Takara Belmont Yume Oasis User manual

1
YUME OASIS Installation Instructions
Contents
Before Installation
Usage Conditions
Preparation Before Installation Of floor unit
YUME OASIS Packing
Installation
Of Floor Unit
Piping In Floor Unit
Carrying The Upper Unit
Connection Check With The Upper Unit
Test Water Flow
Cleaning And Check Of The Floor Unit
Cleaning And Check Of The Upper Unit
After Installation
Specifications
Chair Correlation Dimensioｎ
M E M O
２
５
６
１２
１３
１６
１８
２２
２３
２４
２５
２７
２９
３０
３５
Upper unit
Back Wash Basin
(YUME Basin)
Model No.AY-OAYMYM-*
AY-OAYMYM-*NB
Floor unit
Model No.AY-OAYM-F
Upper unit
Side Wash Basin
Model No.AY-OAYMSS-*
The CAUTIONs listed here are to ensure that YUME OASIS can be installed safely, and to prevent and danger or
risk to the person installing YUME OASIS or those around them.
All of these CAUTIONs are important for safety. TAKARA BELMONT is not responsible for any damage or risk
to the person installing YUME OASIS or those around them due to accidents if YUME OASIS is installed
without adhering to the CAUTIONs.
If YUME OASIS is installed after ignoring this symbol, there is the risk of light or moderate injury or physical damage.
CAUTION
March 20173rd Edition
※The actual shape of YUME OASIS and the images and
dimensions listed in these instructions may be modified
and are subject to change without notice.
To the customers
・Customers must not install YUME OASIS by themselves.
・Please give us your order of installation.
Never install this product by yourself.
・Customers must store these instructions in a safe place
so as not to lose them.
To the installer
・The instructions should be thoroughly read and
understood before installation to ensure that YUME OASIS
is installed correctly.
・After installation, give these instructions to the customer.
TAKARA BELMONT CORPORATION
The "*" part of the individual Model No.
shown above depends on the product color.
The latter of Model No. is without "NB"
This product is battery specification.
Be prepared for AA size battery
(LR6,2 pcs)[not included]

＊1590
30
430
F.L
23 60 135 135
50 65
255
105
105
2
F.L
CAUTION
Before Installation
●Plumbing Drawing
・Vertical Plumbing (Unit: mm)
・Horizontal Plumbing (Unit: mm)
Piping space
Piping space
Drain VU40/VP40
60 or more
Drainpipe
Resin case Resin case
●Always ensure the gradient of drain line according to the number of units to be installed as shown on page 4.
●For vertical plumbing, make sure to adjust the top end of the piping to be lower than the lower end of the resin case.
The space for attaching the stop valve and for piping connection with the floor unit is necessary in the resin case.
●In general, vertical plumbing is recommended when the floor mount pump is fastened.
(The floor-fastening bolt may interfere with the pipe.)
●If horizontal plumbing is necessary, pay careful attention to the interference with the floor-fastening bolt.
●When the floor mount high locks pump (SP-CH) is fastened onto the floor, be aware of the following dimensions:
＊1＝350 mm or more
＊2＝85 mm or less
＊3＝68 mm or less
●In the case of horizontal plumbing, a floor-fastening type pump such as SP-FM, SP-FT and SP-FD cannot be used because
of interference between the pipe and the fastening bolt.
Hot water supply
Water supply
Drain
Center line
Center line
Center line
50以上
590
430
135 135
95
255
23
25 2050 172
50
20
25
35
105
105
F.L F.L
Drain VU40/VP40
＊2
＊3
F.L
65
Hot water supply Rc1/2 13 mm
Water supply Rc1/2 13 mm
Water supply Rc1/2 13 mm
60 to 70 (Distance to the socket end)
45 to 55 (Distance to the socket end)
Hot water supply Rc1/2 13 mm
イス側Seat side
イス側
Seat side

●Plumbing Layout Of Horizontal Plumbing
Stop valve
(accessory)
Flexible hose
(accessory) Drain VU40
Hot water supply Rc1/2
(Copper pipe: 13 mm)
Flexible hose
(accessory)
Flexible hose
(accessory)
Hot water supply Pipe
(Copper pipe of 20 CP or more)
Seat side
Drainpipe
Number of upper units to be used simultaneously
2 units or less; at least VU 50
3 units or more; at least UV 75
3
CAUTION
Pay careful attention to the interference
between the floor-fastening bolt and the
pipe.
Water supply Pipe
(PVC pipe of 20 VP or more,
or Copper pipe of 20 CP or more)
Water supply Rc1/2 13 mm

