syscomtec SCT-HDBTL72H KIT User manual

SCT-HDBTL72H KIT
18G HDMI Extender over CAT5e/6/7
All Rights Reserved
Version: SCT-HDBTL72H KIT_2021V1.0.0

2021V1.0
Preface
Read this user manual carefully before using the product. Pictures shown in this manual are
for reference only. Different models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till May, 2021.
In the constant effort to improve the product, we reserve the right to make functions or
parameters changes without notice or obligation. Please refer to the dealers for the latest
details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. It has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which case
the user at their own expense will be required to take whatever measures may be necessary
to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void the
user’s authority to operate the equipment.

2021V1.0
The SCT-HDBTL72H KIT is a point-to-point HDMI extender set for HDMI V2.0 and IR signals;
this kit supports 4K/UHD video @ 60Hz with 4:4:4 Chroma sampling, as well as HDMI data
rates up to 18Gbps and HDCP 2.2 compliant. The SCT-HDBTL72H KIT provides HDMI
transmission up to 230 feet (70 meters) for 4K@60Hz 4:4: 4, or 262 feet (80 meters) for 1080p
over single CAT5e/6/7 cable. It supports bi-directional IR, RS232 and 12V PoC, and automatic
video resolution down-scaling.
Features
Supports HDMI V2.0, up to 4K@60Hz 4:4:4, HDR 10, 18G, HDCP 2.2.
Extends 4K HDMI signal up to 230 feet (70 meters), or 1080p HDMI signal up to 262 feet
(80 meters) over a single CAT5e/6/7 cable.
Supports video resolution down-scaling, the 4K input can be automatically degraded to
1080p output on receiver for compatibility with legacy 1080p display device.
HDMI loop out on transmitter.
Bi-directional IR and RS232 pass-through.
Supports bi-directional 12V PoC, only one power supply required.
Features visually lossless compression with no latency.
Smart EDID management.
Compact design, easy to install and simple to operate.
Packing List
1x Transmitter (Tx)
1x Receiver (Rx)
1x IR Receiver
1x IR Emitter
2x 3-pin Terminal Blocks
1x Power Adaptor (12V DC 1A)
1x Quick Operation Guide

2021V1.0
Transmitter Panel Description
Tx Rx
SIG
MERGE
BYPASS
COPY TX
EDID
12345678
1. CAT OUT: Connects to the CAT IN port of receiver by CATx cable. It supports 12V PoC and
the transmitter can be powered from the receiver. The green LED illuminates when power
is applied. The orange LED illuminates when there is a valid HDMI signal input.
2. IR IN: Connects to IR receiver for IR pass-through.
3. IR OUT: Connects to IR emitter for IR pass-through.
4. RS232: Connects to RS232 control device (e.g. PC) or a third-party device to be controlled
for RS232 pass-through.
5. DISPLAY: Connects to local HDMI display device.
6. SOURCE: Connects to HDMI source device.
7. EDID: 3-pin DIP switch for EDID setting.
MERGE: If there are two display devices in this system, the unit will output the video
with the lower resolution in this mode to ensure video can be shown on both displays.
BYPASS: The source device learns the EDID from the remote display connected to the
Receiver’s HDMI output.
COPY Tx: The source device learns the EDID from the local display connected to the
Transmitter’s HDMI loop output.
8. DC 12V: DC connector for the power adapter connection.
Receiver Panel Description
Tx Rx
SIG
IN
123456
1. CAT IN: Connects to the CAT OUT port of transmitter by CATx cable. It supports 12V PoC
and the receiver can be powered from the transmitter. The green LED illuminates when
power is applied. The orange LED illuminates when there is a valid HDMI signal input.

2021V1.0
2. IR IN: Connects to IR receiver for IR pass-through.
3. IR OUT: Connects to IR emitter for IR pass-through.
4. RS232: Connects to RS232 control device (e.g. PC) or a third-party device to be controlled
for RS232 pass-through.
5. DISPLAY: Connects to HDMI display device.
6. DC 12V: DC connector for the power adapter connection.
Connection Diagram
Note:
 The IR and RS232 commands cannot be triggered simultaneously.
 The CATx cable length should not be less than 15 meters for best video output.

2021V1.0
Specifications
Transmitter
Input
(1) SOURCE
Input Connector
(1) 19-pin type-A female HDMI
Output
(1) DISPLAY, (1) CAT OUT
Output Connector
(1) 19-pin type-A female HDMI, (1) RJ45
Control
(1) IR IN, (1) IR OUT, (1) RS232
Control Connector
(2) 3.5mm mini jacks, (1) 3-pin terminal block
Receiver
Input
(1) CAT IN
Input Connector
(1) RJ45
Output
(1) DISPLAY
Output Connector
(1) 19-pin type-A female HDMI
Control
(1) IR IN, (1) IR OUT, (1) RS232
Control Connector
(2) 3.5mm mini jacks, (1) 3-pin terminal block
General
Video Resolution
Up to 4K@60Hz 4:4:4, HDR 10
Color Space
RGB, Rec. 601, and rec. 709 BT2020
HDMI Audio Format
LPCM 7.1 audio, Dolby® TrueHD, Dolby Digital® Plus, DTS:X™,
and DTS-HD® Master Audio™ pass-through.
Transmission Distance
4K: 15 to 70 meters (49 to 230ft)
1080p: 15 to 80 meters (49 to 262ft)
HDMI Version
2.0
HDCP Version
Up to 2.2 (The HDCP content of TX HDMI output follows the
remote RX display device’s.)
EDID
EDID Setting by 3-pin DIP Switch
Power Supply
Input: 100 to 240V AC, 50/60Hz;
Output: 12V DC 1A
Power Consumption
5.6W (Max)
Operation Temperature
-5 to +55℃ (+23° to +131°F)
Storage Temperature
-25 to +70℃ (-13° to +158°F)
Relative Humidity
10% to 90%, Non-condensing
Dimensions (W*H*D)
100mm x 16mm x 80mm (without mounting ears)
127mm x 16mm x 80mm (with mounting ears)
Net Weight
Tx/Rx: 185g
Note: The extender set does not support HBR audio.

2021V1.0
Kontakt:
syscomtec Distribution AG
Raiffeisenallee 8
DE 82041 Oberhaching
Telefon: [phone]
Telefax: [phone]
E-Mail: [email protected]
Homepage: www.syscomtec.com