SYNOQ SR1 User manual

CONTENTS
SAFETY PRECAUTION.................................................................................................3
ENVIRONMENT PROTECTION.....................................................................................4
FRONT PANEL...............................................................................................................5
REAR PANEL................................................................................................................. 5
CONNECTING YOUR SYSTEM.....................................................................................6
REMOTE CONTROLLER...............................................................................................7
1. BASIC OPERATIONS.........................................................................................9
1.1 TURN ON STB........................................................................................................9
1.2 POWER..................................................................................................................9
1.3 CHANNEL UP/CHANNEL DOWN................................................................................9
1.4 VOLUME UP/VOLUME DOWN-..................................................................................9
1.5 NUMBER................................................................................................................. 9
1.6 MUTE..................................................................................................................... 9
1.7 PAUSE...................................................................................................................9
1.8 RECALL..................................................................................................................9
1.9 FAVOR TE...............................................................................................................9
1.10 AUD O...................................................................................................................9
1.11 NFORMAT ON.....................................................................................................10
1.12 EPG..................................................................................................................10
1.13 TV/RAD O.........................................................................................................10
1.14 CHANNEL L ST..............................................................................................10
1.15 PAGE UP/PAGE DOWN.......................................................................................11
1.16 TELETEXT........................................................................................................... 11
1.17 SUBT TLE......................................................................................................11
1.18 F ND..................................................................................................................11
1.19 ZOOM...........................................................................................................13
1.20 MENU.................................................................................................................13
1.21EX T.....................................................................................................................13
1.22 OK..................................................................................................................... 14
2. MAIN MENU.......................................................................................................15
2.1.1 CHANNLE...........................................................................................................15
2.1.2 INSTALLATION....................................................................................................16
2.1.3 SYSTEM SETUP..................................................................................................19
2.1.4 TOOL................................................................................................................. 22
1

3. UPGRADE.........................................................................................................22
4. STORAGE MANAGE.........................................................................................23
5. EPG....................................................................................................................23
6. CAS....................................................................................................................23
7. NETWOR SETTING........................................................................................24
8. ADV TIMER........................................................................................................ 24
9. RADIO................................................................................................................25
10. PHOTO............................................................................................................... 25
11. MUSIC................................................................................................................25
12. MOVIE................................................................................................................26
13. WEATHER.........................................................................................................27
14. YOUTUBE..........................................................................................................27
15. GAME................................................................................................................. 28
16. TOOL................................................................................................................. 28
17. SPECIFICATIONS.............................................................................................29
2

SAFETY PRECAUTION
CAUTION:
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to "dangerous
voltage" and to prevent from a
risk of electric shock.
Warning:
To reduce the risk of electric
shock, don't open the cabinet.
Refer servicing to qualified
personnel only.
The exclamation point within an
equilateral triangle is intended to
alert the user to important
operating and maintenance
(servicing).
WARNING: Do not use this STB where contact with / or immersion in water is a possibility. Do not use
near flower vase, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the danger of fire.
WARNING: The unit should be connected to a power supply only of the type described in the operating
instructions or as marked on the unit. f you are not sure of the type of power supply (for example, 120
or 230 V) to your home, consult your local dealer or local power company.
WARNING: This product installs diodes. Do not open the cabinet or touch any parts in the inner
mechanism. Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this User manual carefully and retain
for further reference.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote control
with a soft cloth lightly moistened with a mild detergent solution.
Attachments: Never add any attachments and/or equipment without the manufacturer consent; as
such additions may result in the risk of fire, electric shock, or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from overheating.
Do not block these openings or allow them to be blocked by placing the STB on a bed, sofa, or other
similar surface, nor should it be placed over a radiator or heat register.
3

Power-Cord Protection: Place the power-supply cord out of the way, where it will not be walked on.
Please take special attentions to cords at plugs, convenience receptacles, and the point where they
exit from the unit.
Object and Liquid Entry: Never put objects of any kind into this STB through openings, as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
any liquid on the STB.
Note: Moisture may be formed on the lens n the following conditions:
when the unit is suddenly moved from a cold environment or an air-condition room to a warm
place.
immediately after a heater has been turned on.
in a steamy or very humid room.
f the moisture forms inside the unit, it may not operate properly. To correct this problem, turn on the
power and wait about two hours for the moisture to evaporate.
Parts Replacement: When the unit parts need to be replaced, user should make sure the service
technician use the replacement parts specified by the manufacturer or having the same characteristics
as the original part. Unauthorized replacement may put the unit n the risk of fire, electric shock or other
hazards.
Safety Check: After all the maintenances and repairs are done, user is required to request the service
technician to conduct the overall safety check to ensure the machine is n the proper condition.
Environment protection
Attention!
Your product is marked with this symbol. t means that the used electrical and electronic products should
not be mixed with general household waste. There is a separate collection system for these products.
DECLARATION OF CONFORMITY
The manufacturer herewith declares the conformity of that product with the following
directives and standards:
4

Front Panel
1. DC Input: 12V/1.5A input Range
2. Wifi antenna：built-in wifi model
3. RS 232 SERIAL PORT: To transfer the data to another STB or PC by RS-232 cable
4. IR Port：Connect the R cable
Rear Panel
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and checked.
Your configuration may vary depending on model.
1. RF IN (LNB IN 13/18V 500mA MAX) : Connect the coaxial cable from LNB of your Dish.
2. HDMI: Audio and Video output socket for TV set with HDM nput Jack only.
3. Ethernet Port : Plug-in Ethernet Board (RJ45 port)
4. USB Connector: USB 2.0 Host, connect to USB hard disk or flash disk
5. CA slot: CA interface support
6. AV:CVBS output
5

