Tatung TME19WE User manual

TFT LCD MONITOR
MODEL:
TME19WE/TME22WE/TME24WE
USER’S
MANUAL

2
TABLE OF CONTENTS
FCC information ---------------------------------------------------------------------- 3
CE information ------------------------------------------------------------------------ 3
Safety Precautions ------------------------------------------------------------------- 3
1. Scope -------------------------------------------------------------------------------------- 5
2. Functional specification ------------------------------------------------------------- 5
3. Controls and indicators -------------------------------------------------------------- 6
4. OSD Menu --------------------------------------------------------------------------------7
5. Mechanical ----------------------------------------------------------------------------- 9

3
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables andA.C. power cord, if any, must be used in order to comply
with emission limits.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE INFORMATION
The product must be installed according to the currently valid installation regulations for
EMC to guarantee the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive,
2014/30/EU & LVD 2014/35/EU
SAFETY PRECAUTIONS
1. Do not modify the three-prong grounding type monitor power plug in any way.
2. Operate this unit only from the type of power source indicated on the label.
3. Do not block or cover ventilation openings on the back or bottom of the monitor
cabinet.
4. Do not place this monitor near a radiator or heating vent.
5. Do not push objects of any kind through cabinet openings. This may result in fire or
electrical shock.
6. Before adding attachments always ask a service technician to perform routine safety
tests to determine that equipment is in safe operating condition. Ground potential tests
should be part of the routine safety check made by the service technician.
7. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure
personnel or damage equipment.

4
8. Route power cords so that they cannot be walked upon or tripped over. Do not allow
anything to rest on the power cord.
9. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not
spill liquid of any kind on the unit.
10.Unplug the power cord from the unit before cleaning the display. Use only a damp cloth.
Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO
CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY
THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.
11.Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY
UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS
VOLTAGES OR OTHER HAZARDS.
12.Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain or
water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician uses
components specified by the manufacturer which have the same characteristics as the
original parts. UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL
SHOCK OR OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to
determine that the equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS
MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE

5
1. Scope
This specification is used to define the performance of
TME19WE/TME22WE/TME24WE color TFT LCD monitor. This system also supports both
BNC input and HDMI input. In BNC mode, the system can automatically detect the NTSC
signal and PAL signal. In HDMI mode, this system can support up to 1920 x 1080 VESA
standard (TME19WE only supports up to 1600x900). The user friendly OSD menu is also
provided to make this system easy to operate.
2 Functional Specifications
2.1 Power Supply
The power supply spec is listed below,
DC INPUT
DC power input range：12VDC
* Power consumption：25W max.
* Power efficiency：80% typical at normal line input and full load
2.2 Video Characteristics
Composite Video (CVBS): 1.0 Vp-p (0.5 –1.5Vpp), Automatic switching from 75 
unbalanced termination to Hi-Z with loop-through operation.
2.3 PC Input
HDMI Input
HDMI Compatible Interface
Digital Signal: TMDS.
HDCP: HDCP 1.1
2.4 Environmental
Temperature
Operating: 00C to +400C
Storage: -200C to +600C
Humidity
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)
2.5 Connectors

6
DC INPUT: Use the supplied 12V DC power supply
HDMI: HDMI Connector
HD Analogue 1 IN: BNC Connector support CVBS/TVI/AHD/CVI
HD Analogue 2 IN: BNC Connector support CVBS/TVI/AHD/CVI
HD Analogue 2 OUT: BNC Connector support CVBS/TVI/AHD/CVI
Set up sequence
1. Make sure the power of PC and/or Video source were turned off.
2. Connect the video signal to monitor.
3. Turns the PC and/or Video source power on.
4. Plug the power supply to DC jack
(Use reverse sequence to teardown the monitor)
3. Controls and indicators
Power - +Menu Source
SOURCE: Select input source –HDA1, HDA2, HDMI.
MENU: Access the On Screen Display (OSD) menu.
＋and －:Controls left/right, Change the size of the value.
POWER: Turns the monitor on or off.
1. To access the OSD Menu press ‘MENU’.
2. Press the ‘SOURCE’ buttons to select the function, then press the ‘＋’or ‘－’button to
select the sub menu.
3. Press the ‘SOURCE’ button to confirm the sub menu, then press ‘＋’or ‘－’to adjust
the setting.
4. Press the ‘MENU’ button to return to previous menu.
5. Press the ‘MENU’ button again to exit the OSD Menu.

