Synco G2 User manual

G2(A2)
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

3
Caring For Your SYNCO Product
•Please keep the product in a dry, clean, dust-free environment.
•Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
•Use only a soft and dry cloth for cleaning the product.
•Malfunction may be caused by dropping, impact of external force.
•Do not attempt to disassemble the product. Doing so voids warranty.
•Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
•Failure to follow all the instructions may result in mechanics damage.
•Warranty does not apply to human errors.
Package list
RX receiver x1
TX Transmitter x2
Carrying Bag x1
Mic Windshield x2
Eject Pin x1
3-in-1 Charging Cable x1
External Lav Mic (With Wind Muff) x2
3.5mm TRRS Phone Cable x1
3.5mm TRS Camera Cable x1

4
Product Instruction
TX Transmitter
1. External Mic Input
6. Pairing
2. USB-C Port
7. Built-in Mic
3. Power (MUTE)
8. Display Screen
4. Reset (Help with Eject Pin)
9. Pocket Clip
5. Low Cut
RX Receiver
1. USB-C Port
6. 3.5mm Audio Output
2. Power (Mono/Stereo)
7. 3.5mm Monitoring Jack
3. Reset (Help with Eject Pin)
8. Display Screen
4. Channel A Gain Control
9. Pocket Clip
5. Channel B Gain Control

5
Display Screen
RX Receiver
Operations
TX
1. Power/Mute
Long Press 2s: turn on/off the system
Short Press: mute/unmute the microphone
2. Charging
5V/2A; with USB-C Charging Cable
Please fully charge the product before use.
Low Cut On
Power Indicator
Recording
Muting
Channel
Audio Dynamic Display
Recording Mode:
Mono/Stereo
Channel A
Channel A Gain
Channel A Audio
Dynamic Display
Power Indicator
Channel B
Channel B Gain
Channel B Audio
Dynamic Display
TX Transmitter
Disconnected
Connecting
Connected

6
3. External Mic Input
TRS Mic Only
(Note: When using an external mic, please insert it into the mic input properly.)
4. Mic Windshield & Device Installation
5. Reset
Eject Pin
MIC
MUTE
RESE

7
6. Low Cut
Short Press: 150Hz Low Cut On
Short Press again: Low Cut Off
7. Pairing
TX-Pairing
RX-Channel A
RX-Channel B
Long press for 3s at the same time
Disconnected
Connecting
Connected
Low Cut On
Low Cut Off
RESET

8
The system will pair automatically after power on.
(Note: Before successfully connecting, the transmitter channel will display A by default.
The TX connected to the receiver first is Channel A, and the one connected later is
Channel B.)
Manual pairing: long press the Channel A Gain Control and Channel B Gain Control on
the RX and pairing on the TX for 3 seconds at the same time.
RX
1. Power/Mono/Stereo Switch
Long Press 2s: turn on/off the system
Short Press: Switch Mono/Stereo mode (Note: Stereo mode is unavailable in phone
devices.)
2. Charging
5V/2A; with USB-C Charging Cable
Please fully charge the product before use.

9
3. Reset
Eject Pin
4. Gain Control
Channel A
Channel B
0-5 Level (0→3→6→9→12→15→0)
Each press increases the gain of Channel A/Channel B by one level.
5. Pairing
TX-Pairing
RX-Channel A
RX-Channel B
Long press for 3s at the same time
RESE
RESET

10
Disconnected
Connected
The system will pair automatically after power on.
Manual pairing: long press the Channel A Gain Control and Channel B Gain Control on
the RX and Pairing on the TX for 3 seconds at the same time
(Note: The first TX that successfully connects with the RX will be Channel A.)
6. Audio Monitoring & Output Connection
3.5mm TRS Camera Cable
3.5mm TRRS Phone Cable
Apple Adapter (With MFI
Certification)
3.5mm Audio Output
3.5mm Monitoring Jack
Headphone Impedance
under 100Ω