Long Range Systems Butler II Specification sheet

Each button on the one or five button Butler II can be pro rammed to send a unique messa e
to separate pa ers or roup of pa ers. Both the five-button and one-button models can also
send a specific messa e for an external switch or sensor.
Installation
To put the Butler II in operation:
Note: If your Butler II is not already programmed, refer to the programming guide first.
1. Install the 3-batteries in the butler (note the end)
2. Locate the mounting bracket where it is to be used. (use screws, straps or velcro)
3. Install the batteries.
4. Position the unit into the notches in the mounting bracket and press until latch en-
gages.
5. Connect an external sensor (if used)
6. Turn on the pager (refer to the pager booklet).
7. Press the button(s) to test the pager.
Normal Op ration
1. The indicator light will be faintly blinking
2. Press a button, the indicator light will flash and the pager will receive the message.
3. For external contacts, enable the contact and the pager will receive the message.
Advanc d F atur Op ration
Enablin the followin features require the pro rammin kit. Instructions for this kit are contained
in the Help file.
Auto Off/On
The Butler II can be set to automatically turn off or on at pre-selected times of the day.
Pag Acknowl dg
The Confirmation button will send a message indicating the time between a button press
Long Range Systems 1Butler II Quick Guide
Butler II
Five and One Button Paging System
QUICK SETUP & OPERATION

(or other input) and staff response.
Low Batt ry Pag
The Butler II can send a low battery message when batteries are low.
Lockout
The alarm input can be locked out (disabled) for a period of time. This allows staff to pass
throu h monitored areas without settin off alarms.
• The staff member presses Confirmation button simultaneously,
• Then enters a 3-digit disable code.
• The alarm is disabled for a selected time and will reinitiate when the alarm con-
tacts are restored.
Long Range Systems 2Butler II Quick Guide
Latch
Tie Wraps
Screws
Velcro
Battery
+ End
Battery
Door
Mounting
Notches
External
Input
Confirmation
Button
Buttons
Indicator Light
Confirmation
Button
Paging
Buttons
Indicator Light
Confirmation
Button
Paging
Buttons
Push
For
Service
Five Button One Button

WARRANTY
Lon Ran e Systems Inc warrants this product a ainst any defects that are due to faulty material or workmanship for a two-
year period after the ori inal date of consumer purchase. The warranty does not include dama e to the product resultin from
accident, misuse, improper electrical connection, or failure to charge the product within 30 days of receipt. Recharge-
able pagers are required to stay on charge while not in use. Rechargeable pagers that are left off of charge for longer
than 30 days will have a negative impact on the life of the batteries requiring them to be replaced thus voiding the war-
ranty. If this product should become defective within the warranty period, we will repair or replace it with an equivalent prod-
uct, free of char e. LRS will return your product via UPS round shippin . All warranty claims must be initiated throu h our
customer service department:
Long Rang Syst ms, LLC, 4550 Exc l Pkwy, Suit 200, Addison, TX 75001.
No r turn or r plac m nt can b r c iv d without prior authorization and
th prop r RMA Numb r post d to th outsid of th shipping contain r.
This warranty ives you specific le al ri hts and you may also have ri hts that vary from state to state.
Copyright © Octob r 2004, Long Rang Syst ms, LLC All Rights R s rv d
This document contains proprietary information of Lon Ran e Systems, LLC (LRS) and is intended for use only by it’s employees
or customers. None of the material contained herein may be copied, reproduced, republished, downloaded, displayed, posted,
or transmitted in any form or by any means, includin but not limited to, electronic, mechanical, photocopyin , recordin , or oth-
erwise without the prior written permission of LRS. Additional copies of this manual may be obtained by contactin LRS.
Screen displays, keyboard layouts, hardware descriptions, or software are proprietary to LRS and are subject to copyri ht and
other intellectual property ri hts of LRS and shall be treated in accordance with the previous para raph.
All attempts have been made to make the information in this document complete and accurate. LRS is not responsible for any
direct or indirect dama es or loss of business resultin from inaccuracies or omissions. Specifications and other information
contained within this document are subject to chan e without notice.
Lon Ran e Systems, LLC reserves the ri ht to make chan es without further notice to any products herein. Lon Ran e Sys-
tems, LLC makes no warranty, representation or uarantee re ardin the suitability of its products for any particular purpose,
nor does Lon Ran e Systems, LLC assume any liability arisin out of the application or use of any product or circuit, and
specifically disclaims any and all liability, includin without limitation consequential or incidental dama es. “Typical” parame-
ters that may be provided in Lon Ran e Systems, LLC data sheets and/or specifications can and do vary in different applica-
tions and actual performance may vary over time. All operatin parameters, includin “Typicals”, must be validated for each
customer application by customer’s technical experts.
Lon Ran e Systems, LLC products are not desi ned, intended, or authorized for use as components in systems intended to
support or sustain life, or for any other application in which the failure of the Lon Ran e Systems, LLC product could create a
situation where personal injury or death may occur.
Should Buyer purchase or use Lon Ran e Systems, LLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Lon Ran e Systems, LLC and its officers, employees, subsidiaries,
affiliates, and distributors harmless a ainst all claims, costs, dama es, and expenses, and reasonable attorney fees arisin out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alle es that Lon Ran e Systems, LLC was ne li ent re ardin the desi n or manufacture of the part, device or system.
This equipment enerates uses and can radiate radio frequency ener y and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no uarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turnin the equipment off and on, the user is encoura ed to try to correct the interference by one or more of
the followin measures:
• Reorient or relocate the receivin antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Long Range Systems 3Butler II Quick Guide

RF Warning Stat m nt:
The device has been evaluated to meet eneral RF exposure requirement. It should be operated in a stationary wall mount or
table top confi uration and should not be held or carried while in operation. The user is cautioned to observe a minimum sep-
aration distance of at least 20 centimeters (8 inches) from the body of the user or nearby persons while transmittin from the
device.
Long Range Systems 4Butler II Quick Guide
XU-0028 043014