TC Electronic TonePrint Editor User manual

Manual
TC Electronic
TonePrint Editor

Table of contents
a
About this manual 1
Welcome! 2
So… what’s in a TonePrint? .............. 2
TonePrint Editor’s resumé ................ 2
What you will need ..................... 2
Getting started 3
Ready…. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Set… ................................ 3
TonePrint! ............................ 3
Precautions:
Don’t lose that TonePrint! ................ 4
Different pedals, different parameters....... 4
Multiple TonePrint pedals – one editor ...... 4
Pedal serial and software
version information ..................... 5
Your sound:
There’s a template for that! ............... 5
Using TonePrint Editor 6
Template TonePrint ..................... 6
Returning to template defaults 6
Router section ......................... 6
Kill Dry parameter 6
Knob Selection section .................. 6
Assigning parameters to a knob 7
Modifier display ........................ 7
Modifier sections 9
Modulation parameters 10
Modulation Type selector ............... 10
Classic Chorus setting 10
Advanced Chorus setting 10
Classic Flanger setting 10
Advanced Flanger setting 10
Vibrato setting 10
TriChorus setting 10
TriChorus Alternative setting 10
TZFlanger (“Through zero”) setting 10
Modulation Active parameter............. 10
Through-Zero-Flanger parameter ......... 11
Speed parameter...................... 11
Depth 1 parameter .................... 11
Depth 2 parameter .................... 11
Depth 3 parameter .................... 11
HiCut parameter ...................... 11
Mix parameter ........................ 11
Output Level parameter. . . . . . . . . . . . . . . . . 11
Delay Time 1 parameter ................ 11
Delay Time 2 parameter ................ 11
Delay Time 3 parameter ................ 12
Feedback parameter ................... 12
Feedback HiCut parameter .............. 12
Vib. Ramp Time parameter .............. 12
Delay parameters 13
Delay Time parameter .................. 13
Feedback parameter ................... 13
Saturation parameter................... 13
FB HiCut (Feedback
High-Cut) parameter ................... 13
FB LoCut (Feedback
Low-Cut) parameter ................... 13
Output Level parameter. . . . . . . . . . . . . . . . . 13
Dynamic Delay
Sensitivity parameter................... 13
Damping parameter.................... 14
Release Time parameter ................ 14
Reverse Delay Time parameter .......... 14
Reverb parameters 15
Decay parameter...................... 15
PreDelayShort parameter ............... 15
PreDelayLong parameter ............... 15
Diffuse parameter ..................... 15
LoColor parameter .................... 15
HiColor parameter ..................... 15
HiFactor parameter .................... 15
Mod On/Off parameter ................. 15
Modulation Rate parameter.............. 15
Modulation Depth parameter............. 15
Early parameter....................... 16
Reverb parameter ..................... 16
Dynamix Mode switch .................. 16
Off setting 16
Positive mode 16
Inverse mode 16
Dynamix Threshold parameter ........... 16
Dynamix Damp parameter .............. 16
Dynamix Attack parameter .............. 16
Dynamix Release parameter............. 16
Updating TonePrint Editor 17
Getting support 17

■About this manual
TC Electronic TonePrint Editor ■Manual for software version 1.0 1
About this manual
This manual will help you learn understanding
and operating TonePrint Editor (and all the TC
pedals you can control with it).
This manual is only available as a PDF download
from the TC Electronic website.
You can print this manual, but we encourage you
to use the PDF version, which has both internal
and external hyperlinks. E.g., clicking the blue
square ■in the upper left corner of each page will
take you to the table of contents.
If you want to jump right in, click into an in-
terface section in the illustration to the right
to go directly to the corresponding section of
this manual.
To get the most from this manual, please read it
from start to finish, or you may miss important in-
formation.
To download the most current version of this man-
ual, visit the web page
http://www.tcelectronic.com/support/manuals/

