Teac CD-P750 DAB User manual

Z
CD-P750 DAB
CD PLAYER/TUNER
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
GEBRUIKERSHANDLEIDING
BRUKSANVISNING
OPCDP750TEA02
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
NEDERLANDS
SVENSKA

IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
<The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated“dangerous voltage”within the
product’s enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to persons.
BThe exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION
oDO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE
INSIDE.
oIF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR
A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS
BEEN REPAIRED.
oUSE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or ground-
ing-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the man-
ufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
oThe apparatus draws nominal non-operating power from the
AC outlet with its POWER or STANDBY/ON switch not in the ON
position.
oThe mains plug is used as the disconnect device; the discon-
nect device shall remain readily operable.
oCaution should be taken when using earphones or headphones
with the product because excessive sound pressure (volume) from
earphones or headphones can cause hearing loss.
CAUTION
oDo not expose this apparatus to drips or splashes.
oDo not place any objects filled with liquids, such as vases, on
the apparatus.
oDo not install this apparatus in a confined space such as a
book case or similar unit.
oThe apparatus should be located close enough to the AC
outlet so that you can easily reach the power cord plug at
any time.
oIf the product uses batteries (including a battery pack or
installed batteries), they should not be exposed to sunshine,
fire or excessive heat.
oCAUTION for products that use replaceable lithium batteries:
there is danger of explosion if a battery is replaced with an
incorrect type of battery. Replace only with the same or
equivalent type.
WARNING
Products with Class !construction are equipped with a power
supply cord that has a grounding plug. The cord of such a
product must be plugged into an AC outlet that has a protec-
tive grounding connection.
2

EN
VPrecautions concerning batteries
Misuse of batteries could cause them to rupture or leak leading to
fire, injury or the staining of nearby things. Please read and observe
the following precautions carefully.
oBe sure to insert the batteries with correct positive (¥) and
negative (^) orientations.
oUse batteries of the same type. Never use different types of bat-
teries together.
oIf the remote control is not used for a long time (more than a
month), remove the batteries to prevent them from leaking.
oIf the batteries leak, wipe away the leakage inside the battery
compartment and replace the batteries with new ones.
oDo not use batteries of types other than those specified. Do not
mix new batteries with old ones or use different types of batter-
ies together.
oDo not heat or disassemble batteries. Never throw batteries into
fire or water.
oDo not carry or store batteries with other metallic objects. The
batteries could short circuit, leak or explode.
oNever recharge a battery unless it is confirmed to be a recharge-
able type.
oDo not expose batteries to extremely low air pressure as it could
result in an explosion or leakage of flammable liquids or gases.
For European Customers
Disposal of electrical and electronic equipment and
batteries and/or accumulators
a) All electrical/electronic equipment and waste batteries/
accumulators should be disposed of separately from the
municipal waste stream via collection facilities designated
by the government or local authorities.
b) By disposing of electrical/electronic equipment and waste
batteries/accumulators correctly, you will help save valu-
able resources and prevent any potential negative effects
on human health and the environment.
c) Improper disposal of waste electrical/electronic equip-
ment and batteries/accumulators can have serious effects
on the environment and human health because of the
presence of hazardous substances in the equipment.
d) The Waste Electrical and Electronic Equipment
(WEEE) symbols, which show wheeled bins that
have been crossed out, indicate that electrical/
electronic equipment and batteries/accumulators
must be collected and disposed of separately from
household waste.
If a battery or accumulator contains more than the
specified values of lead (Pb), mercury (Hg), and/or
cadmium (Cd) as defined in the Battery Directive
(2006/66/EC, 2013/56/EU), then the chemical sym-
bols for those elements will be indicated beneath the
WEEE symbol.
e) Return and collection systems are available to end users.
For more detailed information about the disposal of old
electrical/electronic equipment and waste batteries/accu-
mulators, please contact your city office, waste disposal
service or the shop where you purchased the equipment.
Pb
, Hg,
Cd
Compliance of radio transmitter and
interference
This product has the function of broadband transmitter using
2.4GHz Band.
Use frequency range: 2402MHz – 2480MHz
Maximum output power: Bluetooth® Class 1 (less than 10mW)
Please use only in the country where you purchased the product.
Depending on the country, restrictions on the use of Bluetooth
wireless technology might exist.
Model for EEA (European Economic Area)
Hereby, TEAC Corporation declares that the radio
equipment type is in compliance with Directive
2014/53/EU., and the other Directives, and
Commission Regulations.
