Taurus MNL214.1 User manual

INDUSTRIAL LCD MONITOR
INSTRUCTION MANUAL - MANUEL D’UTILISATION
MANUALE D’ISTRUZIONE
10.1”
MNL214.1

MNL214.1 2
Index
1GENERAL DESCRIPTION...............................................................................................................3
1.1 INTRODUCTION .............................................................................................................................................3
1.2 NOTES.................................................................................................................................................................3
1.3 WARNINGS .......................................................................................................................................................3
1.3.1 SYMBOLS AND CONVENTIONS ....................................................................................................................... 3
1.3.2 SAFETY ........................................................................................................................................................................ 4
1.4 PRODUCT LABEL............................................................................................................................................4
1.5 LIMITED RESPONSIBILITY DECLARATION ..........................................................................................5
1.5.1 MAINTENANCE AND WARRANTY .................................................................................................................... 5
1.6 CE REGULATION............................................................................................................................................5
1.7 PACKAGING ....................................................................................................................................................5
1.8 TECHNICAL SPECIFICATION ....................................................................................................................6
1.8.1 OPERATING CONDITIONS OF USE..................................................................................................................6
1.9 SUPPORTED INPUT FORMATS....................................................................................................................7
1.10 NAVIGATION KEY............................................................................................................................................7
2OSD MENU SETTINGS................................................................................................................... 8
2.1 MENU “IMAGE’ ...............................................................................................................................................8
2.2 MENU “COLOR” .............................................................................................................................................9
2.3 MENU “COLOR TEMP”.................................................................................................................................9
2.4 MENU “DISPLAY” .........................................................................................................................................10
2.5 MENU “DISPLAY POSITION”....................................................................................................................10
2.6 MENU “SYSTEM”............................................................................................................................................11
3CONNECTORS PIN OUT..............................................................................................................12
3.1 12VDC ALIMENTATION ...............................................................................................................................12
3.2 USB..................................................................................................................................................................... 13
3.3 VGA.................................................................................................................................................................... 13
4OUT OF ORDER AND DISPOSAL...............................................................................................14

MNL214.1 3
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
The 10” LCD Taurus monitor is a professional monitor that allows interfacing of analog signals
(VGA), made with a stainless steel cabinet and built with IP67 protection class. This product can
easily handle watersplashes, shocks and vibrations. The hightechnology andtheir sophisticated
equipment guarantee excellent performance.Thanks to these characteristics, they are suitable
for several applications, such as industrial, food, beverage and many others.
Main features:
• Manual regulation of the movements of the image;
• All the monitors can accept separated syncs, composite syncs and sync on green signals;
• Auto detect of the input signal;
• Auto adjustment function for perfect geometry settings at full screen;
• Energy saving function switches o the monitor in case of missing input signal;
• Full range power supply 24VDC
• OSD functions can be controlled by the control keys on the monitor;
• Resistive, capacitive, SAW touch screens available.
1.2 NOTES
The instructions given in this manual are not a contractual obligation. The warranty conditions
are determined by law. The warranty is normally provided concerning malfunction of the pr
duct and does not cover damages caused by misuse and tampering. All rights are reserved. Any
reproduction or translation of this manual is prohibited without our permission.
1.3 WARNINGS
1.3.1 SYMBOLS AND CONVENTIONS
This symbol alerts the userto the risk of damage to things or loss
of data, if the observations are not respected.
This symbol warns the user of a hazard which may cause serious
injury or death, if the observations are not respected.