■Welcome!
TC Electronic TonePrint Editor ■Manual for software version 1.0 2
Welcome!
So… what’s in a TonePrint?
We should probably start by telling you what
TonePrint actually means.
TonePrint means… signature effects. These are
custom-built versions of classic TC effects, avail-
able for our TonePrint pedals. But we’re not talk-
ing simple presets here – we’re way past that!
TonePrints are custom-tuned sounds, built by the
best of the best in modern music from the ground
up – with every parameter, knob range and effect
value up in the air!
We have asked the very best guitarists and bass
players to give us their personal take on TC ef-
fects as they use them live and in the studio, and
they have come up with sounds that truly repre-
sent their personality, their sonic DNA.
TC customers have been able to download,
use and enjoy these TonePrints for years. But
now it’s time for a new chapter. Now it’s your
turn to create your very own signature effects.
Take a TC pedal, take a TonePrint, take TonePrint
Editor – and make it your own.
TonePrint Editor’s resumé
■Use TonePrint Editor to build your own custom
version of renowned TC Effects from scratch.
■Enjoy complete control over all effect para-
meters and effect behavior – it’s your vision,
sound.
■Customize knob functions and knob ranges to
suit your needs and sounds.
■Use an intuitive, slider-based interface.
■Audition your sonic creations in real-time.
Make changes on the fly and listen to results
immediately.
■Works with both PC and Mac.
■Last but not least…
TonePrint Editor is absolutely free!
What you will need
■A TonePrint-enabled effects pedal.
■An instrument and an amplifier so you can
play and listen to your sonic creations.
■A computer running Microsoft Windows or
Apple’s OS X (i.e., a Mac).
■PC requirements:
Windows XP (with SP2), Vista, Win 7 or
Windows 8
■Mac requirements:
An Intel-based Mac running OS X version
10.5 or higher
■A USB cable (type A Male to Mini B Male) to
connect your computer and your TonePrint-en-
abled TC product.

■Getting started
TC Electronic TonePrint Editor ■Manual for software version 1.0 3
Getting started
Ready…
If you haven’t already done so, download the lat-
est TonePrint Editor software from:
http://www.tcelectronic.com/toneprint-editor/
TonePrint Editor software is free.
Install TonePrint Editor.
■To install the PC (Windows) version, simply
move the .exe file you downloaded to a loca-
tion on your hard disk.
■To install the Mac (OS X) version, open the
.DMG file you downloaded. From the disk im-
age, copy TonePrint Editor.app to your applica-
tion folder or any other location where you can
easily find it.
Set…
■Set up your TC pedal as you normally would:
■Connect your instrument to the audio in
jack(s) of the pedal,
■ connect the audio out jack(s) of the pedal to
your amp and
■connect the pedal to a power supply.
■Make sure you’ve got a basic sound (and a
sound level) you’re comfortable with, with the
effect bypassed.
■Turn the effect on.
■Connect your pedal to your computer using the
type A Male to Mini B Male USB cable.
Please note that you can only connect and
control one TonePrint-enabled product at
a time, even if your computer has multiple
USB ports.
■Using its Type Selector, switch your pedal to
the TonePrint slot you want to use.
■Open TonePrint Editor on your computer.
TonePrint!
When you have opened TonePrint Editor on your
computer with a TonePrint-enabled TC product
connected to it, TonePrint Editor should automati-
cally detect the connected device and show you
a graphical representation of its parameters on
screen.
If you see a splash screen saying that you
should connect a TonePrint pedal, your pedal
has not been detected. Make sure it is powered
up and connected to your computer via USB.
Once your pedal has been detected, you are
ready to create your very own TonePrints. Here is
how it basically works:
TonePrint Editor exposes the internal parameters
of a TonePrint-enabled pedal. Use the on-screen
sliders of TonePrint Editor to adjust the effect’s
parameters.
These sliders allow you to create a customized
version of a renowned TC effect that you can call
your own. From subtle variations to extreme mod-
ifications that will fundamentally alter an effect’s
character and behavior: The choice is yours!