Model for UK
Hereby, TEAC CORPORATION declares that the
radio equipment type is in compliance with UK
Radio Equipment Regulations.
The full text of the EU or UK declaration of conformity is available at
the following internet address. Please contact us by e-mail.
https://teacsupport.aqipa.com/
Radiation Exposure requirements
This equipment meets the regulation, which is recognized interna-
tionally, for the case of human exposure to radio waves generated
by the transmitter.
Statement of compliance
Model for EEA and UK
This equipment complies with EN.62479; Assessment of electronic
and electrical equipment related to human exposure restrictions
for electromagnetic fields.
3

IMPORTANT SAFETY INSTRUCTIONS (continued)
Laser information
This product contains a semiconductor laser system inside the cab-
inet and is classified as a“CLASS 1 LASER PRODUCT”.
To prevent being exposed to the laser beam, do not try to open
the enclosure.
Optical pickup
Type: EP-C250L
Manufacturer: GUANGDONG EVER BRIGHT GROUP CO.,LTD
Laser output: Less than 0.30 mW on the objective lens
Wavelength: 792 +8 nm/−12 nm
The SDHC logo is a trademark of SD-3C, LLC.
The Bluetooth® word mark and logo are the property of Bluetooth
SIG, Inc. and are used by TEAC Corporation with permission.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/
or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered
in the United States and other countries. aptX is a trademark
of Qualcomm Technologies International, Ltd., registered in the
United States and other countries.
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson Licensing.
Supply of this product does not convey a license nor imply any
right to distribute MPEG Layer-3 compliant content created with
this product in revenue-generating broadcast systems (terrestrial,
satellite, cable and/or other distribution channels), streaming
applications (via Internet, intranets and/or other networks), other
content distribution systems (pay-audio or audio-on-demand
applications and the like) or on physical media (compact discs, dig-
ital versatile discs, semiconductor chips, hard drives, memory cards
and the like). An independent license for such use is required. For
details, please visit http://mp3licensing.com.
Other company names, product names and logos in this doc-
ument are the trademarks or registered trademarks of their
respective owners.
Information is given about products in this manual only
for the purpose of example and does not indicate any
guarantees against infringements of third-party intel-
lectual property rights and other rights related to them.
TEAC Corporation will bear no responsibility for infringe-
ments on third-party intellectual property rights or their
occurrence because of the use of these products.
With the exception of personal enjoyment and similar
uses, copyrighted materials belonging to third parties
cannot be used without permission from the rights hold-
ers in accordance with copyright law. Please use the
equipment appropriately.
TEAC Corporation will bear no responsibility for rights
infringements committed by users of this product.
4

EN
Contents
IMPORTANT SAFETY INSTRUCTIONS ..............................2
1 – Introduction ..................................................6
Features.......................................................6
Included accessories ..........................................6
Conventions used in this manual ..............................6
Using the TEAC International Site ..............................6
Precautions for placement and use ............................7
Notes about power supplies...................................7
Beware of condensation.......................................7
Cleaning the unit..............................................7
About compact discs..........................................7
Precautions for use .........................................7
Slot loading of discs ...........................................8
SD cards and USB flash drives..................................8
Precautions for use .........................................8
SD card write protection ...................................8
Bluetooth® notes ..............................................8
Profiles .....................................................8
Codecs.....................................................8
Content protection.........................................8
Transmission security.......................................8
2 – Names and Functions of Parts .................................9
Front panel....................................................9
Rear panel....................................................12
Wireless remote control (RC-1336) ............................13
Home Screen.................................................14
Menu structure...............................................15
Basic Menu screen operations ................................15
Menu operation procedures...............................15
3 – Preparation ..................................................16
Making connections..........................................16
Preparing the remote control.................................17
Installing batteries.........................................17
When to replace batteries .................................17
Battery precautions .......................................17
Using the wireless remote control .........................17
Turning the unit on and off ...................................17
Adjusting the display brightness..............................17
Inserting and removing discs .................................18
Inserting discs.............................................18
Ejecting discs .............................................18
Forcing disc ejection ......................................18
Inserting and removing SD cards .............................18
Inserting SD cards.........................................18
Removing SD cards .......................................18
SD card write protection switches .........................18
Connecting and disconnecting USB flash drives ..............19
Connecting USB flash drives...............................19
Disconnecting USB flash drives ............................19
Selecting the playback source ................................19
