Teac BLUANCM2B User manual

BLUANCM2B
Active Noise Cancelling Bluetooth
Headphones
User Guide
Product Specifications
BLUANCM2B
Bluetooth Version V4.1 CSR8635 Talking Time 50H
Speaker 3 Ω 40mm
0- 0KHZ Music Playing Time 50H

Standby Time 90 DAYS ANC Music Playing Time 6H
Frequency .4hz- .48Khz Charge Current 1A
Microphone Sensitivity:-38 ±3dB
Frequency:30-16 KHZ Charge Voltage 5V
ANC Function Yes Charging Time -3H
Protocol Supported HSP HFP
A DP AVRCP Bluetooth Distance 10m
Battery Capacity 1050 mAh
Functions
Keys Function：
NO
.Name Introduction
1Volume+/Next Track Press once to increase volume. Press and hold to skip to the next track.
Play/Pause
Power On/Off/Battery indicator: Press and hold 3s to power on, press and hold
3s to power off. (Once power on, pairing mode is entered automatically after 5s)
Phone Call Control: Press to answer/hang up. Press and hold to refuse. Double
click to start voice assistance e.g. Siri.

3Volume -/Skip Backward Press to volume down/press and hold to play previous track.
4 3.5mm Earphone Jack While extra earphone plugged, Bluetooth turns off automatically, and battery,
controls, ANC, microphone don’t work.
5Microphone Microphone for calling
6ANC button Press to turn on/off Active Noise Cancellation Function
7 Micro-USB
When charging with the Micro-USB cable attached, a red light will be lit to
indicate that it is charging, when fully charged, the light will be lit blue.
Suggestion: Do not use the headphones when charging.
Bluetooth Connection
1. To set the headphones to pairing mode, press and hold the play/pause button for seconds until it powers on,
continue holding for another 3 seconds and it will enter the pairing mode. This will be shown on the LED indicator
which will alternate flashing between blue and red.
(Headphones will power off after 5 minutes if Bluetooth connection is not detected)
. Activate Bluetooth on your phone (or other devices) and set it to search for new devices.
iOS Settings > Bluetooth > On
Android Settings > Bluetooth: On > Scan for devices
3. Select “BLUANCM2B”
If necessary, enter four zeros (0000) for pass code and accept connection.
Once successfully paired, the headphones LED indicator should be flashing blue.
• Two Phones/Devices Connection: Your headphones can pair with two devices simultaneously.
After connecting to Phone/Device A, turn off the headphones and Bluetooth connection on Phone/Device A.
Then restart the headphones and pair it with Phone/Device B while maintaining the connection with Phone/Device
B.
Finally, open up the Bluetooth settings again on Phone/Device A and select “BLUANCM2B” in the menu.
Note: The headphones will play music only from one device even if two devices are successfully connected at the
same time.
• Wired connection：Use the included audio cable to connect. (Bluetooth turns off automatically. Battery, buttons,
ANC and microphone will stop functioning when in AUX mode)
Active Noise Cancellation

Press the ANC button once to activate it. The LED indicator should turn green.
Press once more to turn off ANC.
Charging
Insert the provided micro-USB cable into headphone charging port and connect the other side to a USB wall
charging adapter or a device with USB power out such as a computer USB port.
LED indicator should be lit red while charging.
It is fully charged when the LED indicator is lit blue.
(The headphones will remind you that the battery is low every 15 minutes when the battery power is under 10%)
roubleshooting
Problem Solution
1. The indicator blinks red repeatedly
(interval S) or continuously?
This indicates that the battery is low. Please charge the
headphones as soon as possible.
. Will not turn on? It is possible that it is out of battery.
3. No indicator when charging?
There may be no charge indication for the first few minutes
if the battery is completely exhausted, or it is charged
for the first time after not being used for a long period of time.
The indicator should be lit red to indicate the charging state
after a while.
4. Bluetooth is connected but
is without any sound?
Make sure Bluetooth headphone is turned on.①
Make sure the music sound output is ②
the Bluetooth headphone (BLUANCM2B)
Make sure the Bluetooth headphones and the phone/device are③
paired and connected successfully.
Make sure the distance between Bluetooth headphones④
and phone/device is not more than 10 meters away.
Make sure your phone is within the range of signal and⑤
without any external interference.
Make sure your phone/device is not connected to other devices.⑥
5. There is no sound Make sure you insert the correct 3.5mm audio cable and①