MNL214.1
4
1.3.2 SICUREZZA
Read these safety instructions carefully. Keep this user’s manual
forlaterreference and observing all the warnings onthe product
as follow.
• Electric shock hazard – Do not operate the machine with its
back cover removed. There are dangerous high voltages inside.
• Never open the equipment. For safety reasons, only quali
ed service personnel should open the equipment.
• Disconnect this equipment from any outlet before cleaning.
• Before connecting the equipment to the power outlet, make
sure the outlet is grounded according to the laws in force.
The power outlet should also be located as close as possible
to the equipment, so it can be quickly and easily unplugged.
• Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage to things or
harm to people.
• Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
• If the equipment is not used for a long time, disconnect it
from the power source to avoid damages.
Store the equipment according to the temperature and humidity ranges written in this manual.
If any of the following situations arises, get the equipment checked by service personnel: The
power cord or plug is damaged.
• Liquid has penetrated into the equipment;
• The equipment does not work well, or you cannot get it to work;
• The equipment has obvious signs of breakage or damage.
This manual contains all instructions for proper installation and maintenance the product you
purchased. In the box packaging all the support documentation is provided.
1.4 PRODUCT LABEL
All products are identi ed with a production label that shows all the product’s identifying
elements:
• Manufacturer’s mark;
• Production Data;
• Product Model;
• Serial Number;
• Product Description.

MNL214.1 5
Never open the equipment. For safety reasons, only quali ed service
personnel should open the equipment.
Do not use sharp or scratching objects or corrosive substances that
can damage the active surface ofthe touch screen.
1.5 LIMITED RESPONSIBILITY DECLARATION
Any updates to the product could be the cause of updates to this manual, therefore the
manufacturer reserves the right to modify it, in whole or in part, without warning obligation. The
manufacturer also will not accept any liability for damage caused to people or things close to it in
the following cases:
• Misuse of the product and its accessories;
• Improper assembly and installation;
• Unauthorised, modifcation or interventions;
• Using not original spare parts;
• Failure to comply with the rules established by this manual.
Keep the manual with the utmost care in a dry place and protected, always available for future
reference. The manual should be kept as long as the product is in operating life. In case of user’s
manual loss or damage, ask the manufacturer for a new one.
1.5.1 MAINTENANCE AND WARRANTY
The product of this manual does not require any maintenance from the user besides the usual
cleaning of the screen, which must be performed with a speci c non-aggressive, alcohol-free
cleaning agent, sprayed on a soft cloth. For product repair, the user shall contact the manufactur.
1.6 REGOLAMENTO CE
Our products are designed in accordance with the requirements of the Electrical Safety EU di-
rective. 2014/35/UE – LVD LVD (Essential Health and Safety Requirement of the Low Voltage
Directive) And Electromagnetic Compatibility OF THE EU directive2014/30/UE – EMC (Electro-
magnetic Compatibility Directive) in order to a x the CE mark, in relation to standards:
• CEI EN 60950-1 Electrical Safety
• CEI EN 55024 – CEI EN 55022 Electromagnetic Compatibility
1.7 PACKAGING
The PACKAGING is composed by a cardboard box with inside expanded material shells that
guarantee safety during the shipment by carriers.
• TFT;
• Documentation (This manual);
• Connection cables.

MNL214.1
6
1.8 TECHNICAL SPECIFICATION
• Class protection IP65 or IP67: Compliant with CEI EN 60529
• Food sector safety: In accordance whit (CE) N 1935/2004
• ON materials and articles entended to come into contact whit food an articles repealing
directives. 80/590/CEE e 89/109/CEE
• Material used for the case: AISI304 or AISI316 (Optional)
Power supply input:
12Vdc With external adapter 100/240Vac
Power consumption:
15W.
Frequency range:
• Horizontal Sync. Frequency: 30 – 60 KHz Multisync;
• Vertical Sync. Frequency : 56 – 75 Hz.
VGA Standard input signals:
RGB analogico, 0.7 ~ 1Vpp level ON 75 ohm impedance HD15F
(vedere la sezione “INPUT SOURCE”).
Supported resolutions:
• VGA/SVGA/XGA/SXGA/WUXGA 60Hz;
• Plug & Play ;
• Separated / composite syn;
Supported video signal input:
• VGA Plug & Play.
1.8.1 OPERATING CONDITIONS
Operating conditions:
• Temperature: 0°C +50°C
• Humidity: 10% - 95%
• Altitude: 0 - 3000
Storage conditions:
• Temperature: -10°C +55°C
• Humidity: 5% - 95%
• Altitudine: 0 - 3000m
Shipment conditions:
• Temperature: -35°C +60°C
• Humidity: 5% - 95%
• Altitude: 0 - 12000m