4 – CD/SD/USB playback ........................................20
Files that can be played back .................................20
Tracks and folders on SD cards and USB flash drives...........20
Playback area.................................................21
Setting the playback area..................................21
Basic playback operations ....................................21
Playing tracks .............................................21
Selecting tracks for playback..................................21
Skipping to earlier and later tracks .........................21
Selecting tracks directly ...................................22
Folder playback (SD cards and USB flash drives only) ..........22
Playback modes ..............................................24
Setting the playback mode................................24
Searching backward and forward.............................24
Using the repeat playback function...........................25
Ordinary repeat playback settings .........................25
A-B repeat playback settings (audio CDs only) .............25
Program playback (audio CDs only) ...........................26
Preparing the program ....................................26
Checking and editing the program ........................26
Removing steps from the program ........................27
Adding steps to the program..............................27
Clearing the program .....................................27
Using the power-on-play function............................28
Using the resume function ...................................28
Time and text information display ............................29
5 – Bluetooth device playback ...................................30
Pairing .......................................................30
Usable controls...............................................30
Playback from a Bluetooth device. ............................30
Unpairing ....................................................30
6 – Using DAB tuner .............................................31
Setting up your DAB tuner....................................31
Listening to DAB Radio .......................................31
Setting the DAB display.......................................31
Using the DAB menu .........................................31
Broadcast station presets .....................................32
Setting radio station presets manually .....................32
Selecting presets..........................................32
Clearing preset assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7 – Listening to FM radio.........................................33
Tuning in radio stations.......................................33
Changing the received frequency .........................33
Setting the FM mode......................................33
Setting radio station presets ..................................33
Setting radio station presets automatically.................33
Setting radio station presets manually .....................33
Selecting preset stations ..................................34
Clearing preset assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Setting the tuner broadcast outputs ..........................34
RDS (Radio Data System) .....................................34
PTY search ................................................34
RDS Program type.........................................35
8 – Dubbing (copying) functions.................................36
Dubbing overview ...........................................36
Dubbing procedures .........................................36
Muting analog outputs while dubbing .......................37
Make dubbing format settings................................37
Recording times when dubbing ..............................37
9 – Other functions ..............................................38
Setting the automatic power saving function .................38
Adjusting the analog output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Using the AUX IN jack ........................................38
Checking the firmware version ...............................38
Restoring factory default settings.............................38
10 – Troubleshooting ............................................39
11 – Specifications...............................................40
Ratings.......................................................40
Inputs and outputs ...........................................40
Analog audio input and output ratings ....................40
DIGITAL OUT connectors ..................................40
Audio performance ..........................................40
Bluetooth function ...........................................40
Tuner.........................................................41
Other ........................................................41
Dimensional drawings........................................41
5

Thank you very much for choosing TEAC.
Read this manual carefully to get the best performance from this
unit. After reading it, keep it in a safe place for future reference.
Features
oPlayback of CDs, SD cards and USB flash drives possible
oCD player supports CD-DA, CD-ROM, CD-R, CD-RW (CD-DA for-
mat only), MP3-CD and WMA-CD formats
oMP3, AAC, WAV and WMA files can be played from SD cards and
USB flash drives
oBluetooth® receiver built-in, enabling playback from smart
phones and other devices
oDAB/FM tuner built-in
oAUX IN jack can be used for playback from mobile audio players
and other devices
oAnalog outputs include a pair of RCA unbalanced jacks
oRecording from audio CDs and the tuner to SD cards and USB
flash drives is possible
oUnbalanced RCA connectors dedicated for tuner output
oCD/SD/USB direct track searching using number keys or the
dedicated remote control
oPower-on-play function can automatically start track playback
when the unit is turned on
oHeadphone output jack enables audio monitoring
oUp to 32 tracks can be added to the program memory
Included accessories
Check to be sure the box contains all the included items shown
below. Please contact the store where you purchased this unit
if any of these items are missing or have been damaged during
transportation.
Power cord × 1
Wireless remote control (RC-1336) × 1
Batteries for remote control (AAA) × 2
FM antenna × 1
RCA cable × 1
Owner’s Manual (this document) × 1
oSee page282 for warranty information.
