3
Slide the main switch to : the infrared field is turned down
and will only send a signal to the pager by pushing " " on
the right. If the indicator lights up, it means the motion sensor is
working correctly.
Tip: the "BUTTON" is also a button to pair the motion sensor
to the pager.
PUSH
BUTTON
Legal Disclaimer
Instructional Videos
Q: Can I pair additional components or pager to the existing pager system?
A: Yes. The pager is capable to program with up to 3 components. Follow the
instructions on "Add/Replace Component" to start the programming. The
programming color sequence for the pager is RED, GREEN and BLUE.
Frequently Asked Questions - FAQ
SYNLETT's products rely on wireless technology which is subject to physical and environmental considerations. Please be aware that the
transmitter will not be 100% accurate if it is out of range at anytime. It is the end-user’s responsibility to make sure that the product is
used correctly and within range of each other. SYNLETT's products are designed to augment well designed care programs & practices.
We do not claim that any of its products are suitable as a substitute, or as a total solution for individuals that require care and constant
supervision & are at risk. We recommend that all personnel receive periodic training in the operation of these products and products are
tested before each use. It is important to read and follow the directions. WARNING: Failure to comply with the warning may result in
injury or death. These devices are not suitable for all individuals. Other devices may be required. These devices are not a substitute for
visual monitoring by a caregiver. The manufacturer does not claim that these devices will stop elopement and/or stop falls. These
devices are designed to augment caregivers’ comprehensive resident mobility management program. These devices are to be used by a
licensed caregiver only. Test these devices before each use. Read the instructions and Legal Disclaimer. The SYNLETT wireless call
system and its optional add-ons/accessories have a simple design that's easily installed by the end user. As such, it is the entire
responsibility of the buyer to insure that the product is properly installed and tested. Further, the product is not designed to replace
good caregiving practices including, but not limited to: A.) Direct patient supervision B.) Adequate training for staff personnel for
elopement and fall prevention C.) Testing of the system before each use. WHERE PERMISSIBLE, IT IS THE SELLER’S INTENT TO LIMIT
ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO REFUND OF THE PURCHASE PRICE OR
REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY LIABILITY FOR COMPENSATORY OR OTHER DAMAGES ARISING OUT OF THE
USE OF THE GOODS. FCC ID: 2A4LY-F007 & 2A4WH-QF018.
FCC STATEMENT: Changes or modifications not expressly approved by the party responsible for compliance could void your authority to
operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures: 1) reorient or relocate the receiving antenna, 2) increase the separation between the equipment and receiver,
3) connect the equipment into an outlet on a circuit different from that to which the receiver is connected, or 4) consult the dealer or an
experienced radio/TV technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received
Manufactued by Zhongshan Gaxin Technology Co., Ltd.
MADE IN CHINA
Ver 2023Q2
Watch more hands-on instructional videos.
Available at SYNELTT Youtube channel:
https://www.youtube.com/@mysynlett.
Or scan the QR code for a direct link to SYNLETT Youtube channel.
Q: Are the call buttons waterproof?
A: The call buttons are rated IPX4 water resistant - meaning it withstands
splashes from any direction, making them splash-proof. However, they cannot
be submerged in water.
Q: When I press the call button, the pager does not respond.
A: Check if the indicator lights up on the call button when pressing the button.
Or try replacing it with new AA batteries on the pager.
If the issue persists, follow the instructions on "Add/Replace Component" to
re-program the call button(s) to the pager.
Q: Can I adjust the detection distance of the motion sensor?
A: There is a detection adjustment knob, which is below the battery
compartment of the sensor. Insert a mini screwdriver into the slot and twist the
knob in a clockwise/anti-clockwise direction to adjust the detection distance.
Q: When I switch on the pager to DINGDONG or ALARM and press the VOLUME
button to adjust the volume, the pager does not function correctly or it makes a
strange click noise.
A: Switch the pager to OFF and to ALARM/DINGDONG a few times and check if
the issue persists.
including interference that may cause undesired operation.
Add / Replace Component
BLUEGREENRED
NOTICE: The first component that you would like to pair to the pager
MUST be a BRAND NEW unprogrammed component. Otherwise the
pager will NOT initiate the programming mode.
IMPORTANT: All existing components are required to re-program to
the pager regardless of adding or replacing component(s) to the
existing pager.
press and hold
OR
press and hold
Switch the pager to OFF then switch it to DINGDONG mode, quickly within 5
seconds, press and hold the until you hear a
DINGDONG sound.
For the call button, press and hold the call button; for the motion sensor, ensure it is
on PUSH mode, press and hold the mini BUTTON on the right as the image shows
below.
NEW unprogrammed component
1
Repeat the step, quickly
within 5 sec, press and hold
the next component button
until a BLUE indicator lights
up on the pager with a
DINGDONG sound. The 3rd
component is programmed
to the pager in BLUE
successfully.
42
A RED indicator on
pager will light up
with a DINGDONG
sound, it means the
1st component is
programmed to the
pager in RED
successfully.
3
Quickly, within 5 sec,
press and hold the next
component button until a
GREEN indicator lights up
on pager with a DINGDONG
sound. The 2nd component
is programmed to the pager
in GREEN successfully.
The pager will exit the programming mode automatically after 5 seconds with no
operations.
5
To add a new component or replace component to your exiting pager, please follow
the steps below
(if you are pairing the motion sensor(s), slide the main switch to
PUSH mode before proceeding to the steps below) :
NEW Unprogrammed
Call Button
NEW Unprogrammed
Motion Sensor
Select An Alert Mode
DINGDONG
Slide the switch on the bottom of the pager to
select either chime sound or alarm siren as alert.
- the pager only sounds one time when
receiving a signal from the call button or the motion
sensor.
- alarm siren will sound for about 20 sec
when receiving a signal from the call button or the
motion sensor.
DINGDONG
ALARM
Adjust Volume Level
Stop the Alarm Sound
When the pager is on mode, the alarm siren
will sound for 20 sec when the pager is triggered.
Press and hold the " VOLUME " button for about 2
sec to stop the alarm if needed.
ALARM
Adjust the pager volume by pressing the " "
button on the side of the pager to cycle through
volume levels from low, medium and high.
A "Di-Di" sound rings out to indicate the current
volume level.
VOLUME
Press the Component to Test
The pager will sound the selected alert tone with an indicator flashing when
receiving a signal from a component.
and each component
represents unique indicator color: . It allows the caregiver to
recognize and differentiate the call by reading the indicator color on pager.
The pager is capable to program with up to 3 components
RED, GREEN and BLUE
Set Up the Pager
Slide the belt clip into the slot on the back of the
pager if needed.
The batteries are pre-installed in the pager. Slide
open the battery cover on the back of the pager.
Remove the insulating tab from the battery and
close the battery cover.
The
Clip
Caregiver Pager - Setup
4 5 6