7
4. OSD Menu
BNC (HD Analogue) mode：
PICTURE
Picture
Brightness
50
Menu
Contrast
50
Information
Saturation
50
Hue
50
Exit
Brightness: Adjust the image brightness (0-100)
Contrast: Adjust the image contrast (0–100)
Saturation：Adjust the image Saturation (0–100)
Hue: Adjust the image hue (0–100)
MENU
Picture
Language
English
Menu
OSD H Pos.
50
Information
OSD V Pos.
50
OSD Time
20
Reset
>
Exit
Language: OSD language selection
OSD H Pos.: OSD horizontal position adjustment (0-100)
OSD V Pos.: OSD vertical position adjustment (0-100)
OSD Time: OSD display dwell time selection (5-30s)
Reset: OSD setting data recovery factory settings
Information
Picture
Menu
HDA1

8
Information
CVI
720P25
Exit
Display video format, resolution, and frequency of the video signal
HDMI mode：
PICTURE
Picture
Brightness
50
Menu
Contrast
50
Information
Saturation
50
Hue
50
Exit
Brightness: Adjust the image brightness (0-100)
Contrast: Adjust the image contrast (0–100)
Saturation：Adjust the image Saturation (0–100)
Hue: Adjust the image hue (0–100)
MENU
Picture
Language
English
Menu
OSD H Pos.
50
Information
OSD V Pos.
50
OSD Time
20
Reset
>
Exit
Language: OSD language selection
OSD H Pos.: OSD horizontal position adjustment (0-100)
OSD V Pos.: OSD vertical position adjustment (0-100)
OSD Time: OSD display dwell time selection (5-30s)
Reset: OSD setting data recovery factory settings

9
Information
Picture
Menu
HDMI
Information
1080P60
Exit
Display video format, resolution, and frequency of the video signal
5. Mechanical
5.1 Cabinet
Material: Plastic
Finish: Black
5.2 Dimensions
VESA Mount: 100mmx100mm (M4)
Model
Unit
A
B
C
D
E
TME19WE
mm
461.7
275.8
350.6
43.5
127.0
Inch
18.18
10.86
13.80
1.71
5.0
TME22WE
mm
508.0
305.9
379.4
43.3
137.0
Inch
20.0
12.04
14.94
1.70
5.39
TME24WE
mm
555.7
334.4
407.9
46.2
142.0
Inch
21.88
13.17
16.06
1.82
5.59

10
5.3 Dimension (Packing)
- Size
Model
Unit
W
L
H
TME19WE
mm
505
350
110
Inch
19.88
13.78
4.33
TME22WE
mm
548
370
110
Inch
21.57
14.57
4.33
TME24WE
mm
598
400
110
Inch
23.54
15.75
4.33
- Weight: TATUNG COMPANY OF AMERICA,
INC.
LIMITED WARRANTY
COMMERCIAL DISPLAY MONITOR PRODU
Model
kgs
lbs
TME19WE
3.5
7.72
TME22WE
3.75
8.27
TME24WE
4.8
10.58