Conventions used in this manual
In this manual, we use the following conventions:
oWhen we refer to buttons, connectors and other parts of this
unit and other equipment, we use a bold font like this: HOME/
MENU button.
oWhen we show characters that appear on the display, the type-
face looks like this: Menu.
oSD/SDHC memory cards are called“SD cards”.
oThe CD-DA format is sometimes called the “audio CD” format. In
addition, CDs with tracks recorded in the audio CD format are
sometimes called“audio CDs”.
oCDs with MP3 and WMA files are called“data CDs”.
oThe input source that is currently selected is called the “current
source”.
oThe folder that is currently selected is called the“current folder”.
oComputers, portable audio devices and other equipment con-
nected to this unit using Bluetooth wireless transmission are
called“Bluetooth devices”.
oAs necessary, additional information is provided under TIP, NOTE
and ATTENTION headings.
TIP
These are tips about how to use the unit.
NOTE
These provide additional explanations and describe special
cases.
ATTENTION
Failure to follow these instructions could result in injury, dam-
age to equipment or lost recording data, for example.
Using the TEAC International Site
You can download updates for this unit from the TEAC
International Site:
https://teac.jp/int/
Click Language at the top right of the page and select the desired
country or region to access a page in the corresponding language.
1 – Introduction
6

EN
Precautions for placement and use
oThe operating temperature range of this unit is 5–35°C.
oDo not install this unit in the following types of locations. Doing
so could make the sound quality worse or cause malfunction.
oLocations with frequent vibrations
oNear windows or other places exposed to direct sunlight
oNear heaters or other extremely hot places
oExtremely cold places
oVery humid or poorly ventilated places
oVery dusty places
oInstall the unit so that it is level.
oTo enable good heat dissipation, do not place anything on top
of the unit.
oDo not place the unit on top of a power amplifier or other
device that generates heat.
oIn order to enable good heat dissipation, leave at least 20cm
(8”) between this unit and walls and other equipment when
installing it. If you put it in a rack, for example, leave at least
5cm (2”) open above and 10cm (4”) open behind it.
Failure to provide these gaps could cause heat to build up
inside and result in fire.
Notes about power supplies
oInsert the included power cord all the way into the AC IN
connector.
oDo not connect a power supply other than one that is AC 100V
 240V (50/60Hz).
oHold the power cord by its plug when connecting or discon-
necting it.
Beware of condensation
Condensation could occur if the unit is moved from a cold place
to a warm place, it is used immediately after a cold room has been
heated or it is otherwise exposed to a sudden temperature change.
To prevent this, or if this occurs, let the unit sit for one or two hours
at the new room temperature before using it.
Cleaning the unit
Use a dry soft cloth to wipe the unit clean. Do not wipe with
chemical cleaning cloths, thinner, alcohol or other chemical agents.
Doing so could damage the surface or cause discoloration.
About compact discs
In addition to commercially-available music CDs, this unit can play
CD-R and CD-RW discs recorded in the audio CD (CD-DA) format as
well as CD-R and CD-RW discs that contain MP3 audio files.
ATTENTION
8cm CDs cannot be used. If an 8cm CD is inserted, it will auto-
matically be ejected. During ejection, if it stops at a place where
it cannot be removed, press and hold the EJECT (-)button.
Precautions for use
oAlways insert discs with the label facing upward.
oTo remove a disc from its case, press down on the center of
the disc holder, then lift the disc out, holding it carefully by the
edges.
oDo not touch the signal side (the unlabeled side). Fingerprints,
oils and other substances can cause errors during playback.
oIf fingerprints or dust adhere to the signal recording side of a
disc, wipe gently with a soft dry cloth from the center towards
the outside edge.
oDirt on discs can lower the sound quality, so clean them and
always store them in a clean state.
oDo not use any record spray, anti-static solutions, benzene,
paint thinner or other chemical agents to clean CDs as they
could damage the delicate playing surface. It may cause CDs to
become unplayable.
oDo not apply labels or other materials to discs. Do not use discs
that have had tape, stickers or other materials applied to their
surface. Do not use discs that have sticky residue from stickers,
etc. Such discs could become stuck in the unit or cause it to
malfunction.
oNever use a commercially available CD stabilizer.
oUsing stabilizers with this player will damage the mechanism
and cause it to malfunction.
oDo not use cracked discs.
oOnly use circular compact discs. Avoid using non-circular pro-
motional, etc. discs.
oCopy Control CDs have been sold by several record companies
in an attempt to protect their copyrights. Since some of these
discs do not comply with the CD specifications, they may not
be playable on the unit.
7

Slot loading of discs
1. As shown in the illustration, hold the disc with the labeled side
up and insert it part way into the slot.
2. Push the disc in further until just before it disappears. It will
automatically be drawn in to the slot.
If a disc will not load properly
If a disc becomes stuck during insertion, for example, and is
difficult to push, do not try to force the disc in. Pull the disc out
once, press the EJECT (-)button, and then try inserting it again.
