Taichuan TC-U9DA-D User manual

Digital Unit Door Panel
Before using this device, please read this manual and properly
stored it for future reference
Instructions
1
1
2
4
4
4
1. The basic structure of the door phone unit
1). The instruction for appearance and function module of door phone unit
2). The basic interface type of door phone unit
3). The description for basic interface of door phone unit
2. Introduction of the door phone unit
1). The keyboard of door phone unit instructions
2). Introduction of the basic functions
3. The instruction of common functions for the door phone unit
1). Intercom calling
2). Indoor machine monitoring
3). The unlock
4). The IC cards function
4. The configuration instructions of door phone unit
1). Automatic configuration of system startup
2). Configuration of IC card information
3). Configuration of the door phone unit IP address
Content
1
The power interface
The network interface
The unlock interface
1). The instruction for appearance and function module
of door phone unit
1.The basic structure of the door phone unit
Microphone
Camera Luminous
Compensation
Swiping
Card Area
Call Button Speaker
2).The basic interface type of door phone unit
The wiring diagram
Note: RJ45 network port connect with
8 wire CAT-5 cable to the router
3
3
3
3
3
3
5
5
5
5
2
Model：TC-U9D A-D
U9DA-D Wiring Diagram

3). The description of basic interface for the door phone unit
Network cable length: it is better not longer than 80m
Wire sequence of network interface:
The power interface:12V DC
The unlock interface: The internal relay contact
(normal open)
RJ45 port
Brown
1 2 3 4 5 6 7 8
White
Orange Orange White
Green Blue White
Blue Green White Brown
2.Introduction of the door phone unit
1).The keyboard of door phone unit instructions
There is a button on the keyboard of door phone unit ,
and it is used to call and hung up
2). Introduction of the basic functions :
Intercom calling
System monitoring
The unlock
Remote configuration and update
Voice prompt function
IC card entrance guard system
1).Intercom calling
Call methods: Presses the call button to call the resident，
and there is a call voice prompt.
Call response: It will ringing after the call succeeded,
otherwise it will prompt failure:
Answer: After connect to the indoor machine, voice will
prompt answering , then the system will stop ringing .
Calling hang up: press the call button to hang up, voice
prompt with hang up.
Image transmission: After the call succeeded, the door
phone unit will transfer images to the resident.
Automatic hang up: If there is no answer in 30s from the
indoor machine, the call will automatically hang up, and
during the intercom talking, it will automatically hang up
with 3 minutes.
3. The instruction of common functions
for the door phone unit.
3
2).Indoor machine monitoring
The indoor machine monitor the outdoor phone unit and
outdoor phone unit transfer video to the indoor machine.
Indoor machine answering the door phone unit, it can
transmit the audio data.
When indoor machine monitor the outdoor phone unit, it
can operate the unlock.
Outdoor machine can response the hang up command
from the indoor monitors.
Automatically hang up: intercom talking will automatically
hang up for 3 minutes.
3).The unlock
Unlock under monitoring: when the door phone unit is in a
sta te of monito red i nterc om, w hen t he mon itoring
equipment proceed the unlock operation, the door phone
unit will have corresponding unlock actions.
Call and unlock: When the door phone unit called the
indoor machine, and received the unlock command, it will
respond to unlock actions.
IC cards unlock: When swiping the authorised IC card, the
door phone unit will have corresponding unlock actions,
and user will hear a voice and a buzzer prompt.
4).The IC cards function
Support card types: IC card
Swiping card and unlock: with prompt voice when the
outdoor phone read the IC card.
Swipe card and disarming: After swiping the authorised
card on the door phone unit , the indoor machine will be
informed to disarming.
Status of swiping card indicates: the door phone unit will
rec o g n i z e t h e I C c a r d s th r o ug h t h e re g is t r a ti o n
information, the legitimacy of other card, giving relevant
prompt.
Unregistered card: Prompt the voice of unregistered card,
and sent the record to the management center.
Swiping card successfully: only the registered IC card can
swiping card and unlock successfully.
4
4. The configuration instructions of
door phone unit
1).Automatic configuration of system startup
when system startup, allocate according to the factory
default IP address, it’s IP address can be automatic
configured by the management center.
2).Configuration of IC card information
The specific operation of IC card configuration by the
management center:
Add card: read and edit the IC card number, and
configure for the resident.
Download card: after edit and add the IC card, batch
download the data to the door phone unit.
Modify the card: according to the requirement, modify
the IC card number for the resident and re-download it
again to the door phone unit.
Remove card: according to the requirement, edit and
delete the IC card number, and re-download it again to
the door phone unit.
3).Configuration of the door phone unit IP address
The network card physical address:
The MAC address for each door phone unit is unique on the
global network.
The IP address configuration way:
a. setting the IP database of the intercom by the
management center, and choose the resident which have
given the IP address for the door phone unit, the
management center can searching the online device,
setting it to the given IP, and the IP address of the door
phone unit will be automatically changed.
b. setting the IP address by the indoor machine, and
connect the door phone unit to the same network of the
indoor machine, enter the door phone configure menu, the
indoor machine can searching the online device, setting it
with the given IP, and the door phone unit can be
automatically configured.
5