■Getting started
TC Electronic TonePrint Editor ■Manual for software version 1.0 4
Precautions:
Don’t lose that TonePrint!
When editing TonePrints, there are two things that
you should always keep in mind:
■When you are done editing, always remember
to store your TonePrint to the pedal using
the “Store to Pedal” button! If you don’t, you
will lose your creation when you disconnect the
pedal.
■You can use the knobs on your pedal in real-
time, and the parameters will follow on-screen,
but whatever you do: Don’t change the Type
Selector away from the TonePrint slot, and
do not disconnect power while editing without
saving.
Different pedals,
different parameters
No two TonePrint-enabled pedals are alike – but
different pedal types share certain parameters
such as “Speed” and “Depth”.
With delay and reverb TonePrints, you can also
add modulation to the effect. The interface for
reverb/delay modulation is the same as for the
pedals dedicated to modulation effects.
This is why this manual has three parameter-re-
lated sections:
■The first section covers all modulation-related
parameters in TonePrint Editor.
■The second section covers all parameters re-
lated to delay TonePrints.
■The third section is dedicated to all parameters
of reverb TonePrints.
Multiple TonePrint pedals –
one editor to rule them all
You own more than one TonePrint-enabled ped-
al? That’s great! Just connect the pedal you want
to configure to your computer using a USB cable,
and the user interface will update immediately.
However, please note that no matter how many
USB ports your computer has, you can only ac-
cess one TonePrint-enabled pedal at a time.
You can connect and disconnect pedals to your
computer via USB even while TonePrint Editor is
running. To edit TonePrints and store a Tone-
Print to a pedal, the pedal must be connected
to a power supply. No power is supplied to the
pedal via your computer’s USB port.

■Getting started
TC Electronic TonePrint Editor ■Manual for software version 1.0 5
Pedal serial and software
version information
When a TonePrint-enabled pedal is connected to
your computer and you click the small “i” icon in
the lower left corner of the TonePrint Editor win-
dow, a dialog box will show the following informa-
tion:
■Device serial number
■Device firmware build number
■TonePrint Editor software version number
■TonePrint Editor software build number.
Your sound:
There’s a template for that!
We know: Going from a handful of knobs on a
pedal to a screen full of sliders can be a bit tricky,
and you may be intimidated by the idea of creat-
ing a TonePrint from scratch. This is why we have
provided you with Template TonePrints.
These templates allow you to load a base Tone-
Print and customize it instead of starting with a
blank slate. These templates are great for sketch-
ing out quick ideas, infusing your own concepts,
tweaks and preferences. If you are new to effects
and sound design, they will also give you an idea
of how a typical effect is set up.
Finally, if you got a bit overexcited and you find
that you are stuck with a TonePrint that just
doesn’t sound or work as it should, a Template
TonePrint can be your get-out-of-jail-free card.

■Using TonePrint Editor
TC Electronic TonePrint Editor ■Manual for software version 1.0 6
Using TonePrint Editor
Template TonePrint
As described on the previous page, TonePrint
Templates are a great way of starting your per-
sonal sound creation, as they give you time-prov-
en defaults for all parameters.
To recall a template, select it from the menu.
Please note that selecting a template will immedi-
ately override all changes you might have made
to knob assignments, modifier curves and param-
eter values.
Returning to template defaults
If you find that you have reached a dead end
when editing, you can simply click the Reload
button next to the Template menu to reset the cur-
rently selected template to its default values. This
will reset all knob assignments, modifier curves
and parameter values to the defaults stored in
this template.
Router section
Kill Dry parameter
Settings: Off/On
Use the Kill Dry parameter to define wether your
instrument’s dry, unprocessed signal should pass
through the pedal. Setting Kill Dry to On will mute
the dry signal of your instrument. This is espe-
cially useful for reverse delay effects and vibrato
effects – but you may find other, creative uses for
this parameter.
Knob Selection section
In the knob selection section, you can assign dif-
ferent functions to your pedal’s knobs, so they
control exactly what you want them to control.
But there’s more here than simple 1:1 assign-
ments! You can assign two or even three func-
tions to one knob, allowing you to change multiple
parameters by using just one control. This allows
for very efficient control and dramatic changes, if
this is what you want to achieve.
Finally, you can scale and limit the way a knob
controls a parameter you have assigned to it.
Let’s say that a parameter that you want to con-
trol has a range from 0 to 100 %. Turning the re-
spective knob to the minimum position will set the
parameter to 0 %, and the maximum position rep-
resents 100 %. But what if the “sweet spot” lies
between 25 and 50 %?