(Trying to force the disc in could damage the unit.)
SD cards and USB flash drives
This unit uses SD cards and USB flash drives for recording and
playback.
Precautions for use
SD cards and USB flash drives are delicate media.
In order to avoid damaging SD cards and USB flash drives, please
take the following precautions when handling them.
oDo not leave them in extremely hot or cold places.
oDo not leave them in extremely humid places.
oDo not let them get wet.
oDo not put things on top of them or twist them.
oDo not hit them.
oDo not remove or insert them during recording, playback, data
transmission or other access.
oWhen transporting them, put them into cases, for example.
SD card write protection
This unit writes track information to the media in order to improve
operation performance. Since track information cannot be written
to SD cards that are write-protected, the amount of time needed
to read media will become longer, for example.
Bluetooth® notes
This unit has a built-in Bluetooth audio receiver, and can output
sound played on a computer or portable audio device that sup-
ports Bluetooth wireless transmission (Bluetooth device).
ATTENTION
The Bluetooth function of this unit is not guaranteed to enable
connection or operation with all Bluetooth devices.
Profiles
This unit supports the following Bluetooth profiles.
oA2DP (Advanced Audio Distribution Profile)
oAVRCP (Audio/Video Remote Control Profile)
In order to transfer audio by Bluetooth wireless technology, the
Bluetooth device must support A2DP.
In order to control playback on the Bluetooth device, it must sup-
port AVRCP.
Even if a Bluetooth device supports the same profiles, though, its
functions might differ according to its specifications.
Codecs
This unit supports the following codecs. It will automatically select
one of them during audio transfer.
oSBC
oAAC
oQualcomm® aptX™ audio
oQualcomm® aptX™ HD audio
The unit will select the appropriate codec to use according to the
codec compatibility of the other Bluetooth device and communi-
cation conditions.
NOTE
i You cannot select the codec to be used by pressing a button,
for example.
i Due to characteristics of Bluetooth wireless technology, play-
back from a Bluetooth device will be slightly delayed compared
to playback from this unit.
Content protection
This unit supports SCMS-T as a form of content protection when
transmitting audio, so it can play protected audio.
Transmission security
This unit supports security functions during Bluetooth transmission
in accordance with the Bluetooth standard specifications, but it
does not guarantee the privacy of such transmissions.
TEAC CORPORATION will bear no responsibility should an informa-
tion leak occur during Bluetooth wireless transmission.
1 – Introduction (continued)
8

EN
Front panel
POWER switch
This turns the unit on and off
CAUTION
Before turning the unit on, lower the volumes of connected
equipment to their minimum levels.
Failure to do so could result in a sudden loud noise that could
harm hearing, for example.
NOTE
Do not turn off the power when the unit is operating (including
dubbing, playing back, or writing data to an SD card or USB
flash drive). Doing so could cause dubbing to fail or dubbed
data to be lost, for example.
Disc slot
Insert a disc here.
After a disc is inserted partway, the unit will automatically draw
it in.
EJECT (-) button
Press to eject a disc. (see “Inserting and removing discs” on
page18)
Press and hold for at least 10 seconds to force-eject a disc. (see
“Forcing disc ejection”on page18)
Display
This shows various types of information.
HOME/MENU button
i When the Home Screen is open, press to open the Menu
screen. (see “Menu structure” on page15) (see “Basic Menu
screen operations”on page15)
i When the Menu screen is open, press this button to return to
the Home Screen.
MULTI JOG dial
This dial functions as a dial when turned and as a button when
pressed.
Dial functions
i When the current source is CD, USB or SD and the playback
area is set to “All”, turn the MULTI JOG dial to skip tracks. (see
“Skipping to earlier and later tracks”on page21)
i When the current source is USB or SD and the playback area
is folder ( icon shown), turn the MULTI JOG dial to move
among tracks and folders. (see“Folder playback (SD cards and
USB flash drives only)”on page22)
i When the current source is FM, turn the MULTI JOG dial to
change the received frequency. (see “Tuning in radio stations”
on page33)
i When the input source is DAB, turn the MULTI JOG dial to start
automatic station selection. (see “Listening to DAB Radio” on
page31)
i When the current source is DAB/FM and preset mode is
enabled, turn the MULTI JOG dial to move to the previous or
next preset number. (see“Setting radio station presets”on page
33 and“Broadcast station presets”on page32)
i When a Menu screen is open, turn to select items and change
setting values. (see “Basic Menu screen operations” on
page15)
i When pressing and holding SHIFT button, turn the MULTI
JOG dial to adjust the display brightness. (see “Adjusting the
display brightness”on page17)
Button function
i When a Menu Screen is open, press to confirm selections and
settings (ENTER button function).
