Taiden TMX Series User manual

TMX Series Professional Matrix Switchers
Professional Matrix Switchers
TMX-MV2SDI Multi-format Video & Audio Processor
Installation and Operation Manual
V 1.0

I
Remark:
All rights reserved for translation, reprint or reproduction.
Contents may change without prior announcement.
All technical specifications are guideline data and not guaranteed features.
Taiden Co., Ltd. is not responsible for any damage caused by improper use of this manual.
The equipment must be connected to earth!
This product conforms to the rules of the European directive 2004/108/EC.
If any detailed information needed, please contact your local agent or TAIDEN service center in your region.
Any feedback, advice and suggestion about the products is appreciated.
TAIDEN is the registered trademark of TAIDEN Co., Ltd.

Important Safety Instruction
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
6. The MAINS plug serving as a disconnection device,
should be easy to operate.
7. The apparatus should be connected to the MAINS
socket-outlet with protective earth.
8. Clean only with dry cloth.
9. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
10. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
11. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade and the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
12. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
II
13. Only use attachments/accessories specified by the
manufacturer.
14. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
15. Unplug this apparatus during lightning storms or
when unused for long periods of time.
16. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
17. Do not place the equipment on any uneven or
unstable stand; original product package or
appropriate package should be used to avoid damage
caused by strong impacts during transportation.
18. Power supply cords:
AC 90 V~250 V 50 Hz/60 Hz
19. For service, please contact the nearest TAIDEN
Service Center.
20. All TAIDEN products are guaranteed for 3 years
excluding the following cases:
A. All damage or malfunction caused by human
negligence;
B. Damage or malfunction caused by improper
operating by operator;
C. Parts damage or loss caused by disassembling
the product by non-authorized personnel.
21. Use ONLY specified connection cable to connect the
system equipment.
22. Upon receipt of the product, please fill out the
Warranty Card enclosed and post it to TAIDEN
Service Center nearby in your region.
CAUTION: To reduce the risk of electric shock,
DO NOT open covers, no user serviceable parts
inside. Refer servicing to qualified service
personnel only.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION: DO NOT use alcohol, ammonia or
petroleum solvents or abrasive cleaners to
clean the devices.
The lightning flash with an arrowhead symbol, with
an equilateral triangle, is intended to alert the user
to the presence of uninsulated ‘dangerous voltage’
within the products enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.

Important Safety Instruction
The exclamation mark within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
III
Attention: Installation should be performed by
qualified service personnel only in accordance
with the National Electrical or applicable local
codes.
Power Disconnect: Units with or without ON – OFF
switch have power supplied to the unit whenever
the power cord is inserted into the power source;
however, the unit is operational only when the ON
– OFF switch is in the ON position. The power cord
is the main power disconnect for all units
WARNING: To reduce the risk of fire or
electric shock, DO NOT expose units to rain
or moisture.
WARNING: The apparatus should be
connected to a mains socket outlet with a
protective earthing connection.

IV
Contents
Installation & User Guide........................................................................................................... V
Chapter 1. Functions and indications....................................................................................... 1
Chapter 2. Installation and connection..................................................................................... 2
2.1 Installation.........................................................................................................................................................2
2.2 Connection between Processors and PC.........................................................................................................2
2.3 Connection with input, output devices ..............................................................................................................2
Chapter 3. Setup and Operatio ................................................................................................3
3.1 Input type ..........................................................................................................................................................3
3.2 Output type .......................................................................................................................................................4
3.3 Out resolution....................................................................................................................................................4
3.4 Line in sens.......................................................................................................................................................4
3.5 Line out vol........................................................................................................................................................5
3.6 Net setup...........................................................................................................................................................5
3.7 RTC setup.........................................................................................................................................................6
3.8 Picture setup .....................................................................................................................................................6
3.9 Factory Default..................................................................................................................................................7
3.10 COM baudrate ................................................................................................................................................7
3.11 VGA input Pos ................................................................................................................................................7
3.12 About...............................................................................................................................................................7
Chapter 4. Technical data ........................................................................................................8
Appendix：Commendatory assignation ...................................................................................10