Connecting Your System
There are four ways to connect the receiver to your existing TV system. We recommend using one of
the following cases for the best result:
1. f you have a high definition television set, you should use a HDM cable for best result. Plug one
end of the cable into the HDM socket on the receiver and the other end into the matching socket
on your television. n this case, you do not have to make audio connections because the HDM
connector can output stereo audio or Dolby digital audio.
2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a
RCA jack on your TV.
Finally connect the coaxial cable from the LNB to the nput on the receiver.
TV with Motorized System (DiSEqC 1.2 / USALS)
Connect one end of your coaxial cable to the LNB N connector on the receiver and the other end to the
Receiver connector on the DiSEqC 1.2 / USALS motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 / USALS motor.
All our receivers are designed to be DiSEqC 1.0 / DiSEqC 1.2 /USALS compatible.
This allows multiple antennas to be connected to the receiver at the same time.
f you have two or more fixed antennas or LNBs, we recommend you use a DiSEqC 1.0 switch. Connect
the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch. Do the
same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
Connect the other end to nput on the receiver.
6

Remote Controller
7

1．POWER: To switch ON/OFF the receiver power supply.
2．TV/STB：To switch between TV and STB.
3．MUTE: To mute or restore the sound
4．TV/RADIO: To switch between TV and RAD O.
5．NUMBER EYPAD: To select TV/Radio channel and enter to programming parameters by the
numeric keys and to input the character by the alphabetical keys.
6．RECALL: To return to the previously viewed channel.
7．RED, GREEN, YELLOW, BULE EYS: Multi-function keys in menu mode.
8．MENU: Display the main menu or return to the previous one.
9．EXIT: To exit from the menu or pop-up window or cancel the present running functions.
10．PAGE +/-: To move up the cursor to the next or previous page in the menu or channel list.
11．SUB: To show subtitle.
12．TXT: To open teletext page on the channel which has teletext information.
13．FIND: Enter into a menu to search the channel you want.
14．ZOOM: To magnify a certain area on the images
15．O : To carry out the selection and enter into choused menu.
16．CH Up/Dn: To turn the next or previous channel and to move the highlight bar for selecting options
to upward or downward on the menu.
17．VOL +/-: To adjusts the sound volume up or down and to move the highlight bar for selecting
options to right or left on the menu.
18．FAV: The shortcut key to favorite menu.
19．INFO: The shortcut key to the information menu.
20．EPG: The shortcut key to the EPG menu.
21．AUDIO : Selects the audio mode among Left / Right / Stereo / Mono
22．USB: The shortcut key to the USB menu.
23．FB/FF: To play back or forward faster.
24．PLAY/PAUSE: to pause and play the file when you press play / pause key.
25．STOP: To stop the current play.
26．STEP: Jump forward by chapter.
27．NEXT: To change into the next play.
28．PREV: To change into the previous play.
8

1. Basic Operations
1.1 Turn on STB
First, press the Power to turn on the unit.
When the STB is first used, there will play the first channel from the default Channel List. f the STB is
not first used, STB will play the same channel as last time before turning off.
1.2 Power
1. Press [Power] Key can enter the Standby state
2. n Standby state, press [Power] Key again can call back the unit and go on play the previous
channel
3. User can also disconnect the device’s main power to end the Standby state.
1.3 Channel Up/Channel Down
n full screen, press [CH Up/Dn] to change channel.
1.4 Volume Up/Volume Down-
n full screen, press [Vol +/-] to adjust volume.
1.5 Number
n full screen, use number key and press [OK] on the Remote Control Unit to change channel.
1.6 Mute
1. Press [MUTE] key to mute the sound and the screen will show up mute OSD.
2. Press [MUTE] key again to restore sound.
1.7 Pause
By pressing [Pause] key once, the picture and sound will be paused and then, by pressing [PAUSE]
key again, you can continue to watch.
1.8 Recall
Press [RECALL] key will directly switch to the previous channel that you played before current
channel.
1.9 Favorite
1. n full screen, press [FAV] key, it will display a window of “Favorite Group” on the left of the
screen.
2. n the window of “Favorite”, you can move highlight by press [Ch Up/Dn] key and press [OK] key
to select favorite group.
3. You also can press [VOL +/-] keys to select different “Favorite Group”.
4. Press [Exit] key to exit the current window.
1.10 Audio
1n full screen, press [AUD O] key to open the “Audio”
window on the screen.
2You can modify the audio track by pressing
[Ch Up/Dn] key and modify the audio mode
by pressing [VOL +/-] key among Left / Right
/ Stereo / Mono.
9

1.11 Information
n full screen, press [ NFO] key can open information
screen, in the window shows the parameters of current
channel.
1.12 EPG
1The STB has an Electronic Program Guide (EPG)
to help you navigate channels through all the
possible viewing options. The EPG supplies
information such as channel listings and starting
and ending times for all available channels.
2Press [EPG] key to display EPG screen.
3Press [OK] key in each item can see more detail
information and press [Exit] key to cancel
4Press [Vol +/-] to select “back/current time/last
program or last day/next day”. Press [Ch Up/Dn]
key to channel change.
5Press [Green] key in EPG menu can open timer
menu. Yo can save a timer as you want.
6n EPG menu, press [Exit] to close EPG
screen.
1.13 TV/RADIO
n TV mode, pressing [TV/RAD O] key can switch to Radio mode. n Radio mode, press [TV/RAD O]
key to switch to TV mode.
1.14 Channel List
1n full screen, press [OK] key or [CH.L ST] can
enter “Channel List”.
2Press [Vol +/-] key to change satellite.
3Press [Ch Up/Dn] key to move highlight and
press [OK] key to play the highlighted channel.
4Press [Page +/-] key to page up and page
down.
5Press [Exit] key to exit the channel list.
10