STOP (8) button
i Press to stop playback.
i When the current source is DAB or FM, press to switch
between frequency and preset modes. (see “Changing the
received frequency”on page33)
i Press when dubbing to stop. (see “Dubbing procedures” on
page36)
PLAY (7) button
Press when stopped or in playback standby to start playback.
PAUSE (9) button
Press when stopped or playing back to start playback standby.
m/,[FAST] buttons
i Press and hold these buttons to search backward/forward.
(see“Searching backward and forward”on page24)
i If the current source is CD, USB or SD and you are searching
backward/forward, press and hold the button for the oppo-
site direction (mor ,) to search at high-speed. (see
“Searching backward and forward”on page24)
i When the current source is FM, press to automatically search
received frequencies for that frequency mode. (see“Changing
the received frequency”on page33)
i When the input source is DAB, press to start automatic station
selection.
2 – Names and Functions of Parts
9

PHONES jack/knob
Use this standard stereo jack to connect stereo headphones.
Use an adapter to connect headphones with a mini plug.
Use the PHONES knob to adjust the headphone output level.
PHONES jack output can be lowered up to −18dB in 1dB inter-
vals using the A.Out Att. setting screen. (see “Adjusting the
analog output” on page38)
CAUTION
Before connecting headphones, minimize the volume with the
PHONES knob. Failure to do so could result in a sudden loud
noise that could harm hearing, for example.
AUX IN jack
This stereo mini jack is an audio line input jack.
Connect a portable digital player or other external audio device
here. (see“Using the AUX IN jack” on page38)
CAUTION
i Before connecting another device to the AUX IN jack, minimize
the volume of that device. Failure to do so could result in a sud-
den loud noise that could harm hearing, for example.
i Before connecting or disconnecting with the AUX IN jack,
set the current source to something other than AUX (CD or
Bluetooth) or turn the unit off.
Remote control signal receiver
Signals from the wireless remote control (RC-1336) are received
here. When operating the remote control, point it toward this
receiver.
1 [PROGRAM] button
i Press to input track number 1when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD and shift mode is active
(SHIFT indicator lit), press this to start program setting mode.
Press this to check and edit the program after it has been pre-
pared. (see“Preparing the program”on page26)
NOTE
i The number buttons on the unit (1 [PROGRAM] – 0 [DUB])
can be used to specify numbers for track selection. For track
numbers, a maximum of two digits can be input for audio CDs
and three digits for data CDs. (see “Selecting tracks directly” on
page22)
i When in shift mode (SHIFT indicator lit), pressing a number
button will change the setting of the function shown in white
lettering below the button.
2 [P.O.PLAY] button
i Press to input track number 2when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When in shift mode (SHIFT indicator lit), press to turn the
power-on-play function on/off. (see“Using the power-on-play
function”on page28)
3 [RANDOM] button
i Press to input track number 3when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD, USB or SD, and shift mode is
active (SHIFT indicator lit), press to switch between ordi-
nary and random playback modes. (see “Playback modes” on
page24)
4 [REPEAT] button
i Press to input track number 4when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD, USB or SD, and shift mode
is active (SHIFT indicator lit), press to cycle through repeat
playback modes (ordinary playback, single repeat and all
repeat playback modes). (see “Ordinary repeat playback set-
tings”on page25)
5 [A-B REP] button
i Press to input track number 5when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is CD and shift mode is active
(SHIFT indicator lit), press to set the A-B repeat function
starting (A) and ending (B) points. (see “A-B repeat playback
settings (audio CDs only)”on page25)
6 [A. PRESET] button
i Press to input track number 6when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is DAB or FM and shift mode is active
(SHIFT indicator lit), press to automatically program the pre-
set stations. (see “Setting radio station presets automatically”
on page33)
7 [M.PRESET] button
i Press to input track number 7when the current source is CD,
USB or SD and the playback area is set to “All”. (see “Selecting
tracks directly”on page22)
i When the current source is DAB or FM, press to tune in a pre-
set station.
i When the current source is DAB or FM and shift mode is active
(SHIFT indicator lit), press to manually program the preset
stations. (see “Setting radio station presets manually” on
page33)
2 – Names and Functions of Parts (continued)
10