Tach-It SH-450 User manual

LABEL REWINDER
MODE L: SH-450 (E
.:;-::.. ' ~
.; --=-- "- •
• I. '
.' . I .:~ ~
USER MANUAL
OPERATION, MAINTENANCE AND TROULBESHOOTING

LAB EL REWTNDER
Contents
A. External view---------------------------------------------------------------------------------3
B. Specifications--------------------------------------------------------------------------------4
C. Operation-------------------------------------------------------------------------------------5
[).
~otice------------------------------------------------------------------------------------------Ei
E. Parts picture----------------------------------------------------------------------------------7
F. Pa rts picture----------------------------------------------------------------------------------8
2

LAB EL REWIND ER
A. External View
ACRYL GUIDE INSIDE
','
-" ACRYL GUIDE OUTSIDE
CONTROL BOX
"
/;
.
r' .
/ ~.'
SPEED VOLUME ' /" .'
HANGER GUIDE
______ of
J • .
_________ ROLL HANGER
(.:, .... '- ~
I -, .
.' ,
POWER SIW I
BASE PLATE
3

LABEL REWfNDER
B. Specifications
Power supply----------------------------------------------This machine setted 11 OvaIts.
Machine width----------------------------------------------------------------14.6
II 137 . oe m
Machine length--------------------------------------------------------------
-11 .S II 130. Oem
Machine height---------------------------------------------------------------14.6
137. Oe m II
Net weight --------------------------------- ------------------------------------------ Sk gs
F=use---------------------------------------------------------------------------------------------61\
Label Size Width:
Ma
x: 45inch
Label Roll Max:
<D 120inch
Speed:
Variable
Speed control motor
Max 240
R. P.M
4

LA BEL RE WIND ER
c. Operation
----JI". REWINDING
-----+. UNWINDING
Procedure of label setting
REWINDING
1. Push Hanger guide inside into Roll hanger.
2. Push Acryl guide inside into Roll hanger.
3. Thread leading end of label on Guide shaft1 and under Guide shaft2.
4. Continue to thread label as shown
in picture.
Grip leading end into the groove
in Roll hanger.
6. Push Acryl guide outside and Hanger guide into Roll hanger.
7. The setting of Speed adj. should be initially set at O.
8. Turn Power switch "on".
9. Adjust Speed adj. until the desired speed.
UNWINDING
1.2. Same as above.
3. Push the label roll into roll hanger.
4. Thread leading end of label under guide roller and on guide shaft.
ADJUST
1. Choose unwinding or rewinding.
2. Choose clockwise or anticlockwise direction by the face label attached
011 label roll.
5

LABEL REWTNDER
D. Notice
iJ])isconnect from power supply when carrying out any maintenance.
CLEAN
1. Do Not-Spray of splash fluids over machine.
2. Do Not-Remove or adjust the factory preset peel plate.
3. Do-Keep all surfaces clean.
LABEL
4. It should not have cut line in backing paper.
5. Label roll should be less then CD120inch.
Maximum of label width is 45inch.
6. When label is exchanged by other size, the positon volume should be start
from "0".0
10. Use proper voltage which
is marked in the label of machine.
11. The fuse should be 6A.
6

LABEL REWTNDER
E. PARTS PICTURE
. -
~ R-5
..'_ -- _______ · ~~f ·;
. '. . -- R-3
'l ..t
.· L~ l .; -----r
J.. .
"1 -
L-1. Control box
L-2.
Ac code input & Power s/w
L-3. Speed volume
L-4. Rewinder/Unwinder select lever
L-5. Direction lever
L-6. Grip
R-1. Acryl guide inside
R-2. Hanger shaft
R-3. U-pin
R-4. Acryl guide outside
R-5. Hanger spring guide
R-6. Core adapter
B-1. Base plate
B-2. Hanging bar
8-3. Rubber pad
7

LABEL RE WTND ER
F. PARTS PICTURE
C-2
. ~ /
C- 1 ------"-~
"
C-3',
C-1. PCB bo a rd
C-2. Mic ro-s witch
C-3. Motor
8