Installation & User Guide
About this manual This manual is applicable to:
This manual is a comprehensive guide to the
installation and operation of TAIDEN TMX-MV2SDI
Multi-format Video & Audio Processor. It includes:
operation and setup, installation and connection,
technical data, etc.
The manual is divided into the following chapters:
Chapter 1: Function and indication
Descriptions in detail of the functions and indications of
the TMX-MV2SDI Multi-format Video & Audio
Processor.
Chapter 2: Installation and connection
Descriptions in detail of the installation and connection
of the TMX-MV2SDI Multi-format Video & Audio
Processor.
Chapter 3: Setup and operation
Descriptions in detail of the configuration and operation
of the TMX-MV2SDI Multi-format Video & Audio
Processor.
Chapter 4: Technical data
Mechanical and electrical details of the TMX-MV2SDI
Multi-format Video & Audio Processor.
TMX-MV2SDI Multi-format Video & Audio Processor
V

Chapter 1. Functions and indications
Figure 1.1 Panel of TMX-MV2SDI
Front panel:
1. “MENU” button
a) If in current state, press “MENU” to go to the
main menu;
b) If in menu state, press “MENU” to go to the
sub menu;
c) Select/Deselect in network configuration.
2. “Õ” (Left) button
3. “Ö” (Right) button
4. “EXIT” button
5. “SENSOR” indicator (reserved)
6. “NETWORK” indicator
Indicator flashes when receiving data from
central control system.
7. “ACTIVE” indicator
Indicator will be turned on when video input
signal is active.
8. “POWER” indicator
Rear panel:
9. RJ45 interface
10. RS-232 communication interface
11. VGA input
12. YPbPr input
13. HDMI input
14. DVI-D input
15. 3G-SDI input
16. VGA output
17. HDMI output
18. 3G-SDI output
19. Power cable interface
20. Grounding point
21. CVBS input
22. Audio output
23. Audio input
1

Chapter 2. Installation and connection
2.1 Installation
Put the 1U Multi-format Video & Audio Processor into
the cabinet and fix it by screws. As figure 1.2.
2
Figure 1.2 Installation
2.2 Connection between Processors and
PC
Multi-format Video & Audio Processor can be
controlled by Central Control System via TCP/IP or
RS-232 interface and be software upgraded via
RS-232 interface.
2.3 Connection with input, output
devices
The number of input and output ports is differing,
according to the type chosen. Every audio or video
device with an AV port can be connected to the
Multi-format Video & Audio Processor. Output ports can
be connected to recorder, video or audio monitor, PA and
so on, as shown in figure 1.3.
Control Interface:
Control
RS-232 9 pin female D connector
COM Baud rate: adjustable, data: 8 bits,
stop: 1 bit, no parity check bit
Interface 2=TX, 3=RX, 5=GND
Ethernet RJ-45
Ethernet protocol TCP/IP
Ethernet speed 10M/100M
Figure 1.3 Connection example for input and output devices to Multi-format Video & Audio Processor

3
Chapter 3. Setup and Operatio
TMX-MV2SDI main interface:
Press “MENU” to go to the main menu, including:
1. Input type
2. Output type
3. Out resolution
4. Line in sens.
5. Line out vol.
6. Net setup
7. RTC setup
8. Picture setup
9. Factory Default
10. COM baudrate
11. VGA input Pos
12. About
Menu 1 to menu 12 is explained explicitly:
3.1 Input type
Select the type of input signal, including: YPbPr, CVBS,
VGA, HDMI, DVI, SDI.
Different types of input support different resolutions:
SDI input:
HD 720p: 25, 30, 50, 60;
HD 1080i: 50, 60;
HD 1080p: 24, 25, 30, 50, 60
YPbPr input:
SD: 525i (720x480i60 of NTSC),
625i (720x576i50 of PAL);
HD 720p: 50, 60;
HD 1080i: 50, 60;
HD 1080p: 25, 30
CVBS input:
SD: 525i, 625i
VGA input: 640x480p60, 800x600p60, 800x600p75,
1024x768p60, 1024x768p75,
1280x720p60, 1280x1024p60,
1280x1024p75, 1440x900p60,
DVI input: 640x480p60, 800x600p60, 800x600p75,
1024x768p60, 1024x768p75, 1280x720p60,
1280x1024p60, 1280x1024p75，
1440x900p60, 1920x1080p60
HDMI input: 640x480p60, 720x480p60, 720x576p50,
1280x720p60, 1280x720p50,
1920x1080i60, 1920x1080i59,
1920x1080i50, 1920x1080p60,
1920x1080p59, 1920x1080p50,
1920x1080p30, 1920x1080p25,
1920x1080p24
1. Press “MENU” to enter and press “Õ/Ö”
until “Input type” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
1. Input type
YPbP
r
1. Input type
▋
YPbP
r
1. Input type
▋
CVBS
1. Input type
CVBS
In:YPbPr Out:VGA
Res:800×600p60
Note：
)When the type of the video input signal has
been selected, the relevant type of audio input
signal will been set up automatically.
In:HDMI Out:VGA
Res:800×600p60
TM
X
-MV2SDI
Initializing…