○Ensure that the material or finishing of the floor surface is waterproof or has a waterproof coating applied.
○Always ensure that the floor surface is horizontally level.
○Ensure that the floor surface is smooth and free from bumps around the attachment areas.
○Prevent the step height of floor joint.
○Be sure to use a floor panel of 3 mm thickness.
○Use a hard floor panel made of polyvinyl chloride (PVC) tiles, etc.
○Do NOT use a cushion floor. Using a cushion floor may cause troubles in detaching and attaching the upper unit.
○For installation of upstairs, make sure to take appropriate waterproof measures.
○Do not use a floor panel with significant bumps or dents that disturb transfer of the upper unit.
○Do not use a floor panel that becomes slippery when water is leaking.
○Use the waterproof material for the floor.
○If the product is installed on the floor above a room, always make sure to take appropriate waterproof measures
(waterproofing work, installation of a stainless steel pan, attachment of a leakage sensor, etc.).
○This company will not bear any responsibility whatsoever for water leakage due to the waterproof installation failure.
■Floor Surface
■Water Leakage
Make sure to prevent the water leakage for the worst.
■Installation Of Pipes
■Plumbing
●Diameter of pipes and gradient of drain line
●Drainpipe end treatment (Ascending part dimensions)
The following are important points to adhere to during the installation of pipes.
Read through the details carefully and ensure that the pipes are installed correctly.
・When installing this product, ensure that installation of pipes adheres to the instructions outlined in "CAUTIONs during
installation of pipes". Installing pipes without reading through the CAUTIONs will mean water may not mix properly,
and a set temperature will not be achieved.
・This product is designed for indoor installation. Always install this product indoors.
Refer to the Plumbing Drawing on page 2.
・Use dependent drainage for YUME OASIS only.
・Layout the drain line in a straight line as best as possible.
Number of upper units to
be used simultaneously Diameter of Drainpipe Gradient of drain line
2 units or less
3 units or more
At least VU 50
At least VU 75
＜CAUTION＞
Use a drainpipe of appropriate diameter according to the
number of units to be installed.
At least 1/100
At least 1/50
4
CAUTION Make sure that the drainpipe does not have double trapping.
Drain failure or abnormal noises may occur.

・Set the hot water temperature to 80℃or less.
・Set the temperature 10℃or higher than the shower temperature used.
5
○Water supply (primary) plumbing
・In the case of using city water direct pressure line, consult to local contractors designated by the water supply
Works Department. Installation must be made in compliance with the plumbing code requirements such as the
"Water Supply Works Department Installation Standard", etc. in your area.
・In the case of using lines other than the city water line (fall supply line from elevated water tank), consult to local
contractors designated by the water supply Works Department. Installation must be made in compliance with the
plumbing code requirements such as the "Water Supply Works Department Installation Standard", etc. in your area.
○Do not use pipes made of materials that may introduce rust for the water supply Pipe.
In general, VP pipes or other materials specified by regulations in that particular region, are recommended for installation.
○In general, Type L deoxidized copper pipes are recommended for hot water pipes.
○In general, the same diameter and same pressure is recommended for hot water pipes and water supply pipes.
○Always use a reamer to demurred the ends of cut pipes.
○Avoid using inverted U-shaped pipes (siphon) as these can cause air to become trapped.
○Always connect hot water pipes and water supply pipes after removing all contaminants such as dirt, sand and oil as these
can cause problems.
○After connecting the pipes and testing water flow, clean the filter and shower head.
○Ensure that the Drainpipe is installed at a gradient of 1/50 for a diameter of φ75 or less, or 1/100 for a diameter of φ75 or
more.
○Do not connect the hot water pipes and water supply pipes in reverse.
Connecting pipes in reverse will mean the temperature of water cannot be controlled properly by the water taps, which can
cause problems including burns.
○Ensure that the hot water pipes from water boilers are only run over a short distance so as to minimize resistance.
Longer pipes can cause fluctuations in temperature and poor hot water delivery.
○Always wrap pipes with lagging material after installation is complete.
○Plumbing particulars for water heater
・In general, the same diameter and same pressure is recommended for main hot water pipes and main water supply pipes.
・Contact a professional for installation of water heater.
○Equipment comes with hair trap installed.
■Hot Water Supply And Water Supply Conditions
Water used
■CAUTIONs During Installation Of Pipes
・Public water supply
(do not use non-drinkable well water or water that contains rust or sand.)
・If the water hardness is 80 ppm or higher, install a water softener to prevent the buildup of scale.
Aeration may be minimal when using shampoo even if drinkable well water is used, so a water
softener should be installed.
・Use a pressure set between 0.1 to 0.4 MPa (1 to 4 kg f/cm2).
If multiple YUME OASIS are used, ensure that the pressure does not drop below 0.1 MPa (1 kg f/cm2).
・Set the water supply pressure ≧hot water supply pressure.
・Set the difference between the hot water supply pressure and water supply pressure to within
0.2. MPa (2 kg f/cm2).
Hot water
temperature
into the product
Hot water supply
temperature
Hot water supply,
water supply
pressure
・For a water heater, TAKARA simultaneous hot water supply system "DANRYU" for barber and
esthetic salon is recommended. Refer to the installation manual of "DANRYU" for installing "DANRYU.”
・Whenusinganinstantaneouswaterheater,theequivalenceofNo.16orbetterisrecommended.
(Shampoo capacity equals to one unit of RS OASIS per one unit of instantaneous water heater.)
・When using a hot water storage system boiler, refer to the installation manual of the boiler.
・A high temperature fluid (steam) that is hotter than the hot water supply specified above may damage the
hot water supply pipe.
Do not connect the hot water supply pipe with a steam generator to cause high temperature steam.
Conditions Of Use