SyxthSense SSIES-5P Manual

FEATURES
1. IEEE802.3/ 802.3u/ 802.3x
2. Support auto negotiation speed, F/H duplex mode, and auto send
data control
3. Plug-and-play , auto MDI/MDI-X connection
4. Store and Forward 100M, Switching Process Type
5. Broadcast storm protection
6. Network work state LED indicator
7. 12～48VDC power input Operating temperature ranges from -40
to 75°C
8. Dustproof, rugged industrial design, IP30 protection
PANEL LAYOUT
SSIES-5P series industry Ethernet switches provide 5 TP ports.
10/100BaseT(X) ETHERNET PORTS
IES205 series have 5 10/100BaseT(X) Ethernet ports(RJ45). The pin
out of RJ45 port display as below, connect by UTP or STP. The
maximum distance is 100m. 100Mbps is used 100Ωof UTP5 , 10Mbps
is used 100Ωof UTP 3,4,5.
RJ 45 port support automatic MDI/MDI-X operation. can connect the
PC, Server, Converter and HUB .Pin 1,2,3,6 Corresponding connection
in MDI. 1→3,2→6,3→1,6→2 are used as cross wiring in the MDI-X port
of Converter and HUB. . 10Base-T/100Base-TX are used in MDI/MDI-X,
the definition of Pins are in below table.
NO. MDI
signal
MDI-X
signal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
6 RX- TX-
4,5,7,
8 ——
Note: “TX±”transmit data±, “RX±”receive data±, “—”not use
DIMENSIONS（mm）
POWER SUPPLY CONNECTION
Topview Frontview
SSIES-5P series Ethernet Switch has 3-terminal block for power
input(V-,FG,V+), V-, V+ for 12VDC~36VDC power input, FG for
connecting device earth.
INSTALLATION
Before installation, confirm that the work environment meets the
installation requirements, including the power supply and space and
environmental conditions. Avoid in the sunshine, keep away from the
extensive heat or the area where in intense EMI.
DIN-RAIL INSTALLATION
SSIES-5P series can be installed to 35mm DIN-Rail, as follows:
1. Check the DIN-Rail Clip is fitted firmly and 35mm DIN-rail is fitted
firmly.
2. Insert the top of the DIN-Rail into the slot just below the stiff metal
spring. The DIN-Rail clip will insert into place as shown below.
WIRING REQUIREMENTS
Be sure to disconnect the power cable before installing and/or wiring
your Ethernet Switch. Calculate the maximum possible current in each
power wire and common wire. Observe local electrical regulations
Power Input (bottom)
Top Panel
Front Panel
18

dictating the maximum current allowable for each wire size. If the
current goes above the maximum rating, the wiring could overheat
causing serious damage to your equipment.
Use separate path (conduit) to route wiring for the power and Ethernet
cables to avoid interference. If power wiring and Ethernet cable paths
cross, make sure the wires are perpendicular at the intersection point.
LED INDICATOR
LED indictor light on the front panel of IES205 Series .the function of
each LED is described in the table as below.
System indication LED
LED State Description
POWER
ON Power is being supplied to
power input POWER1 input
OFF Power is not being supplied to
power input POWER1 input
OFF Abnormality
RJ45 Port have two LED indictor light, yellow light is a port rate indictor
light, green light is a port link indictor light.
10/100M
（yellow）
On 100M work mode
(100Base-TX）
Off 10M work mode 10Base-T）
Link/ACT
（green ）
On TP port is active
Blinking Data is being transmitted
Off TP port is inactive
SPECIFICATIONS
Interface
RJ45 Ports: 10/100BaseT(X) auto connection, Full /Half duplex or force
work mode, and support MDI/MDI-X connection
Technology
Standard：IEEE802.3, IEEE802.3x, IEEE802.3u
Forwarding and Filtrate Rate: 148810pps
Transmit type: Store and Forward switching process type
Support 1K MAC Address
Power
Input Voltage: 12VDC~38VDC, Overload Current Protection
Or 24VAC +/- 10%
Connection: 3 Connector Terminal Block
Mechanical
Dimensions (L×W×H): 103mm×78mm×32mm
Packaging: IP 30 Protection, Metal case
Installation: DIN-Rail, Wall Mounting
Environmental
Operating Temperature: -40 to 75°C
Storage Temperature: -45 to 85 °C
Ambient Relative Humidity: 10% to 95% (non-condensing)
Approvals
EMI：FCC Part 15, CISPR (EN55022) class A
EMS: EN61000-4-2(ESD),
EN61000-4-3(RS),
EN61000-4-4(EFT),
EN61000-4-5 (Surge),
EN61000-4-6 (CS),
EN61000-4-8,
EN61000-4-11
Shock: IEC 60068-2-27
Free Fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Warranty: 5 years
Certifications:
SyxthSense Ltd, United Kingdom
Tel : [phone] Fax : [phone]
www.syxthsense.com [e-mail]
SSIES-5P
5-PORT INDUSTRIALETHERNET SWITCH
HARDWARE INSTALLATION GUIDE
INTRODUCTION
The SSIES-5P series of industrial Ethernet switches are entry-level
industrial 5-port Ethernet switches that provide an economical solution
for your industrial Ethernet connection, support
IEEE802.3/802.3u/802.3x. Dustproof and full close structure and the
IP30 case with LED indicators make the plug-and-play SSIES-5P
switches easy to use and reliable. These switches have been designed
for harsh industrial environments. SSIES-5P series support 5
ports10/100Base-T(X), Full/Half duplex mode, and auto MDI/MDI-X
connection.
PACKING LIST
The SSIES-5P switch is shipped with following items.
1. Ethernet switch SSIES-5P (plus terminal block) ×1
2. Hardware Installation Guide ×1
3. DIN-Rail Mounting Clip (wall mounting optional) x 1