3.2 Output type
Select the type of output signal, including: VGA, SDI,
HDMI.
3.3 Out resolution
Select the resolution of output. Different type of output
has different selections of resolution:
When output type is VGA, the out resolution includes:
800x600p60, 800x600p75, 1024x768p60,
1024x768p75, 1280x1024p60, 1280x1024p75,
1360x768p60, 1600x1200p60, 1400x1050p60；
When output type is HDMI, the out resolution includes:
1280x720p60, 1280x720p50, 1280x720p30,
1280x720p25, 1920x1080i60, 1920x1080i50,
1920x1080p60, 1920x1080p50, 1920x1080p30,
1920x1080p25, AUTO (select the best resolution
automatically according to EDID);
When output type is SDI, the out resolution includes:
1280x720p25, 1280x720p30, 1280x720p50,
1280x720p60, 1920x1080i50, 1920x1080i60,
1920x1080p25, 1920x1080p30, 1920x1080p50,
1920x1080p60.
3.4 Line in sens.
Adjust the line in sensitivity of analog-audio. Range:
-12dB to 6dB, step: 3dB. If the input type is SDI or
HDMI and that without video input, the line in sensitivity
can not be adjusted.
1. Press “MENU” to enter and press “Õ/Ö”
until “Line in sens.” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
4. Line in sens.
-12dB
4. Line in sens.
▋
-12dB
4. Line in sens.
▋
-6dB
4. Line in sens.
-6dB
In:YPbPr Out:VGA
Res:800×600p60
1. Press “MENU” to enter and press “Õ/Ö”
until “Out resolution” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
3. Out resolution
800×600p60
3. Out resolution
▋800×600p60
3. Out resolution
▋1024×768p75
3. Out resolution
1024×768p75
In:YPbPr Out:VGA
Res:800×600p60
1. Press “MENU” to enter and press “Õ/Ö”
until “Output type” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
2. Output type
VGA
2. Output type
▋
VGA
2. Output type
▋
SDI
2. Output type
SDI
In:YPbPr Out:VGA
Res:800×600p60
Note：
)If “SDI” is selected, the HDMI output will
export the same resolution and the VGA
output will be turned off.
)If “HDMI” is selected, the SDI output will
export the same resolution and the VGA
output will be turned off.
)If “VGA” is selected, the SDI output and the
HDMI output will be turned off.
Note：
)1920x1080p60, 1920x1080p50 and AUTO are
nonsupport when the input type is CVBS.
4

3.5 Line out vol.
Adjust the volume of audio output. Range: Mute, -30dB
to 0dB, step: 1dB. If the input type is SDI or HDMI and
that without video input, the line out volume can not be
adjusted.
3.6 Net setup
An IP address, Subnet mask and Gateway must be
assigned to the matrix if connected to a TCP/IP
Ethernet interface.
Example: IP address setup.
1. Press “MENU” and press “Õ/Ö” until “Net
setup” prompts;
2. Press “MENU” and press “Õ/Ö” until “a. IP
address” prompts;
3. Press “MENU” to enter setup;
4. Press “Õ/Ö” to select field, press “MENU”
to enter setup and press “Õ/Ö” to adjust
parameter;
5. Press “MENU” to confirm, and adjust
others in file, press “EXIT” to return to the
upper level menu.
6. Net setup
6. Net setup
a. IP address
a. IP address
192.168.1 .22
a. IP address
192.168.173.22
In:YPbPr Out:VGA
Res:800×600p60
1. Press “MENU” to enter and press “Õ/Ö”
until “Line out vol.” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
5. Line out vol.
0dB
5. Line out vol.
▋
0dB
5. Line out vol.
▋
-3dB
5. Line out vol.
-3dB
In:YPbPr Out:VGA
Res:800×600p60
6. Net setup
a. IP address
For setup of “Subnet mask” and “Gate way” proceed
such as described in “IP address”.
5