■Using TonePrint Editor
TC Electronic TonePrint Editor ■Manual for software version 1.0 7
With TonePrint Editor, you decide what parameter
range you want to control, and how the knob’s po-
sition should affect it. If you want to, you can even
use the knob range left of the center position to go
from 0 to 100 % – and then back to 25 % when
turning the knob all the way clockwise.
Assigning parameters to a knob
■Start by selecting a knob in the Knob Selection
section.
The selected knob will be highlighted.
■Select one of the three yellow, red and blue
“LEDs”.
The selected LED will be highlighted.
■Select a parameter you want to control from
the drop-down menu to the left of the LED.
■Turn the knob to see its current position high-
lighted in the graphical “Peak Performance” in-
terface.
As you can see, you can assign up to three pa-
rameters to a knob. The currently selected pa-
rameter will be highlighted in the display, with the
other parameters still visible in the background.
Scaling the selected parameter is described in
the next section of this manual.
Modifier display
In the upper left part of the TonePrint Editor win-
dow is small graphical interface where effect val-
ues assigned to the currently selected knob are
represented by “peaks” and “valleys”. This display
is your key to understanding and controlling the
way your pedal’s knobs control effect parameters.
Before you can define the relationship between
knob positions and parameter values, you have
to select the parameter in the Knob Selection
section.
Once you have selected a parameter, the modi-
fier curve for that parameter will be shown in the
Modifier display. By default, this is a straight line
from the parameter’s lowest value in the lower left
corner to the maximum value in the upper right
corner.

■Using TonePrint Editor
TC Electronic TonePrint Editor ■Manual for software version 1.0 8
To modify the curve, you can either drag one of
the circle-shaped control points of the modifier
curve, or you can select one of the numerical val-
ues shown right below the display and enter the
desired value manually.
As you can set the modifier curve separately for
each of the three parameters that each knob can
control, you could make a knob on your pedal in-
crease one parameter’s value as you turn it clock-
wise while decreasing another parameter’s value
at the same time.
We suggest playing your instrument and turning
the currently selected knob to get a better un-
derstanding of the way that knobs and modifier
curves interact.

■Modifier sections
TC Electronic TonePrint Editor ■Manual for software version 1.0 9
Modifier sections
Use the parameters displayed in the right-hand-
side section of the TonePrint Editor window to set
the parameters that define your TonePrint.
This is the heart of your TonePrint – the place
where you define your sound.
Please note that what you are seeing here de-
pends on the type of TonePrint pedal connected.
With a modulation-only pedal, you will only see
the “Modulation” section. Reverb and delay ped-
als will also show a Modulation section, as de-
scribed in “Different pedals, different parameters”
(page 4).
If you have worked with effect processors (ei-
ther hardware or software) before, this part of the
TonePrint Editor window should look familiar. This
is an elegant, slider-based interface with a “what
you see is what you get” approach: Change a pa-
rameter, and both the display and what you are
hearing will immediately reflect the new setting.
In the following sections of this manual, we will
present and explain the parameters of the three
sections: Delay, Reverb, and Modulation.