11
TATUNG COMPANY OF AMERICA, INC.
LIMITED WARRANTY
COMMERCIAL DISPLAY MONITOR PRODUCT
TATUNG COMPANY OF AMERICA, INC.
LIMITED WARRANTY COMMERCIAL DISPLAY MONITOR PRODUCT
Tatung Company of America, Inc. (“Tatung”) warrants to you, the original commercial
purchaser of this new Tatung product (the “product”), that all parts of this product will be
free from defects in materials or workmanship, as hereinafter provided, for three years
from the date of original purchase.
Tatung will, at our option, repair or replace the product or any part thereof which becomes
defective, malfunctions or otherwise fails to conform with this warranty under normal use
and service during the term of this warranty, at no charge to you for parts and labor.
Repaired or replacement products or parts may include remanufactured or refurbished
parts and components. The repaired or replacement product will be covered for the
balance of the time remaining on the product's original limited warranty period.
You may obtain warranty service by contacting Tatung Customer Support at (800)
827-2850, Ext. 242, to obtain a Return MerchandiseAuthorization number (RMA). You will
be required to provide:
- A copy of the dated sales receipt from Tatung (Proof of Purchase).
- Your Name or Company Name
- The model number and serial number of the product
- A description of the problem
- Your ship-to address, email address, fax number and phone number
Upon receipt of the RMA, you can bring or ship the product at your expense to the address
provided with the RMA. Please make sure that the product is packed in a suitable carton
that is large enough and strong enough to allow you to properly secure the product. Tatung
will not be responsible for any loss or damages as a result of shipping in the product for
service, and shipping insurance is recommended to protect you against any loss or
damages resulting from shipping.
TATUNG SHALL NOT BE LIABLE FOR ANY LOSS OR DESTRUCTION OF, OR TO
MAINTAIN THE CONFIDENTIALITY OF, DATA, MEDIA ORANY CONTENT
COMPONENT, SUCH AS PHOTOS, FEEDS, TEMPLATES, ETC., RESULTING FROM
WARRANTY SERVICE OF THE PRODUCT. IT IS YOUR RESPONSIBILITY TO SECURE
AND/OR BACK-UPALL PROGRAMS AND DATA CONTAINED IN OR AFFECTED BY
THE PRODUCT.
This warranty does not cover:

12
1. Defects, malfunction or failures resulting from causes beyond the control of Tatung
or the manufacturer of the product, including, but not limited to, shipping or transit
accident, abuse, misuse, operation contrary to furnished instructions, improper or
insufficient ventilation, operations with incorrect power supplies, operation with
faulty associated equipment, modification, alteration, improper servicing, accidents,
fire, power surges, viruses, malware, acts of God, tampering, reckless, willful or
intentional conduct, or normal wear and tear;
2. Cosmetic damage, such as scratches, plastic discoloration, etc., to the exterior
finish during the warranty period;
3. Burned-in images (screen burn) resulting from viewing of images on the display
screen for an extended period of time;
4. Display problems or reception interference and distortion related to echo,
interference, noise or other signal transmission and delivery/reception problems;
5. Minor display imperfections within the product's design specifications that do not
materially alter functionality;
6. Any reimbursement cost for removal, installation and set-up, including
wall-mounting of product;
7. Products on which the serial number has been altered, defaced or removed; and
8. Products purchased outside of the United States.
Should any product submitted for warranty service be found ineligible for warranty service,
we will provide you with an estimate of cost of repair and will repair the product upon your
request and upon receipt of payment or acceptable arrangements for payment.
WITH RESPECT TO YOU, THE COMMERCIAL PURCHASER, ALL IMPLIED
WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT ARE
EXCLUDED AND DISCLAIMED.
NEITHER TATUNG NOR ITS SERVICE PROVIDER SHALL BE LIABLE FOR ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY. TATUNG’S MAXIMUM LIABILITY IS LIMITED TO
THE PURCHASE PRICE YOU PAID FOR THE PRODUCT PLUS INTEREST AS MAY BE
ALLOWED BY APPLICABLE LAW. TATUNG IS NOT LIABILE TO YOU FOR EVENTS
BEYOND ITS CONTROL, SUCH AS ACTS OF GOD, VIRUSES, PROPERTY DAMAGE,
LOSS OF USE, INTERRUPTION OF BUSINESS, LOST PROFITS, LOST DATA, OR
OTHER CONSEQUENTIAL, PUNITIVE, OR SPECIAL DAMAGES, HOWSOEVER
CAUSED, WHETHER FOR BREACH OF WARRANTY, CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY, OR OTHERWISE

13
TATUNG COMPANY OF AMERICA, INC.
LIMITED WARRANTY
COMMERCIAL DISPLAY MONITOR PRODUCT
This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state. This is the only express warranty applicable to the product; Tatung
neither assumes nor authorizes anyone to assume for it any other express warranty. This
warranty may not be modified, altered, or amended without the written agreement of
Tatung which specifically states that the writing is intended to modify, alter, or amend this
warranty. If any term of this warranty is illegal or unenforceable, the legality and
enforceability of the remaining provisions shall not be affected or impaired.
This warranty extends only to you, the original commercial purchaser, and is not
transferable to anyone who subsequently purchases, leases, or otherwise obtains the
product from you.
TATUNG Co. of America, Inc
2850 El Presidio Street
Long Beach CA 90810
Tel: [phone] x242
www.tatungusa.com
[email protected]m