Syska SmartMeeting User manual

Get your smart AI meeting
assistant
Start your free trial now!
1Go to https://smartmeeting.sembly.ai
2Sign up
3 Enter the serial number of your device (you can nd it on
the packaging or the device itself)
4Use the code “SM2022D1” to activate your Team Plus plan (unlimited
number of meetings in the rst month, then up to 4 meetings per month)
User
manual
12
11
10
9
7
4
5
2
1
8
4
3
6
1. V- Volume down
2. Bluetooth
3. Power
4. Microphones
5. V+ Volume up
6. Mute
7. Status LED
8. Speaker
9. Reset
10. Power socket
11. Battery status LED
12. USB Type-C port
© 2022 Speech Processing Solutions GmbH. All rights reserved.
This product has been manufactured by and is sold under the responsibility of Speech Processing
Solutions GmbH, and Speech Processing Solutions GmbH is the warrantor in relation to this product.
Specications are subject to change without notice. Philips and the Philips shield emblem are
registered trademarks of Koninklijke Philips N.V. and are used under license.
Document version 1.0, 03/02/22 For more support visit
www.dictation.philips.com/pse0540help
User manual
Portable Conference
Microphone
with Sembly Meeting
Assistant
PSE0540
SmartMeeting
pse0540.indd 4pse0540.indd 4 02/03/2022 14:17:4202/03/2022 14:17:42

To reset the device, press and
hold the reset button on the
back side of your device by
using a small, pointed object, for
example, a paper clip
Press to mute yourselfPress V+ or V- to change
the volume of the speaker
Hold for 1 second,
to disconnect from
the current device
1 sec
5
4
Go to the bluetooth
settings of your device
and choose "PSE0540"
in the list
3
starts blinking white and
the speaker says "pairing"
2
1 sec
1
6
stops blinking and
lights up. The speaker
says "connected"
To fully unpair, go to the
bluetooth settings of your
device and remove "PSE0540"
Press to turn
the device on
Connect the device to a computer.
Note: The device can only be
charged via the AC adapter
You can now use the device
with various meeting software,
by selecting "PSE0540"
1 sec
123
Press to turn
the device on
1
Connect the correct plug
to the AC adapter
23
Connect the AC adapter
to the device and a power
socket
The LEDs on the back indicate
the battery status and stop
blinking after the device is
fully charged
pse0540.indd 8pse0540.indd 8 02/03/2022 14:17:4302/03/2022 14:17:43

f
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
pse0501_fcc-ce_warning-card.indd 1pse0501_fcc-ce_warning-card.indd 1 03/03/2022 13:54:5303/03/2022 13:54:53

Manufactured for: Speech Processing Solutions GmbH,
Gutheil-Schoder-Gasse 8–12,
1100 Wien, Österreich
www.philips.com/dictation
Brand: Philips
Product name: Portable Conference Microphone
Model: PSE0540
Operating temperature: 5° – 45° C / 41° – 113° F
Maximum Bluetooth
transmit power:
+6 dBm
The product shall only be connected to a USB interface of version USB2.0
or higher. Charging via USB is not supported, the device can only be
charged via the included AC adapter.
For this device, Head SAR and Body SAR was performed with the device
congured in the positions according to EN62209-1:2016 & EN62209-
2:2010, and Body SAR was performed with the device 0mm from the
phantom. Body SAR was also performed with the headset attached and
without.
pse0501_fcc-ce_warning-card.indd 2pse0501_fcc-ce_warning-card.indd 2 03/03/2022 13:54:5303/03/2022 13:54:53