SYMA X5SC User manual

Please ensure you read and fully understand this manual before operating.
Specifications:
Item No.: X5SC
Function: up/down, forward/backward, turn left / Right,With GYRO /Flash lights
360-degree 3D special function.
Battery: 3.7V 500mAh Li-poly
Charging time: About 100 minutes - USB Charging
Flying time: More than 8 minutes
Controlling distance: Inside = 30 meters+ / Outdoors = 45 meters+
Product Size: 315 x 315 x 105mm
Frequency: 2.4Ghz
Channels: 4
Required: 4 x AA Batteries for transmitter
USER GUIDE AND MANUAL

-3-
INSTALL LANDING SKIDS & BLADE GUARDS

-2-
A
B
GET TO KNOW YOUR TRANSMITTER
Battery Cover
1.Use a screwdriver to remove the screw on the back of transmitter, then open the battery
cover (Figure 1).
2.Install 4 “AA” batteries (not included) into the back of transmitter then replace battery
cover and reinstall the screw (Figure 2).
4 X AA(LR06)
1.5V Batteries
Figure 1 Figure 2
1 - Install batteries with correct polarity.
2 - Do not mix old and new batteries.
3 - Do not mix different types of batteries.
TRANSMITTER BATTERY INSTALLATION
LCD DISPLAY

-4-
2
缺产品
1
1 - Ensure the Quadcopter is switched
OFF then remove the battery cover.
2 - Remove the battery plug from the
battery port. Then slide battery pack
out of the model
QUADCOPTER BATTERY CHARGING
3
5
4
3 - Connect the battery to the USB
charger making sure the connection
is tight.
4 - Insert the USB cable into the USB
port of the computer
The indicator on USB cable will glow
during charging, than it will go OFF
when battery fully charged.
5 - Re insert the battery pack. Reconnect
the battery plug and replace the
battery cover.
Charging time: about 75 minutes — Flying time: about 7-10 minutes
When charging, please ensure the battery is placed on a hard non flammable surface
When charging, please remove the batteries from the quadcopter.
The charging process should be supervised by an adult.
Allow the battery to cool in between charges.
Only use the supplied USB charger to charge the battery.
Do not cut or modify the battery wires.
Do not puncture or Pierce the battery pack.
The transmitter has 2 built-in modes, Mode 1 & Mode 2, in
line with different customer’s usage pattern. Keep pushing
button B to right, than turn on the transmitter power to
change Mode 1 or Mode 2.
CONTROLLER MODES

-5-
MODE 1
Operating direction
Hover up and down Forward and backward
Push the throttle up or down, the
quadcopter flies upward or downward.
Push the direction lever up or down, the
quadcopter flies forward or backward.
Sideward fly
Turn Left and Right
Pull the direction lever left or right, the
quadcopter flies to left side or right side.
Pull the throttle left or right, the
quadcopter turns to left or right.
Fine-tuning operation
Turn left/right fine-tuning
Sideward fly fine-tuningForward/Backward fine-tuning
When the quadcopter keeps
flying forward / backward, you
can correct it by pressing
fine-tuning button down / up.
When the quadcopter keeps
flying to left / right side, you
can correct it by pressing the
Fine-tuning button right / left.
When the quadcopter keeps
rotating to left /right, you can
Correct it by pressing the
fine-tuning button right / left.

READY TO FLY YOUR QUADCOPTER
Step 1: Turn ON the
transmitter
Step 3: Close the battery
cover and turn on the
quadcopter.
Step 2: Open the battery
cover & insert the battery
into the power port.
Step 4:
Push the throttle lever to the highest position,
and then pull it back to the lowest position.
There will be one clear sound from the transmitter,
this shows that the quadcopter has entered into
the pre-flight state.
TIP:
When syncing your quadcopter keep
it in a horizontal position.
Horizontal
position
-7-
SPECIAL FUNCTIONS
3D Roll
Once you are familiar with the basics and have
mastered hovering you will be able
to perform an exciting ariel stunt.
Ensure you are hovering more
than 3 meters from the ground
and in a clear area.
Once hovering press
the 3D Roll switch on the Top
Right hand side of the transmitter,
then push the right rudder
(in any direction)
to make the X5SC Roll.