■Modulation parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 10
Modulation parameters
Use the parameters in the Modulation part of the
TonePrint Editor window to configure the modula-
tion effect.
Modulation Type selector
Use the Modulation Type selector to select be-
tween the following types of modulation effects:
Classic Chorus setting
This is the standard chorus inspired by the le-
gendary TC Stereo Chorus Flanger.
The basic idea of a chorus effect is to split the sig-
nal and pitch-modulate one of the signals slightly,
and then mix the two signals again.
Advanced Chorus setting
The Advanced Chorus setting is a variation of the
Chorus setting where the parameters defining the
chorus effect are tuned slightly differently.
Classic Flanger setting
The flanger belongs to the same “family” of mod-
ulation effects as the chorus effect. The signal is
split, and one of the signals is pitch modulated.
The characteristic “flanging” sound occurs when
part of the signal is slightly delayed and fed back
to the input of the effect algorithm. Experiment
with the Feedback parameter to get a feeling for
the achievable effects.
Advanced Flanger setting
The Advanced Flanger setting is a variation of the
Flanger setting where the parameters defining the
flanger effect are tuned slightly differently.
Vibrato setting
A vibrato effect modulates the pitch of the incom-
ing signal. The result is similar to the vibrato tech-
nique used by vocalists.
As opposed to a chorus effect, no direct signal is
combined with the vibrato effect’s pitch-modulat-
ed signal.
TriChorus setting
The TriChorus is a variation of the regular cho-
rus that uses three stereo chorus modules with
various offsets for the Depth, Speed, Phase and
Chorus Delay time parameters. The result is a
unique, very broad and lush sound. Speed, Depth
and Time parameters are identical to those in the
standard Chorus.
TriChorus Alternative setting
The TriChorus Alternative setting is a variation of
the TriChorus setting where the parameters defin-
ing the modulation parameters of the three cho-
rus modules are tuned to produce a wilder and
“less controlled” Chorus effect.
TZFlanger (“Through zero”) setting
The TZF Mode Flanger emulates the original way
of creating a flange effect where two identical
pieces of audio material were played back simul-
taneously on two tape decks and then mixed on
a third deck. The “flanging” effect was achieved
by slowing down and speeding up the two decks
at different times. An essential part of this setup
is the unique phase cancellation occurring when
the two signals pass each other in time (the “zero
point”).
When you set the Modulation Type parameter
to TZFlanger, the input signal is split up so that
delay line 1 becomes the “dry” part of the signal.
This is why you should set the Kill dry parameter
to On when setting the Modulation Type param-
eter to TZFlanger.
Modulation Active parameter
Settings: On/Off
Use the Modulation Active parameter to switch
the modulation effect on or off. This is especially
useful for activating the modulation engine when
working with delay and reverb TonePrints. How-
ever, you also need to set this parameter to On
for regular modulation effects.

■Modulation parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 11
Through-Zero-Flanger parameter
Parameter range: 0 to 1023
When you set the Modulation Type parameter to
TZFlanger, delay line 1 becomes the “dry” part of
the signal. In that case, use the Through-Zero-
Flanger parameter to set the level ratio between
delay line 1 and delay line 2.
Speed parameter
Parameter range: 61.5 mHz (Millihertz) to 20 Hz
Use the Speed parameter to set the speed of
the chosen modulation effect. As setting of 1 Hz
means that one modulation cycle takes one se-
cond.
Depth 1 parameter
Parameter range: 0 to 100 %
Use the Depth 1 parameter to specify the inten-
sity of the effect. The value represents the ampli-
tude of the waveform modulating the signal.
When you have set Modulation Type to TZFlang-
er, you should set the Depth 1 parameter to a
value lower than Depth 2.
Depth 2 parameter
Parameter range: 0 to 100 %
The Depth 2 parameter is only applicable when
you have set Modulation Type to TriChorus or
TZFlanger.
In TriChorus mode, the Depth 2 parameter speci-
fies the intensity of the second chorus module. In
TZFlanger mode, the Depth 2 parameter speci-
fies the intensity of the second flange module.
The value represents the amplitude of the second
waveform modulating the signal.
Depth 3 parameter
Parameter range: 0 to 100 %
The Depth 3 parameter is only applicable when
you have set Modulation Type to TriChorus.
In TriChorus mode, the Depth 3 parameter speci-
fies the intensity of the third chorus module.
The value represents the amplitude of the third
waveform modulating the signal.
HiCut parameter
Parameter range: 20 Hz to 20 kHz
Use the HiCut parameter to reduce the high-end
frequencies in the modulation effect. Try using
this parameter if you feel the effect is too domi-
nant in your sound and turning down the Mix or
Output Level parameters doesn’t attenuate the
effect as intended.
Mix parameter
Parameter range: 0 to 100 %
Use the Mix parameter to set the relationship be-
tween the level of the dry signal and the level of
the modulation effect. If you have set Kill dry in
the Router section to On, this parameter has no
effect.
Output Level parameter
Parameter range: -100 to 0 dB
Use the Output Level parameter to set the overall
output level for the modulation effect.
Delay Time 1 parameter
Parameter range: 0.1 to 50 ms
As described earlier, a chorus or flanger is basi-
cally a delay being modulated by an LFO. Use
the Delay Time 1 parameter to change the length
of that delay. A typical chorus uses delay times
around 10 ms, while a flanger uses delays around
5 ms.
Although this is not how a chorus is normally
used, you may enjoy the “slap-back” sound re-
sulting from longer Delay Time values in the 30
to 50 ms range.
Delay Time 2 parameter
Parameter range: 0.1 to 50 ms
The Delay Time 2 parameter is only applicable
when you have set Modulation Type to TriChorus
or TZFlanger.
In TriChorus mode, the Delay Time 2 parameter
specifies the length of the delay for the second
chorus module.
In TZFlanger mode, the Delay Time 2 parameter
specifies the length of the delay for the second
flange module.