3.7 RTC setup
For setup of “Time setup” proceed such as described in
“Date setup”.
Set up the Real Time Clock parameter, include: RTC
enable, Date style, Time style, Date setup and Time
setup.
Example 1: RTC enable. 3.8 Picture setup
Set up the picture parameters of video. Include:
Brightness, Contrast, Saturation and Hue. The range of
them is 0 to 255 and the default is 128.
For setup of “Date style” and “Time style” proceed such
as described in “RTC enable”.
The date style include: Y-M-D, D-M-Y and M-D-Y. The
time style include: 24-hour and 12-hour.
Example 2: Date setup.
For setup of “Contrast”, “Saturation” and “Hue” proceed
such as described in “Brightness”.
1. Press “MENU” to enter and press “Õ/Ö”
until “Picture setup” prompts;
2. Press “MENU” to enter and press “Õ/Ö”
until “a. Brightness” prompts;
3. Press “MENU” to enter;
4. Press “Õ/Ö” to adjust parameters;
5. Press “MENU” to confirm and press “EXIT”
to return to the upper level menu;
8. Picture setup
8. Picture setup
a. Bri
g
htness
8. Picture setup
▋
128
8. Factory default
a. Bri
g
htness
In:YPbPr Out:VGA
Res:800×600p60
8. Picture setup
▋
168
1. Press “MENU” and press “Õ/Ö” until “RTC
setup” prompts;
2. Press “MENU” and press “Õ/Ö” until “d.
Date setup” prompts;
3. Press “MENU” to enter setup;
4. Press “Õ/Ö” to adjust parameter; press
“MENU” to confirm, and adjust others in
file;
5. Press “EXIT” to return to the upper level
menu.
7. RTC setup
7. RTC setup
d. Date setu
p
d. Date setup
2013-Jan-1
d. Date setup
2013-Jan-8
In:YPbPr Out:VGA
Res:800×600p60
7. RTC setup
d. Date setu
p
1. Press “MENU” and press “Õ/Ö” until “RTC
setup” prompts;
2. Press “MENU” and press “Õ/Ö” until “a.
RTC enable” prompts;
3. Press “MENU” to enter setup;
4. Press “Õ/Ö” to adjust parameter; press
“MENU” to confirm.
7. RTC setup
7. RTC setup
a. RTC enable
a. RTC enable
▋
Yes
7. RTC setup
a. RTC enable
In:YPbPr Out:VGA
Res:800×600p60
6

3.9 Factory Default
Enable/disable to reset the TMX-MV2SDI to the factory
default setting. Factory default parameter as follows:
input signal is HDMI; SDI/ HDMI output resolution is
1280 ×720p60; line in sensitivity is 0dB; line out
volume is 0dB; RTC is close.
3.10 COM baudrate
3.11 VGA input Pos
Set up the picture position of VGA input. Include: “Left
or Right” and “Up or Down”. The range of any direction
is 0 to 128, step is one pixel.
Set up the COM baudrate. Include 9600、19200、
38400、57600、115200.
For setup of “Up or Down” proceed such as described
in “Left or Right”.
3.12 About
Display the type and the firmware version of the
switcher.
1. Press “MENU” to enter and press “Õ/Ö”
until “VGA input Pos” prompts;
2. Press “MENU” to enter and press “Õ/Ö”
until “a. Left or Right” prompts;
3. Press “MENU” to enter;
4. Press “Õ/Ö” to adjust parameters;
5. Press “MENU” to confirm.
11. VGA input Pos
11. VGA input Pos
a. Left or Ri
g
ht
a. Left or Right
0
11. VGA input Pos
a. Left or Ri
g
ht
a. Left or Right
L: 6
1. Press “MENU” to enter and press “Õ/Ö”
until “COM baudrate” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
10. COM baudrate
10. COM baudrate
▋
115200
10. COM baudrate
▋
9600
10. COM baudrate
In:YPbPr Out:VGA
Res:800×600p60
1. Press “MENU” and press “Õ/Ö” until
“About” prompts;
2. Press “MENU” enter and press “Õ/Ö” to
see the information.
12. About
Ver:1.00.00.04
Ser:746500000144
In:YPbPr Out:VGA
Res:800×600p60
1. Press “MENU” to enter and press “Õ/Ö”
until “Factory Default” prompts;
2. Press “MENU” to enter setup;
3. Press “Õ/Ö” to select parameter;
4. Press “MENU” to confirm.
9. Factory Default
9. Factory Default
▋
Yes
9. Factory Default
▋
No
9. Factory Default
In:YPbPr Out:VGA
Res:800×600p60
In:VGA Out:HDMI
Res:AUTO
Note：
)This menu can only adjust when the input type
is VGA.
7

