TE Connectivity 2352906 Series User manual

12-Port GIGABIT MANAGED RACK MNT
PoE SWITCH QUICK INSTALLATION GUIDE
INTRODUCTION
The 2352906 series is a managed 10G/2.5G redundant PoE Ethernet switch with 8x
10/100/1000 Base-T(X) P.S.E. and 4x 1G/2.5G/5G/10GBase-T ports, specifically de-
signed for the toughest environment and fully compliant with EN50155. The switch
supports Ethernet Redundancy protocols such as TE-Ring (recovery time < 30ms over
250 units), TE-Chain, MRP and MSTP (RSTP/STP compatible) which can protect your
mission critical applications from network interruptions or temporary malfunctions.
2352906 also support Power over Ethernet, a system to transmit electrical power up
to 30 watts per port, along with data, to remote devices over standard twisted-pair
cable in an Ethernet network. The series can also be managed centralized and conve-
nient by TE-Vision, Telnet and console (CLI) configuration.
PACKAGE CONTENTS
The device is shipped with the following items. If any of these items is missing or da-
maged, please contact your customer service representative for assistance.
• 2352906 series Ethernet switch
• Rack monting kit (Left + Right)
• CD Containing software
• Quick Installation Guide
PREPARATION
Before you begin installing the device, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based
system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the eect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
DIMENSIONS (in mm)
EN 50155
SWITCH
MAIN FEATURES:
* LEADING EN50155-COMPLIANT ETHERNET SWITCH FOR INDUSTRIAL APPLICATIONS,
SUCH AS ROLLING STOCK, VEHICLE, AND RAILWAY APPLICATIONS.
* SUPPORTS IEEE 802.3AZ COMPLIANT POE WITH MAXIMUM 15.4 WATTS PER PORT.
* PROVIDE 8X10/100/1000BASE-T(X) POE (P.S.E.) PORTS.
* SUPPORT AUTO-NEGOTIATION AND AUTO-MDI/MDI-X.
* SUPPORT STORE, FLOW CONTROL AND FORWARD TRANSMISSION.
* M12 CONNECTORS TO GUARANTEE RELIABLE OPERATION AGAINST ENVIRONMENTAL
DISTURBANCES.
* RIGID IP-30 HOUSING DESIGN AND WALL MOUNTED.

24-Port GIGABIT MANAGED PoE
SWITCH QUICK INSTALLATION GUIDE
INSTALLATION
Rack mounting
Step 1: Install left and right front mounting brackets to the switch using 4 M3 screws
on each sideprovided with switch.
Step 2: With front brackets orientated in front of the rack, nest front and rear bra-
ckets together. Fasten together using remaining M4 screws into counter sunk holes.
Step 3: Fasten the front mounting bracket to the front of the rack.
PANEL LAYOUTS WIRING
For pin assignments please refer to the instructions below:
Grounding
Grounding and wire routing help limit the eects of noise due to electromagnetic in-
terference (EMI). Run the ground connection from the grounding pin on the power
connector to the grounding surface prior to connecting devices.
Power port pinouts
The 2352906 series uses the M12 S-coded 4-pin female connector on the front panel
for the power input.
Step 1: Insert a power cable to the power connector on
the device.
Step 2: Rotate the outer ring of the cable connector until
a snug fit is achieved. Make sure the connection is tight.
Console port pinout
Relay
NC
NC
NC
M12 X-Code Ethernet ports
Relay output ports pinouts
The switch uses the M12 A-coded 5-pin female
connector on the front panel for relay output. Use
a cable with an M12 A-coded 5-pin male connector
to connect the relay. The relay contacts will detect
user-configured events and form an open circuit
when an event is triggered.
The switch has one RS-232 (M12 A-Code 5pin)
console port, located on the front panel. Use a
M12-to-DB9 console cable to connect the conso-
le port to your PC‘s COM port.
Pin
No. Description Pin No. Description
1 BI_DA+/Vout+ 5 BI_DD+
2 BI_DA-/Vout+ 6 BI_DD-
3 BI_DB+/Vout- 7 BI_DC-
4 BI_DB-/Vout- 8 BI_DC+
1
1 Reset Button
2 Power status LED
3 R.M. Status LED
4 Ring Status LED
5 Fault LED
6 Power Connector
7 Relay output port
8 Console port
8
2
3
5
4
9 PoE enabled Gigabit ethernet ports
10 Link/ACT LED for PoE enabled Gigabit ports
11 PoE indicator for PoE enabled Gigabit ports
12 Speed LED for PoE enabled Gigabit ports
13 1G/2.5G/5G/10GBase-T Ethernet ports with bypass
14 Link/ACT LED for non-PoE Gigabit ports
15 LED for 5G/2.5Gbps Ethernet speed indicator
16 LED for 10G/1Gbps Ethernet speed indicator
9
12
10
6
13
11
16
14 15
7

24-Port GIGABIT MANAGED PoE
SWITCH QUICK INSTALLATION GUIDE
LED INDICATORS
After installing the switch and connecting cables, the green power LED should turn on.
Please refer to the following table for LED indication.
LED Color Status Description
PWR Green On DC power module activated
R.M Green On Device operating in Ring master mode
Ring Green On Ring enabled
Blink Ring structure is broken
Fault Amber On Errors occur (i.e. power failure or port malfunction)
10/100/1000Base-T(X) P.S.E. Ethernet ports
LNK/ACT Green On Port is linked
Blink Transmitting data
PoE Green On Power supplied over Ethernet
Speed
Green On Port is running at 1Gbps
Amber On Port is running at 100 Mbps
- O Port is running at 10Mbps
1G/2.5G/5G/10GBase-T Ethernet ports
LNK/ACT Green On Port is linked
Blink Transmitting data
5G/2.5G Amber On Port is running at 2.5Gbps
Green On Port is running at 5Gbps
10G/1G Amber On Port is running at 1Gbps
Green On Port is running at 10Gbps
Revision 1_0, 29 August 2019
NETWORK CONNECTION
The device provides Ethernet ports in M12 connector type. According to the link type,
the switchuses CAT 3, 4, 5,5e UTP cables to connect to any other network devices
(PCs, servers, switches,routers, or hubs). Please refer to the following table for cable
specifications
Pin No. Type Max Length Connector
10BASE-T Cat. 3, 4, 5 100ΩUTP 100m M12 X-Coding Connector
100BASE-T Cat. 5 100ΩUTP UTP 100m M12 X-Coding Connector
1000BASE-T Cat. 5/5e 100ΩUTP UTP 100m M12 X-Coding Connector
Partnumber Input
Power
PoE power
budget
per group
2352906-1 72-110VDC 60W
2352906-2
PoE power budget
LOGIN
Default IP adress: 192.168.10.1
Default username: admin
Default password: admin
Refer to the user manual for further instructions
RESET
To restore the device configurations back to the factory defaults, press the Reset but-
ton for 5 seconds. Once the power indicator starts to flash, release the button. The
device will then reboot and return to factory defaults.