■Modulation parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 12
Delay Time 3 parameter
Parameter range: 0.1 to 50 ms
The Delay Time 3 parameter is only applicable
when you have set Modulation Type to TriChorus.
In TriChorus mode, the Delay Time 3 parameter
specifies the length of the delay for the third cho-
rus module.
Feedback parameter
Parameter range: -100 to 100 %
Use the feedback parameter to define the amount
of the signal that is fed back from the modulation
module’s output to its input.
Experiment with the Feedback parameter to get a
feeling for the effects you can achieve.
Feedback HiCut parameter
Parameter range: 20 Hz to 20 kHz
Use the Feedback HiCut parameter to attenuate
the high-end frequencies of the resonance cre-
ated with the Feedback parameter.
Vib. Ramp Time parameter
(Shaker Vibrato only)
Parameter range: 1 to 5000 ms
The Vib(rato) Ramp Time parameter is only avail-
able and editable when a Shaker Vibrato pedal is
connected.
The Vibrato Ramp effect is a subtype of the vi-
brato effect where the effect is latched – i.e., the
effect will only be applied when you press and
hold the pedal’s footswitch. The Vibrato Ramp
Time parameter sets the time that is required for
the vibrato effect to build up.

■Delay parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 13
Delay parameters
Use the parameters in the Delay part of the Tone-
Print Editor window to configure the delay effect.
Delay Time parameter
Parameter range: 0 to 7000 ms
Use the Delay Time parameter to set the time be-
tween delay repetitions. This is also known as the
“length” of the delay.
Feedback parameter
Parameter range: 0 to 120 %
Use the Feedback parameter to define the amount
of the signal that is fed back from the delay mod-
ule’s output to its input. This parameter defines
how many repetitions of the original signal the
delay will create.
Please use high settings with extreme caution.
Due to the Spillover feature, there is no way to
immediately cut off the delay when you get an
internal feedback at settings above 100 %. This
means that the delays will increase in volume
until there is severe distortion. If this occurs, you
will need to reduce feedback by turning down the
knob assigned to the Feedback parameter, or by
simply turning off the effect until things have set-
tled down again.
Saturation parameter
Parameter range: 0 to 24 dB
Use the Saturation parameter to add a bit of
signal saturation to your delays. This is recom-
mended if you want to add a touch of “grit” to a
TonePrint.
Using saturation will bring you closer to the sonic
qualities of old school analog or tape delay units
with the slight distortion that occurs when driven a
bit harder. The saturation of the delayed signal is
similar to playing through a cranked-up amp. Hit-
ting the strings harder will give you a more over-
driven delay sound than playing softly.
FB HiCut (Feedback
High-Cut) parameter
Parameter range: 20 Hz to 20 kHz
Use the FB HiCut (Feedback High-Cut) param-
eter to attenuate the frequencies over the set fre-
quency for the delayed signal, resulting in a more
“analog” sound that in many cases that will blend
in better with the overall sound.
With digital technology, every delay can be a
precise reproduction of the input signal. But es-
pecially with long delay times, this is not always
desirable, as these pristine delays may disturb
the original signal, resulting in a “washed-out”
sound. To compensate for this, use the high-cut
filter, thereby emulating analog or tape style de-
lay units.
FB LoCut (Feedback
Low-Cut) parameter
Parameter range: 20 Hz to 20 kHz
Use the FB LoCut (Feedback Low-Cut) param-
eter to attenuate the frequencies below the set
frequency.
As with the Feedback High-Cut parameter, the
delays may blend in more nicely with the overall
sound if you “thin out” the effect at the low end.
Output Level parameter
Parameter range: -100 to 0 dB
Use the Output Level parameter to set the overall
output level for the delay effect.
Dynamic Delay
Sensitivity parameter
Parameter range: -50 to 0 dB
The Dynamic Delay is a feature that was initially
introduced in the well-recognized TC 2290. It al-
lows the dynamics of the input signal’s level to
actively alter the delay output level, leaving the
source signal clear and undisturbed while you
play. The Dynamic Delay delicately complements
your performance.
Use the Dynamic Delay Sensitivity parameter to
set a “level limit”. If what you are playing is louder
than this setting, it will dampen the level of the
delay. If what you are playing is softer than this
setting, the delay will be audible.