8
Chapter 4. Technical data
Type
S
p
ec. TMX-MV2SDI
Video
Gain 0 dB
Bandwidth
CVBS, YPbPr: 6 MHz
VGA: 250 MHz
DVI: 165 MHz
HDMI: 165 MHz
SDI：270 Mbps, 1.485 Gbps, 2.97 Gbps
Bandwidth flatness 0.2 dB, 100 MHz
Differential phase error 0.04°, @RL=150 Ω
Differential gain error 0.03%, @RL=150 Ω
Signal type VGA, SDI, DVI-D, HDMI, Component Video YPbPr and Composite Video CVBS
Video input CVBS YPbPr, VGA SDI DVI HDMI
Interface RCA
Connectors
RCA
Connectors
15-pin HD female
Connectors
BNC
Connectors DVI-D HDMI type A
female Connectors
Analog video signal level
Y signal of Component Video, Composite Video signal: 1 Vp-p
RGB of VGA: 0.7 Vp-p
PbPr signal of Component Video: 0.3 Vp-p
Impedance Analog signals: 75 Ω
HDMI/DVI signal: difference 100 Ω
Return loss -30 dB@5 MHz
Frequency response Horizontal: 30 - 200 KHz
Vertical: 20 - 240 Hz
VGA Video input
Interface 15-pin HD female Connectors
Min./Max. level -2 Vp-p / +2 Vp-p
Impedance 75 Ω
Return loss <-40 dB@5 MHz
Max. DC offset ±5 mV
VGA Sync.
Input level 2.3 Vp-p - 5.0 Vp-p, 3.3 Vp-p, normal
Output level 5.0 Vp-p
Input impedance 3.3 KΩ
Output impedance 75 Ω
SDI output
Interface BNC female Connectors
Signal level 800 mV, standard
Return loss <-15 dB, DC@1 MHz to 1.5 GHz
Impedance 75 Ω

9
Type
S
p
ec. TMX-MV2SDI
HDMI output
Interface HDMI type A female Connectors
Min./ Max. level T.M.D.S. 400 mVp-p
Impedance Difference 100 Ω
Audio
Interface Four 3.8 mm phoenix stereo inputs, a 3.8 mm phoenix stereo output
Gain -30 dB - 0 dB
Frequency response 30 Hz – 20 KHz
THD+N 0.05% @1 KHz
SNR >80 dB
Stereo channel separation >70 dB@1 KHz
CMRR >75 dB@30 Hz - 20 KHz
Impedance Input: >10 KΩ
Output: <10 Ω
Max. input level ≤16 dBu
Max. output level +12 dBu
Control
RS-232 9 pin female D connector
COM Baud rate: adjustable, data: 8 bits, stop: 1 bit, no parity check bit
Interface 2=TX, 3=RX, 5=GND
General spec.
Power supply 100 V AC - 240 V AC, 50/60 Hz
Temperature Operating: 0°C - +40°C
Storage: -40°C - +80°C
Humidity Storage: 10% - 90%
Operating: 10% - 70%
Dimensions w × d × h (mm) 483×208×43 (1U high)
Color gray
Weight 3.3 kg
Mean time between failures 30,000 hours

Appendix：Commendatory assignation
Select the suited input and output resolutions should advance the quality of video image. The following table will list the
assignation of input/output resolutions for TMX-MV2SDI, and who with “√” mark is the better assignation.
1. VGA input and VGA output
Output
Input 800x600p60 1024x768p60 1280x1024p60
800x600p60
1024x768p60
1280x1024p60
√√√
√√√
√√√
2. VGA input and HDMI output
Output
Input AUTO 1280x720p60 1280x720p50 1920x1080p60 1920x1080p50
800x600p60
1024x768p60
1280x1024p60
√√ √
√√ √
√√ √
3. VGA input and SDI output
Output
Input 1280x720p60 1280x720p50 1280x720p30 1920x1080p60 1920x1080p50 1920x1080p30
800x600p60
1024x768p60
1280x1024p60
√√
√√
√√
4. HDMI input and VGA output
Output
Input 800x600p60 1024x768p60 1280x1024p60
1280x720p60
1280x720p50
1920x1080i60
1920x1080i50
1920x1080p60
1920x1080p50
1920x1080p30
√√√
√√√
√√√
10

