.
To clean glass door; remove dust with clean dry cloth or to remove finger prints and
other marks clean glass with clean damp cloth. Do not use abrasive cleaners
or spray liquids on glass door surface.
Metal and metal painted parts should be cleaned with damp cloth. Do not use
abrasive cleaners or spray liquids on these surfaces.

3
WARRANTY
Every electric stove is tested before it leaves the factory and it is guaranteed for
one year. If the unit should fail to operate correctly within one year from the date
of purchase, call customer service at 1-800-459-4409 EST . We will, at our discretion
either repair or replace the unit. It will have to be returned to us freight prepaid and
we will return the repaired or replaced unit to you freight prepaid. The company’s
sole obligation is to repair or replace the unit.This warranty is void if in the opinion
of Quality Craft the unit has been tampered with, altered, misused, damaged,
abused or used with the wrong power source. Light bulbs are not covered by this
warranty. The warranty is for homeowner use only and does not cover units used in
commercial situations.
Imported by
Quality Craft Ltd.
Laval, Quebec, Canada H7S 2G7
1-800-459-4409 (EST)
www.qualitycraft.com
Made in China