■Delay parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 14
You will notice that dynamic delays work great
with almost every kind of delay – from analog
tape echoes to pristine 2290 sounds.
Damping parameter
Parameter range: 0 to 100 dB
Use the damping parameter to set the amount of
attenuation that should occur when the input sig-
nal is higher than the level limit you have set with
the Dynamic Delay Sensitivity parameter.
Release Time parameter
Parameter range: 20 to 1000 ms
Use the Release Time parameter to set how fast
the attenuation of the delay repetitions is released
once the input signal falls below the limit you have
set with the Dynamic Delay Sensitivity parameter.
Reverse Delay Time parameter
Parameter range: 50 to 7000 ms
Originally, reverse delay effects were created by
recording a signal on tape, then flipping (revers-
ing) the tape and playing it backwards.
Use the Reverse Delay Time parameter to emu-
late this reverse tape delay effect. This parameter
defines how long a signal is being recorded be-
fore the virtual tape is “flipped over” and played
back.

■Reverb parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 15
Reverb parameters
Use the parameters in the Reverb section of the
TonePrint Editor window to configure the reverb
effect.
Decay parameter
Parameter range: 0.01 to 20 s
Use the Decay parameter to set the decay time of
the Reverb in seconds. The decay time is usually
associated with the time it takes the diffuse field
of a reverb to decay to -60 dB.
PreDelayShort parameter
Parameter range: 0 to 100 ms
The PreDelayShort parameter is only applicable
when the Pre-Delay switch on the pedal has been
set to the “Short” setting.
Use the PreDelayShort parameter to define a
short delay placed between the direct signal and
the Reverb’s diffuse field. Use the PreDelayShort
parameter to keep the source material clear and
undisturbed from the scattered diffuse field of the
Reverb arriving shortly after.
PreDelayLong parameter
Parameter range: 0 to 100 ms
The PreDelayLong parameter is only applicable
when the Pre-Delay switch on the pedal has been
set to the “Long” setting.
Use the PreDelayLong parameter to define a
short Delay placed between the direct signal and
the Reverb’s diffuse field. Use the PreDelayLong
parameter to keep the source material clear and
undisturbed from the scattered diffuse field of the
Reverb arriving shortly after.
Diffuse parameter
Parameter range: -50 to 50
Use the Diffuse parameter to fine-tune the density
of the reverb’s diffuse field. It allows you to reduce
flutter in the diffuse field to an absolute minimum.
LoColor parameter
Parameter range: -50 to 50
Use the LoColor parameter to adjust the low fre-
quency spectrum of the output signal. This can be
used for altering the overall color of the reverb.
HiColor parameter
Parameter range: -50 to 50
Use the HiColor parameter to adjust the high fre-
quency spectrum of the output signal. This can be
used for altering the overall color of the reverb.
HiFactor parameter
Parameter range: -25 to 25
Use the HiFactor parameter to emphasize or at-
tenuate the selected HiColor value.
Mod On/Off parameter
Use the Mod On/Off parameter to switch modula-
tion of the reverb signal on or off.
The algorithm designers at TC have adjusted the
diffuse field part of the reverb to be as smooth
and natural sounding as possible. Adding in mod-
ulation to the reverb tail allows for interesting ef-
fects that can be refined using the Modulation
Rate and Modulation Depth parameters.
Modulation Rate parameter
Parameter range: -25 to 25
Use the Modulation Rate parameter to offset the
speed of the LFO that is being used to modulate
the Reverb.
This parameter only has an effect when you have
set the Mod On/Off switch to On.
Modulation Depth parameter
Parameter range: -25 to 25
Use the Modulation Depth parameter to offset the
intensity of the modulation that is applied to the
reverb.
This parameter only has an effect when you have
set the Mod On/Off switch to On.