5. HDMI input and HDMI output
Output
Input AUTO 1280x720p60 1280x720p50 1920x1080p60 1920x1080p50
1280x720p60
1280x720p50
1920x1080i60
1920x1080i50
1920x1080p60
1920x1080p50
1920x1080p30
√√ √
√√√
√√ √
√√√
√√ √
√√√
√
6. HDMI input and SDI output
Output
Input 1280x720p50 1280x720p60 1920x1080p50 1920x1080p60
1280x720p60
1280x720p50
1920x1080i60
1920x1080i50
1920x1080p60
1920x1080p50
1920x1080p30
√
√√
√√
√√
√√
√√
7. DVI input and VGA output
Output
Input 800x600p60 1024x768p60 1280x1024p60
1280x720p60
1280x720p50
1920x1080p60
1920x1080p50
800x600p60
1024x768p60
1280x1024p60
√√√
√√√
√√√
√√√
11

12
8. DVI input and HDMI output
Output
Input AUTO 1280x720p60 1280x720p50 1920x1080p60 1920x1080p50
1280x720p60
1280x720p50
1920x1080p60
1920x1080p50
1024x768p60
1280x1024p60
√√ √
√√√
√√ √
√√√
√√ √
√√ √
9. DVI input and SDI output
Output
Input 1280x720p50 1280x720p60 1920x1080p30 1920x1080p50 1920x1080p60
1280x720p60
1920x1080p60
1024x768p60
1280x1024p60
√√
√√
√√
√√
10. SDI input and VGA output
11. SDI input and HDMI output
Output
Input AUTO 1280x720p60 1280x720p50 1920x1080i60 1920x1080i50 1920x1080p60 1920x1080p50
1280x720p60
1280x720p50
1920x1080p30
1920x1080i60
1920x1080i50
1920x1080p50
1920x1080p60
√√ √ √
√√ √ √
√
√√ √ √
√√ √ √
√√ √ √
√√ √ √
Output
Input 1024x768p60 1280x1024p60
1280x720p60
1280x720p50
1920x1080p30
1920x1080i60
1920x1080i50
1920x1080p50
1920x1080p60
√√
√√
√√

13
12. SDI input and SDI output
Output
Input 1280x720p50 1280x720p60 1920x1080p301920x1080p501920x1080p601920x1080i50 1920x1080i60
1280x720p60
1280x720p50
1280x720p30
1920x1080p30
1920x1080i60
1920x1080i50
1920x1080p50
1920x1080p60
√√
√√√
√
√
√√
√√√
√√√
√√
√
√
√
13. YPbPr input and VGA output
Output
Input 800x600p60 1024x768p60 1280x1024p60
1280x720p60
1280x720p50
√√√
14. YPbPr input and HDMI output
Output
Input AUTO 1280x720p60 1280x720p50 1920x1080p60 1920x1080p50
1280x720p60
1280x720p50
1920x1080p30
1920x1080i60
1920x1080i50
√√ √
√√√
√
√√ √
√√√
15. YPbPr input and SDI output
Output 1280x720p50 1280x720p60 1920x1080p50 1920x1080p60
Input
1280x720p60
1280x720p50
1920x1080i60
1920x1080i50
√√
√√
√√
√√

16. CVBS input and VGA output, not recommend
Output
Input 800x600p60 1024x768p60 1280x1024p60
720x480i60(NTSC)
720x576i50(PAL)
√√√
17. CVBS input and HDMI output, not recommend
Output
Input 1280x720p60 1280x720p50 1920x1080i60 1920x1080i50
720x480i60(NTSC)
720x576i50(PAL)
√√
√√
18. CVBS input and SDI output, not recommend
Output
Input 1280x720p50 1280x720p60 1920x1080i50 1920x1080i60
720x480i60(NTSC)
720x576i50(PAL)
√√
√√
14