-8-
RE-START FUNCTION
Press the power switch to turn on
the transmitter.
Restart function:
To return the transmitter to factory settings, please follow the steps below.
Press the power switch to turn on the quadcopter.
When the quadcopter indicator quickly flashing
to slowly flashing,please push the throttle lever to
the highest position,and then pull it back to the
lowest position. Then the quadcopter indicator
changed from slowly flashing to normal lights up.
Place the quadcopter on a horizontal position,
then push transmitter both left and right lever to
lowest right corner for about 2-3 second ,
indicator on the quadcopter changed from normal
lights up to quickly flashing ;After 2-3 second ,the
indicator changed to normal lights,it means the
quadcopter restarted /reset successfully.
HEAD FREE FUNCTION
1. Turn on power switch of remote control.
2. After aircraft connects with power supply, place the
switch in “ON” position, adjust the direction pointed
by aircraft’s handpiece and regard it as the dead
ahead in headless situation.
3. Push the accelerator’s push rod of remote control to
the highest point and pull back to the lowest point.
When remote control pops, it indicates that
frequency modulation and forward definition have
already finished.
Front
Read
Left Right

-10-
TROUBLE SHOOTING
Problem Reason Solution
No response
from the
quadcopter
Quadcopter
is slow to respond
or difficult to
manoeuver
1.Quadcopter battery is too low 1.Charge the quadcopter
1.Replace or recharge the battery.
2.Replace transmitter batteries.2.Transmitter battery power too low.
1.Insuffcient power with the transmitter.
SPARE PARTS
SYSX5SC-01
Fuselage Set
SYSX5SC-02A
Main Blades x 4
SYSX5SC-03
Landing Skid Set
SYSX5SC-04
Blade Guards
Even the very best pilot has accidents. Please see listed below a full range of replacement
parts aimed at getting you back up into the air with a minimal amount of fuss.
These parts can be ordered using the numbers below from either your original point of
purchase or through a local model shop.
SYSX5SC-05
Light Covers
SYSX5SC-06
Motor A
SYSX5SC-07
Motor B
SYSX5SC-08
Light Boards
SYSX5SC-09
Receiver Board
SYSX5SC-10
LiPo Battery
SYSX5SC-11
USB Charger
SYSX5SC-12
Camera Unit
SYSX5SC-13
Card Reader
SYSX5SC-14
Transmitter

-9-
1. Push the camera into the locating hole on the battery cover.
2. Open the battery cover with the camera attached.
3. Lock screws to ensure camera unit stays secure.
4. Close the battery cover with camera attached and insert the 3-pin plug into the socket .
Make sure the 3-pin plug of camera is inserted to the quadcopter.
Turn the quadcopter power on, the camera works normally when the RED
indicator light changes form flashing to GREEN and stays on.
If the RED indicator just lights up then goes off seconds later, it means there
is no SD Memory card in the camera. Please insert the supplied SD card in,
then the indicator light will turn GREEN.
Turn on the transmitter and pull left lever up and down to connect signal between
quadcopter and transmitter.
Take Photo: To take a PHOTO push the button near
the throttle lever UP. The camera will take a photo after
a beep from transmitter when the GREEN indicator
on camera flash one time in RED.
Take Video: To take VIDEO push the button near the
throttle lever DOWN for a few seconds. The camera
starts taking video when you will hear a beep from the
transmitter and the GREEN indicator on camera changes
to RED and keeps flashing. Press the button slightly again, another beep means
video stopped and the RED flashing indicator on camera will keep light on GREEN.
Thanks to the 6 axis gyroscope, you can throw
the quadcopter and push the throttle right up, it
will automatically level out and hover smoothly
in the sky, This can also be done when the
quadcopter is rolling.
1 2 3 4
INSTALL CAMERA Camera unit is supplied fitted with the X5C Version
PHOTOGRAPHY / VIDEO USE

-11-
01
06
07
07
10
03
03
04
04
05
02
08 09
12
13
14
15
11
08
EXPLODED VIEW