SynQe gSmart8900 Operator's manual

Quick View Guide

1
Appearance Introduction

2

3

4
Serial No.
Component
Element
Illustration
1
LED indicator
light
The green light flickers when opening
the telephone module.
The red light flickers when low battery.
The red light/green light is on when
being charged/full charge.
The red light flickers if missing calls.
2
Power Key
Long Press: turn on or off the device.
Short Press: set the device to
deactivation or activate the
deactivated device.
3
Fingerboard
It is used for inputting the numbers or
letters, and achieving switchover of
marker or focal through navigation key
(the FN button can switch over letters
and numbers, the S button is the scan
button).
4
Left and Right
Scan Button
When enabling the scanning
application, focus the scanning lens at
the scanned objective and press this
button for scanning.
5
Volume Button
It can adjust volume when calling.
It can also adjust volume when playing
music.
6
RF cable
It is used for testing RF index of the
mobile phone.
7
RS232 Port
Standard RS232 port.
8
PTT/camera
Long press to initiate camera.
After initiating the camera function, it
can perform photograph function by
pressing this button.
9
Infrared
Windows
To aim this window to the infrared
window of other device when adopting
infrared connection.

5
10
Battery Cover
It fixes the battery with a RFID
antenna stuck inside.
11
Stylus
It is used for clicking the
corresponding area of the screen in
order to fulfill the corresponding
functions.
12
Screw of hand
belt support
It fixes the hand belt support.
13
Hand belt
support
It fixed the hand belt support.
14
Camera Head
Camera.
15
Flashlight
It provides supplementary lighting
when taking photos.
16
Hand Belt
It is easy for taking along the device.
17
Scanning Lens
One-dimensional and two-dimensional
scanning engine.
18
IC Card Cover
IC card groove and rubber plug of
USB port (14 pin port).
19
Screw of Battery
Locker Support
It fixes the battery locker support.
20
Locker of Battery
Cover
It fulfills switch on/off the locker of the
battery cover by sliding the locker to
the left or to the right.
Installation of TF Card, SIM Card, PSAM Card and Battery
Notice: Before installing/taking out the available TF card, SIM
card, PSAM card and the battery, please ensure the power supply of
the device is turned off. SIM card, provided by the operators, can
store some basic data such as names and phone numbers of the
contacts. Please be noted that some SIM card may not match the
device and please consult the local operators for replacement.
1. Ensure the device is power-off. Push the locker of the battery

6
cover of the device to the left in order to separate the back cover
and the device.
2. Take out the battery by pulling the battery belt.
3. Installation of TF card: push the locker of SIM card to the left and
uplift the locker of SIM card from the right side, then push the
locker of TF card to the upside and uplift the locker of TF card
from the downside, next put TF card in the locker (be noted that
the metal sheet of TF card shall face the metal contactor at the

7
terminal), finally put down the locker of TF card and push the
locker to the downside.
4. Installation of SIM card: push the locker of SIM card to the left
and uplift the locker of SIM card from the right side, then put SIM
card in the locker (be noted that the metal sheet of SIM card
shall face the metal contactor at the terminal), finally put down
the locker of SIM card and push the locker to the downside.
5. Installation of PSAM card: push the locker of PSAM card to the
right and uplift the locker of SIM card from the left side, then put
PSAM card in the locker (be noted that the metal sheet of PSAM
card shall face the metal contactor at the terminal), finally put
down the locker of PSAM card and push the locker to the left
side.
6. Installation of the battery: the metal contactor of the battery shall

8
be faced to the metal contactor at the terminal; ensure the
contactor of the battery is aligning at the connecting terminal of
the battery. Then, push the battery to the locked position.
7. Installation of the back cover: close the back cover and push the
locker of the back cover of the battery to the right side and finally
lock the back cover.
Plug-in and pullout of USB Cable
As it is shown in the picture, plug in the USB Cable to the pin port.
As it is shown in the picture, press downward to inclined 45°and pull out
the USB Cable.

9
Battery Charging
The new accessory battery is entitled with only part electric quantity,
so the battery must be charged before using. Normally, the battery
will reach the optimal performance after full charging and discharging
for two or three times.
There are two ways of charging the battery:
●Charging via the adapter.
●Charging via battery bay.
1. Install the battery into the device correctly.
2. Plug one end of the adaptor into the USB port of the device
according to the picture and plug the other end to the outlet of the
standard alternating power supply.
3．After finishing charging, LED indicator light will turn to the green
light and the plot of the battery will show filled.
Remark:
●Please use the accessary adaptor and USB date link for
charging the device.
Basic Functions
Power-on, Power-off and Screen lock
Turn on the device
Put the adequately charged battery into the device and long press the