MNL214.1 7
Mode Resolution Refresh Rate H-Frequency Pixel freq. Remarks
VGA 640 X 350 70 Hz 31.47 KHz 25.175 MHz VESA STD
VGA 720 X 400 59.940 Hz 31.469KHz 25.175 MHz IBM VGA 3H
VGA 640 X 480 60 Hz 31.5 KHz 25.175 MHz Industry STD
VGA 640 X 480 72 Hz 37.9 KHz 31.5 MHz VESA STD
VGA 640 X 480 75 Hz 37.5 KHz 31.5 MHz VESA STD
SVGA 800 X 600 60 Hz 37.9 KHz 40 MHz VESA Guid.
SVGA 800 X 600 72 Hz 48.1 KHz 50 MHz VESA STD
SVGA 800 X 600 75 Hz 46.9 KHz 49.5 MHz VESA STD
XGA 1024 X 768 60 Hz 48.4 KHz 65 MHz VESA Guid.
XGA 1024 X 768 70 Hz 56.5 KHz 75 MHz VESA STD
XGA 1024 X 768 75 Hz 60 KHz 78.75 MHz VESA STD
SXGA 1280 X 1024 60 Hz 64 KHz 108 MHz VESA STD
SXGA 1280 X 1024 75 Hz 80 KHz 135 MHz VESA STD
WXGA 1280 X 768 60-75 Hz 47.7-65 KHz 80.14 MHz NOT STD
WXGA 1366 X 768 60-75 Hz 47.7-65 KHz 80 MHz NOT STD
WSXGA 1440 X 900 60-75 Hz 65 KHz 150 MHz NOT STD
WSXGA 1680 X 1050 60 Hz 70 KHz 150 MHz NOT STD
UXGA 1600 x 1200 60 Hz 75 KHz 162 MHz NOT STD
* FULL HD 1920 x 1080 60 Hz 69 KHz 138 MHz NOT STD
* WUXGA 1920 x 1200 60 Hz 69 Hz 154 MHz NOT STD
1.9 SUPPORTED INPUT SIGNALS
1.10 NAVIGATION KEY
Menu Navigation Key:
• “Menu/ enter”= Menu & Enter Key;
• “Down” = Down Key / Auto con g;
• “ - ”= Decrease Key / Left Key;
• “+”= Increase Key / Right Key;
• “SRC / Exit”= Source Select / Exit;
• “Power”= ON / ST-by Monitor.
Osd menu function
Press “MENU” button on navigation key, set rear the monitor to display OSD Menù on screen.

MNL214.1
8
2 SETTAGGI SU MENU PER CHIPSET GRAFICO STDP 6038
2.1 MENU IMAGE
• Brightness: brightness adjust;
• Contrast: contrast adjust;
• Sharpness: sharpness adjust;
• Color: go to color menu;
• “SRC / Exit” of external OSD keyboard: exit menu.
Example

MNL214.1 9
2.2 MENU “COLOR”
• Auto (RGB only): automatically set the color to a standard;
• Color Temp: go to Color Temp menu;
• Full Color: lets you adjust the default FULL COLOR;
• SRGB: lets you adjust the color space sRGB;
• “SRC / Exit” of external OSD keyboard: go back to previous menu.
Example
2.3 MENU “COLOR TEMP”
• Set the color temperature;
• User: primary colors intensity adjust;
• “SRC / Exit” of external OSD keyboard: go back to previous menu.

MNL214.1
10
2.4 MENU DISPLAY
• AUTO: image adjust;
• Phase: adjust the Phase of the image;
• Frequency: adjust the signal frequency for improve image quality;
• Display Position: go to the Move Position menu;
• “SRC / Exit” of external OSD keyboard: go back to main menu.
2.5 MENU “DISPLAY POSITION”
• Move the image Horizzontally and vertically.