Technaxx TX-59 User manual

Technaxx
®
Wireless Video Door Phone TX-59
Table of Contents
Introduction
Safety Warning & Attentions
Product Overview
Product Diagram
Installation Guide
Installation Steps & Battery Installation
Attentions during Installation
Installation of Storage Card
Storage Card Introduction
Features
Outdoor Unit Starting Up
Indoor Monitor Starting Up
Outdoor Unit CALL Indoor Monitor
Indoor Monitor View the Camera
Indoor Monitor CALL Indoor Monitor (Intercom)
Night-Vision
Bright / Colour / Volume Adjustment
Tamper Alarm Function
USB Function Description
Indoor Monitor Menus
Battery & Charge
Accessories
Statement
General faults and solutions
Important Hint regarding the User Manuals:
All languages of the user manual are on the CD enclosed. The english
and german version of the user manual is also as printed version
enclosed.
Introduction
This device complies with the requirements of the standards referred to the
Directive R&TTE 1999/5/EC. The Declaration of Conformity you find here:
www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”).
Before using the device the first time, read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks). Free Email:
[e-mail]
If you drill a hole in the wall, please make sure that power cables, electrical cords
and/or pipelines are not damaged. When using the supplied mounting material,
we do not take the liability for a professional installation. You are entirely
responsible to ensure that the mounting material is suitable for the particular
masonry, and that the installation is done properly. When working at higher
altitudes, there is danger of falling! Therefore, use suitable safeguards.
Safety Warning & Attentions
● Do not place the device on an uneven or unstable table-board to prevent
failure or damage caused by falling.
● Only the battery and charger designated by the Company can be used on
the device. Application of other products may lead to leakage, overheating,
blowout and fire of the battery.
● Do not violently strike, shake or toss the device to prevent failure and fire
caused to the wireless video door phone.
● Do not place the device, battery or charger near or in fire or in a place with
flammable and explosive gas; otherwise, damage and fire of electrical circuit
and other accidents may be caused.
● Do not place the device in a place with high temperature, high humidity or
large amount of dust; otherwise, product failure may be caused.
● Keep the device away from children.

Attentions for operation of this product
● Do not apply force on LCD screen or knock other objects with it, otherwise,
breakage and damage of LCD panel and seepage of crystalline liquid will be
caused. If the crystalline liquid enters your eyes, there will be danger of
ablepsia. Wash your eyes (be sure not to rub your eyes) and go to see a
doctor immediately
● Do not dismantle or remodel this product, otherwise, damage, creep age
and electrical fault may be caused to this product.
● Do not press the keys with a pin, stump of pen/pencil and other keen-edged
objects; otherwise, damage or disoperation will be caused.
● Place tiny metal objects such as drawing pin at a place far away from the
speaker. As the speaker has magnetic property while working, it will attract
these tiny metal objects, which may lead to personal injuries or damage of
the speaker.
● Do not project the lens at strong light source, such as the sun; otherwise,
damage of the image sensor may be caused.
● Do not press the terminal of lens with much force; otherwise, personal injury
or damage of the device may be caused.
Attentions for operation of charger
● You may charge the device with a charger or through a USB data line
connected to the computer.
● Charge with matched alternate current; creep age, fire and damage of the
door phone and charger may be caused if other voltage is used.
● It is forbidden to short circuit the charger, otherwise, electrical shock, smoke
and damage of the charger will be caused.
● Do not use the charger at the time when the power cord is damaged,
otherwise, fire and electrical shock will be caused.
● Clear away the dust accumulated on power outlet ASAP.
● Do not place a vessel used to retain water beside the charger to prevent
overheating, creep age and failure of charger caused by spilling water.
● If the charger is in contact with water or other liquids, disconnect the power
supply immediately to prevent overheating, fire, electrical shock and failure
of the charger.
● Do not dismantle or remodel the charger, otherwise, personal injury, electric
shock, fire and damage of charger may be caused.
● Do not use the charger in places with high humidity such as bathroom,
otherwise, electric shock, fire and damage of the charger will be caused.
● Do not touch the charger, electrical line and power outlet with wet hand(s),
otherwise, electric shock may be caused.
● Do not place heavy objects on the electrical line or refit the electrical line,
otherwise, electric shock and fire will be caused.
● Before cleaning and maintenance, first pull the plug off the power outlet.
● Grasp the charger while pulling off the plug, as pulling the electrical line will
lead to damage of electrical line, electric shock and fire.
Operation and maintenance
● Please keep this product dry, as rainwater, moisture, humidity and liquids or
moisture content may contain mineral matters that erode the circuit.
● Do not keep this product in any place with high temperature. As high
temperature may shorten the lifespan of electronic device, damage the
battery and cause deformation or melting of certain plastic parts and
components.
● Do not keep this product in any place with low temperature. As when being
moved from a place with low temperature to a place with normal
temperature, it may generate humidity inside, which may cause damage of
circuit board.
● Do not attempt to dismantle this product. As improper handling by
nonprofessional personnel may cause damage of the device.
● Do not toss, knock or shake this product, as tough operation mode may
damage the motherboard inside the device.
● If this product is made wet by mistake, shut it down, remove the battery, and
restart the product after confirming it complete dry after 24 hours.

