Tacx T2028 User manual

EN |NL |DE |FR |IT |ES |PT |DK
NO |SE |FI |PL |CZ |GR |CN |JP
Quick Start
ANT+ Antenna

Connect the T2028 USB ANT+ Antenna into a free USB port of your desktop.
NL Sluit de T2028 Tacx USB ANT+ Antenne aan op een vrije USB poort van je
computer als de Tacx Trainer software hierom vraagt.
DE Schließen Sie die T2028 USB ANT+ Antenne an einen freien USB-
Steckplatz an Ihrem Computer an, wenn Sie bei der Installation der Tacx
Trainer-Software dazu aufgefordert werden.
FR Branchez l’antenne T2028 USB ANT+ dans un port USB libre de votre
ordinateur lorsque vous y êtes invité à l’installation du logiciel Tacx Trainer.
IT Collegare l’antenna USB ANT+ T2028 a una porta USB libera del computer
quando viene indicato dalla procedura di installazione del software Tacx Trainer.
ES Conecte la antena T2028 USB ANT + a un puerto USB libre de su
ordenador cuando así lo indique la Instalación del software del Tacx Trainer.
PT Ligue a Antena USB ANT+ T2028 numa porta USB livre do seu portátil/PC
quando lhe for solicitado na instalação pelo software Tacx Trainer.
DK Tilslut T2028 USB ANT+ Antenne til en ledig USB port i din computer, når
Tacx Trainer Software installationen angiver det.
NO Koble antennen T2028 USB ANT+ inn i en ledig USB-port på din bærbare

datamaskin når dette indikeres av Tacx Trainer-programvareinstallasjonen.
SE Anslut T2028 USB ANT+-antennen i en ledig USB-port på din dator när
Tacx Trainer-mjukvaruinstallationen säger så.
FI Yhdistä T2028 USB ANT+ Antenni laitteen tietokone vapaaseen USB-
porttiin Tacx Trainer Software –asennusohjelman ohjeistamana.
PL Podłącz antenę USB ANT+ T2028 do wolnego portu USB komputera, gdy
wyświetli się komunikat z odpowiednią informacją podczas instalacji
programu treningowego firmy Tacx.
CZ Připojte T2028 USB ANT a anténu k volnému USB portu počítačový dle
instrukcí při instalaci softwaru Tacx Trainer.
GR Συνδέστε την Κεραία USB ANT+ T2028 σε μια ελεύθερη θύρα USB του
φορητού ή επιτραπέζιου υπολογιστή σας όταν σας ζητηθεί από το πρόγραμμα
εγκατάστασης του Λογισμικού Tacx Trainer.
CH 当 Tacx Trainer 软件在安装中出现提示时，将 T2028 USB ANT+天线插入您笔
记本/PC 上空闲的 USB 端口
JP Tacxトレーナーのソフトウェアインストールで指示されたら、T2028 USB ANT+ステ
ィックアンテナをお使いのノートパソコン/PCの空いているUSBポ ートに 接 続します
T2028

User guidelines & Warranty conditions
Safety precautions
This device is not designed for industrial or commercial applications.
Do not expose the product to water or moisture.
Maintenancew
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty
No guarantee or liability can be accepted for any changes and modifications
of the product or damage caused due to incorrect use of this product.
General
Designs and specifications are subject to change without notice.
All logos brands and product names are trademarks or registered trade-
marks of their respective holders and are hereby recognized as such.
This manual was produced with care. However, no rights can be derived.
Tacx cannot accept liability for any errors in this manual or their conse-
quences.
Keep this manual and packaging for future reference.

Specifications
Wireless protocol ANT+, Supports up to 8 channels simultaneously
Frequency 2,4Ghz
RF Output Power 0dBm (typical)
USB Interface 2.0
Power supply USB 5V
Cable Length 1,5m

FCC and IC Declarations
Compliance statement (part 15.19)
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning (part 15.21)
Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
This in particular is applicable for the antenna which has been delivered with the
RF Exposure (OET Bulletin 65)
To comply with FCC RF exposure requirements for mobile transmitting devices, this
transmitter should only be used or installed at locations where there is at least 20cm
separation distance between the antenna and all persons.
Information to the User (Part 15.105 (b))
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweenthecomputerandantenna.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp
CE Declaration of Conformity
For the following equipment:
Product name: Tacx T2028 ANT+ USB Antenna
Is herewith confirmed to comply with the requirements set out in the
Council (European parliament) Directive on the Approximation of the Laws
of the Member States relating to Electromagnetic Compatibility of Radio and
Telecom device (1999/5/EC). For the evaluation regarding this Directive, the
following standards were applied: EN 55022 |EN 61000-4-2 |EN 61000-4-3 |
EN 61000-4-4 | EN 61000-4-6

T2028.25C|2018-01