■Reverb parameters
TC Electronic TonePrint Editor ■Manual for software version 1.0 16
Early parameter
Parameter range: -24.5 to 0.0 dB
Use the Early parameter to set the output level of
the “early reflections” part of the reverb algorithm.
■Increase the Early parameter’s value to em-
phasize the definition of the simulated room.
■Decrease the Early parameter’s value to set fo-
cus on the diffuse part of the algorithm. When
Early is set to a low value, the reverb effect will
mainly consist of the reverb “tail”.
Reverb parameter
Parameter range: -24.5 to 0 dB
Use the Reverb parameter to set the Output level
of the diffuse field part of the reverb algorithm.
Decrease the Reverb parameter’s value to em-
phasize the early reflections and thereby the defi-
nition of the simulated room.
Dynamix Mode switch
Parameter settings: Off / Positive / Inverse
Dynamix is a unique feature inherited from the
legendary TC 2290 delay. Dynamix allows you to
control the level of the reverb via the dynamics of
the input signal. This creates a very vivid effect
that interacts with your style of playing and choice
of dynamics.
Using the Dynamix Threshold parameter (see be-
low), you can set a “level limit” for your input that
will help control the reverb level in two different
modes – Positive and Inverse.
Off setting
Disables the Dynamix Mode and gives you a reg-
ular Reverb setting as you know it.
Positive mode
When you set the Dynamix Mode switch to Posi-
tive and the level of the input signal exceeds the
Dynamix Threshold limit, the reverb will be damp-
ened. If the input signal falls below the Dynamix
Threshold limit, the reverb will return.
Inverse mode
When you set the Dynamix Mode switch to In-
verse and the level of the input signal exceeds
the Dynamix Threshold limit, the reverb will be
audible. If the input signal falls below the Dyna-
mix Threshold limit, the reverb will be dampened.
Dynamix Threshold parameter
Parameter range: -50 to 0 dB
This parameter is only applicable when Dynamix
Mode is set to Positive or Inverse.
The Dynamix Threshold acts as a “level limit”.
When the threshold is crossed, the reverb will
either appear or dampen in accordance with the
following parameters: Dynamix Mode, Dynamix
Damp, Dynamix Attack and Dynamix Release.
Dynamix Damp parameter
Parameter range: -60 to 0 dB
This parameter is only applicable when Dynamix
Mode is set to Positive or Inverse.
Use the Dynamix Damp parameter to set the at-
tenuation that will be applied to the reverb when
the input signal rises above (Positive mode) or
falls below (Inverse mode) the Dynamix Thresh-
old setting.
Dynamix Attack parameter
Parameter range: 0 to 1.000 s
This parameter is only applicable when Dynamix
Mode is set to Positive or Inverse.
Use the Dynamix Attack parameter to set the at-
tack time (the build-up phase) of the Reverb En-
velope.
Dynamix Release parameter
Parameter range: 0 to 1.000 s
This parameter is only applicable when Dynamix
Mode is set to Positive or Inverse.
Use the Dynamix Release parameter to set the
release time (the decay) of the Reverb Envelope.
The most gated and unnatural effects are ob-
tained using short Release settings. For a typical
eighties-style sound, Dynamix Release should be
set between 0 and 100 ms.

■Getting support
TC Electronic TonePrint Editor ■Manual for software version 1.0 17
Updating TonePrint
Editor
If you download a newer version of TonePrint
Editor, you can simply replace the previously in-
stalled version.
Getting support
If you still have questions about the product after
reading this manual, please get in touch with TC
Support:
http://www.tcelectronic.com/support/