in the headphone when in wired
connection?
connect it properly. Note that the headphone buttons
and microphone will not work when in wired mode.
Make sure phone/device is in normal working condition②
and not damaged.
6. Bluetooth
connection is
not successful?
Make sure the phone/device Bluetooth settings are turned on.①
Make sure the headphone enters Bluetooth pairing②
mode (the LED indicator should be blinking blue)
Ensure that previously connected Bluetooth devices are③
disconnected from the phone/device. Try another attempt at
searching for the device again.
Product Maintenance
Please do not use non-original accessories, as it may cause
performance degradation, physical damages, electrical short
circuits and this will void your warranty.
Please do not disassemble the device on your own as it may
cause physical damage and this will void your warranty.
Please do not place the headphone in a dusty environment.
Please do not allow children under 3 years to play with the headphones.
Please do not place the product in environments with extreme temperatures
as it may cease to function temporarily and/or cause permanent damage to the headphones
and/or its battery life.
Please clean your headphones with a clean, soft and dry cloth.
Please store your headphones in the original package or
keep it in a safe location when not in use.
Battery Maintenance
Please go to a qualified repair center if you need to remove or replace the battery.
(Rechargeable batteries should last for a long time if used properly)

The charging temperature of the rechargeable battery is rated from 10°C to 45°C
Please charge it at least once a month to maintain the battery life
Battery usage time and standby time are affected by usage conditions.
Usage time and standby time provided are only for your reference.
Notes regarding ANC technology
Active Noise Cancelling Technology is more effective in reducing the noise of a busy space and low frequency
noises (150-450Hz) such as the sound of an engine in a car, aeroplane or other vehicles.
Human voice (high frequency waves) cannot be entirely eliminated with ANC.
ERMS AND CONDI IONS
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
1. TEAC warrants that this product is free from defects in material and workmanship under normal domestic use
with reasonable care and skill. Maintenance and cleaning (i.e. laser head) is not covered by this warranty. The
TEAC warranty only applies to TEAC products purchased NEW from a TEAC Authorised Retailer in Australia. This
warranty only applies to the original purchaser and cannot be transferred.
. The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer
under a law in relation to goods or services to which the warranty relates, being the Australian Consumer Law.
3. Refund or replacement via your TEAC Authorised Retailer is available for a period of 14 days after purchase for

goods that have been inspected and determined to have a major failure. Refund and exchange is not applicable for
change of mind.
4. Subject to the terms herein, this warranty effectively covers TEAC products under the 1 Month Replacement
Warranty Scheme, 1 months from the date of original purchase.
5. The warranty is void and warranty claims may be refused, subject to the Australian Consumer Law, if:
a) The product was not transported, installed, operated or maintained according to manufacturer instruction, or b)
The product was abused, damaged, tampered, altered or repaired by any unauthorised persons, or c) Product
failure is due to accidents during use, installation or transit, power surges, use of defective or incompatible external
devices, exposure to abnormal conditions such as excessive temperatures or humidity, or entry of liquids, objects or
creatures into the product, cockroach infestations, or d) The customer is unable to provide proof of purchase of the
product for verification, or e) The serial number of the product is missing or has been tampered with.
6. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with
the sale of any equipment other than as stated in this warranty and outlined above.
7. TEAC and/or its Authorised Service Centres reserve the right to inspect and verify whether the product is
exhibiting a major failure as claimed by customers/retailers.