Synology RackStation RS1219+ Manual

Synology RackStation RS1219+
Hardware Installation Guide

Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology RackStation at a Glance 4
Safety Instructions 5
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation 6
Install Drives 6
Add a RAM Module on RackStation 8
Attach Network Interface Card to the RackStation 11
Replace System Fan 12
Mount the RackStation to a 2-Post Rack 15
Start Up the RackStation 16
Chapter 3: Install DSM on RackStation
Install DSM with Web Assistant 17
Learn More 17
Appedix A: Specications
Appedix B: LED Indicator Table
Synology_HIG_RS1219+_20180418
2

Thank you for purchasing this Synology product! Before setting up your new RackStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your RackStation.
Note: All images below are for illustrative purposes only, and may di󰀨er from the actual product.
Package Contents
Main unit x 1 AC power cord
C13-C14 power cord
Screws for 3.5” drives
x 36
Screws for 2.5” drives
x 36 Drive tray key x 2
Before You Start 1
Chapter
3
3

4Chapter 1: Before You Start
Synology RackStation at a Glance
No. Article Name Location Description
1 Power Indicator
Front
Displays power status of the RackStation. For more information, see
"Appendix B:LED Indicator Table".
2 Power Button
1. Press to power on the RackStation.
2. To power o󰀨 the RackStation, press and hold until you hear a beep
sound and the Power LED starts blinking.
3 Status Indicator Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table"
4 Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "Appendix B: LED Indicator Table".
5 Drive Status Indicator Displays the status of drives. For more information, see "Appendix B:
LED Indicator Table".
6 Drive Tray Install drives here.
7 Fan
Back
Disposes of excess heat and cools the system.
8 PCI Express
Expansion Slot Supports one PCIe x8 slot (x4 link) add-on card
9 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.1
2. Press and hold until you hear a beep sound, then press and hold
again until you hear three beep sounds to return the RackStation
to “Not Installed” status so that DiskStation Manager (DSM) can be
reinstalled.
10 USB 3.0 Port Connect external drives or other USB devices to the RackStation here.
11 LAN Port Connect network cables here.
12 eSATA Port Connect external SATA drive or Synology Expansion Unit2to the
RackStation.
13 Power Port Connect power cords here to supply power to your RackStation.
14 Console Port For manufacturing use only.
1You can keep the current admin password unchanged by ticking the "Keep current admin password unchanged" checkbox in DSM Control Panel >
Update & Restore > Reset.
2For more information about Synology Expansion Unit supported by your RackStation, please visit www.synology.com.

5Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

Tools and Parts for Drive Installation
• A screwdriver
• At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1 Pull the drive tray handle in the direction as indicated below to remove the drive tray
.
2 Load drives in the drive trays.
• For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
• For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
Hardware Setup
6
2
Chapter

7Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty drive bay.
Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.
4 Push the handle inward to secure the drive tray.
5 Insert the drive tray key into the drive tray lock, turn the key clockwise to lock the handle of the drive tray, and
then remove the key.
6 Repeat the steps above to install all prepared drives.
7 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommend all installed drives be the same size in order to optimize
drive capacity usage.

8Chapter 2: Hardware Setup
Add a RAM Module on RackStation
The optional Synology RAM module is designed for RackStation memory expansion. Follow the steps below to
install, check, or remove a RAM module on your RackStation.
To install the RAM module:
1 Shut down your RackStation and disconnect all connected cables to prevent any possible damage.
2 Remove the top cover:
a Loosen the eight screws on the top cover of the RackStation with a screwdriver. Respective screw position
is indicated above.
b Lift the top cover to the back-end of your RackStation, as indicated above.
Note: When you remove the top cover, you expose sensitive internal components. Avoid touching anything other than
the memory assembly when you remove or add memory.
Note:
1. Always install or replace the RAM module from slot 1 rst.
2. When two RAM modules are installed, the capacity of them must be identical.
3. Synology will not provide complete product warranty or technical support if non-Synology RAM modules are used
for memory upgrade.

9Chapter 2: Hardware Setup
3 Insert the new memory module in the slot:
a Align the notch on the gold edge of the module with the notch in the memory slot.
b Tilt the card and push the memory into the slot. Make sure the module is pushed in all the way.
c Use two ngers to apply rm, even pressure and push the memory module downward. You should hear a
click when the memory is inserted correctly.
Important: Hold the memory module by its edges, and do not touch the golden connectors.
4 Return the top cover into the RackStation:
a Put the top cover back into position.
b Fasten the eight screws you removed in step 2.
To make sure RackStation recognizes the new memory capacity:
1 Install DiskStation Manager (DSM). (See the next chapter for more information.)
2 Log in to DSM as admin or a user belonging to the administrators group.
3 Check Total Physical Memory in Control Panel > Info Center.
If your RackStation does not recognize the memory or does not start up successfully, conrm that the memory is
installed correctly.

10 Chapter 2: Hardware Setup
To remove the RAM Module:
1 Follow step 1 and 2 of the “Add a RAM Module on RackStation” section to shut down your RackStation,
disconnect the cables, and then remove the top cover.
2 Disengage the memory retaining clips by pushing them outwards, and the module will pop out of the slot.
3 Follow step 4 of the “Return the top cover into the RackStation” section to put back the top cover.