Synology RackStation RS3614xs User manual

Synology_QIG_RS3614xs&RS3614RPxs_20140617
Synology RackStation RS3614xs/RS3614RPxs
Quick Installation Guide

2
Table of Contents
Chapter 1: Before You Start
Package Contents............................................................................................................................................... 3
Synology RackStation at a Glance...................................................................................................................... 4
Safety Instructions............................................................................................................................................... 6
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation .................................................................................................................. 7
Install Drives........................................................................................................................................................ 7
Add a RAM Module on RackStation.................................................................................................................... 9
Add a Network Interface Card to RackStation................................................................................................... 13
Replace Malfunctioning Fan.............................................................................................................................. 14
Start up the RackStation ................................................................................................................................... 16
Chapter 3: Install DSM on RackStation
Install DSM with Web Assistant......................................................................................................................... 18
Learn More........................................................................................................................................................ 19
Appendix A: Specifications
Appendix B: LED Indicator Table

3
Chapter
1
Chapter 1: Before You Start
Thank you for purchasing this Synology product! Before setting up your new RackStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety
instructions carefully to avoid harming yourself or damaging your RackStation.
Package Contents
Main unit x 1 AC power cord x 11
Screws for 3.5" hard drives x 52
Screws for 2.5" hard drives x 52
---------
1AC power cord: RS3614xs x 1; RS3614RPxs x 2

4 Chapter 1: Before You Start
Synology RackStation at a Glance
No. Article Name Location Description
1) Power Button
Front Panel
1.Press to power on the RackStation.
2.To power off the RackStation, press and hold until you hear a beep
sound and the Power LED starts blinking.
2) Status Indicator Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table".
3) Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "Appendix B: LED Indicator Table".
4) Beep off Button Press to deactivate beep sound when malfunctions occur.
5) Disk Indicator Displays the status of installed drives. For more information, see
"Appendix B: LED Indicator Table".
6) Drive Tray Install drives (hard disk drives or solid state drives) here.
7) Power Supply On/Off
Switch
Back Panel
Press to turn on/off the power supply.
8) Power Port Connect power cords here to supply power to your RackStation.
9) Fan Disposes of excessive heat and cools the system. If a fan malfunctions,
the RackStation will emit a beeping sound.
10) Console Port For manufacturing use only

5 Chapter 1: Before You Start
No.
Article Name
Location
Description
11) USB 2.0 Port
Back Panel
Connect external hard drives, USB printers, or other USB devices to the
Synology RackStation here.
12) USB 3.0 Port
13) LAN Port Connect network cables here.
14) RESET Button
1.Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and passwords for users belonging to the
administrators group.
2.Press and hold until you hear a beep sound, then press and hold again
until you hear three beep sounds to return the RackStation to “Not
Installed” status so that DiskStation Manager can be reinstalled.
15) Expansion Port Connect Synology Expansion Units1
16)
to your Synology RackStation.
Power Supply
Safety Latch Secures the power supply in place.
17) Power Supply
Beep Off Button Press to deactivate beep sound when malfunctions occur.
18) Redundant Power LED Displays the status of redundant powers supplies, alerting the user of
power supply or fan failure
---------
1For more information about Synology Expansion Unit supported by your RackStation, visit www.synology.com.

6 Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and from chemicals. Make sure the
environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct
supply voltage. Make sure that the supplied AC
voltage is correct and stable.
To remove all
electrical current from the device, ensure that all power cords are disconnected
from the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries
appropriately.

7
Chapter
2
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation
A screwdriver
At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all data. If you still need
the data, please back it up before installation.
Install Drives
1 Find the small button located on the drive tray handle. Press the button down and pull the drive tray handle out
as illustrated below.
2 Load drives in the drive trays:
For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.

8 Chapter 2: Hardware Setup
For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
3 Insert the loaded drive tray into the empty hard drive bay.
Important: Make sure the drive tray is completely inserted. Otherwise, the drive might not function properly.
4 Push the handle inward to secure the drive tray.
5 Repeat the steps above to install all prepared drives.
6 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommended all installed drives be the same size in order to
optimize drive capacity usage.

9 Chapter 2: Hardware Setup
Add a RAM Module on RackStation
Synology offers RAM modules which allow you to expand the memory capacity of your RackStation. To install,
check, or remove your RAM module, please follow the steps below.
Install a RAM Module
1 Shut down the RackStation and disconnect all connected cables to prevent any possible damage.
Important: Before installing the RAM module, please wait for at least 30 seconds after detaching the power
cord(s) from the RackStation to ensure complete discharge. Also, please remove any static electricity before
installation by touching water pipes, a metal conduit, or another person to get rid of excess charge and avoid
damaging the motherboard, peripherals, and other components.
2 Slide the latches shown below to release the fan cover
3 Lift and remove the fan cover.

10 Chapter 2: Hardware Setup
4 To remove the screws securing the top cover, follow the steps below:
a Remove the two screws illustrated below.
b Remove the two screws located on the back. Then slide the top cover in the direction indicated below and
lift.
c Remove the screws of the securing bracket and remove the securing bracket to reveal the RAM slots.
Important: Removing the cover will expose sensitive internal components to possible harm. Please avoid touching
any other components when adding or removing memory.