● Do not have the metal parts (specially configured interfaces of charger and
data line excluded) in contact with charger interface to avoid short circuit.
● Use clean and dry soft cloth to clean the lens, infrared lamp and light sensor.
！Warning: Improper operation will void warranty!！
Product Overview
Features
1. Fashion appearance: European design, full of modern science and
technology feeling, suitable for houses of various decorative styles.
2. Hidden antenna: built-in antenna design, protect the antenna effectively.
3. Extra large range of vision: 120°wide viewing angle
4. High-resolution color LCD screen: 7” mainstream TFT digital LCD screen,
achieve outstanding clarity.
5. High-resolution digital camera: 300000 pixels digital camera, image focusing
vivid and clear.
6. Infrared Night-Vision: under the environment of insufficient outdoor light, the
indoor monitor can activate the infrared Night-Vision to clearly display and
record the outdoor scenes.
7. Auto detection: it would auto take photo when a visitor come close to the
door.
8. One-key display: simple and convenient to use, view the outdoor scenes and
take photos or record videos under manual or automatically mode just by
pressing down one key.
9. Intercom function: can choose one-way or both-way talkback function.
10. Photo and video is stored on an extended MicroSD memory card up to 4GB.
11. Charge-and-record supported: without the need to worry that the operation
will be affected due to depletion of electrical quantity.
12. Auto circulating memory: without the need to worry that real-time recording is
unachievable due to insufficient space of storage card.
13. USB data charging wire: charge; downloading or uploading audio-visual
materials can be realized through the USB interface.
14. Multifunction holder: wall-hung type or table type provided.
15. Multi machine extended function: support two outdoor units and three indoor
monitor at most.
16. Long distance transmission: communication distance can reach 300 meters
in open space.
17. Frequency range: 2.4G ISM digital public frequency range:2402~2483.5MHz
18. Adaptive frequency hopping technique: AFH (Adaptive Frequency Hopping
Technique), produce communication frequency and Auto-Sync frequency
randomly.

Technical specifications
Power Specific lithium battery 3400mAh
Consumption 400mA
Outline dimension 134 x 74 x 31 mm
Weight 138 g
Environmental temperature –10°C ~ +50°C
Waterproof grade IP55
Placement Hang on out wall
Surface material ABS & hardware accessories
Camera 300000 pixels
View angle 120° wide angle
Night vision 2x IR lamp
Working time ~8 hours continuously
Standby time ~30 days
Charge time ~6 hours
Outdoor
unit
External power 9~16V DC/AC
Power DC 9V
Consumption 400mA
Outline dimension 200 x 150 x 27 mm
Weight 387 g
Environmental temperature –0°C ~ +40°C
Placement Wall hung type or table style
LCD size 7" TFT color screen
Display resolution 640 x 480
Wireless communication mode
2.4GHz
External power DC 9V / 2A
Indoor
monitor
Application distance About 300m in open space
Product Diagram
Outdoor unit
A. Outdoor unit keys
1. Doorbell key“Call”: ring the bell and trigger video taking when pressed.
2. Reset: erase the communication code

Indoor monitor
Key introduction
A. Indoor monitor Keys (8 key)
1. “OK” key: ON/OFF * Talking * work as confirm key for MENU
2. “↑UP/ Video” key: work as option key for MENU * as video key when
calling or monitoring * as option key when calling extension monitor.
3. “↓DOWN/ Photo” key: work as option key for MENU * as photo key when
calling or monitoring * as entrance key for exposure adjust * as option key
when calling extension monitor.
4. “EXIT / monitor” key: work as monitor key for standby mode * as exit key
for MENU
5. “MENU / unlock” key: work as unlock key when communicating with
outdoor unit * as right moving key for MENU.
6. Brightness
7. Colour
8. Volume: increase and reduce for adjustment.
Installation Guide
Outdoor unit shall be installed at 1.4 ~ 1.7 meter above the floor, and the camera
shall avoid facing the sunlight directly.

Installation Steps & Battery Installation
1. Drill a hole refer to the dimension, put the screw rubber plug in, then fix the
rainproof cover on the wall by screws.
2. Connect the charging line according to the wiring diagram(the hole for wire
getting through suggested 16~30mm), if charging line comes from indoor,
lead the charging line pass through the hole, if charging line comes from
outdoor，lead the charging line pass through the bottom of rainproof cover
and connect the line .
3. Install rechargeable lithium battery to outdoor unit, the unit starts up
automatically.
4. Put the top part of outdoor unit into the rainproof cover like the picture, push
the bottom part, make sure its steady and fix it from the bottom by screw, then
fit on the screw cover.
Unlocking Setting
Menu- -》setup- -》unlock set
Attentions during Installation
1. The outdoor photosensitive sensor should not be hidden or blocked by other
objects.
2. Do not face outdoor unit to sunlight directly.
3. Do not stick label on the speaker, otherwise, the sound effect of doorbell will
be affected.
4. Install the connection line correctly; otherwise, door phone disabled may be
caused.

Wall holder Installation
Table holder Installation
Installation of MicroSD memory card
1. Insert the storage card in the way as shown in the diagram until you hear a
clicking sound.
2. Improper insertion of storage card may cause system failure, please confirm
the inserting direction of the card.
3. Take out of the storage card. Push in the storage card until you hear a clicking
sound, then the storage card will pop up.
Storage Card Introduction
● This product adopts MicroSD card as external storage device, when there is
no storage card in the product, the photo-taking and video-recording
functions are unrealizable.
● If a self-provided storage card is used: Use a storage card with Class 4 or
above. Up to 4G storage card supported. This machine has automatic cyclic
storage function, when the storage card is full, the original file will be
overwritten. This machine can connect to computer by USB line. Or take out
the MicroSD card and connect to computer by card reader.
ATTENTION: do not distort, extrude or strike the storage card, otherwise
the audio-video material recorded on it may be damaged.

Functions and Applications
Outdoor Unit Starting Up
Connect to external power to start up. If the power source is only battery, main
MCU is worken about every one second. Sleep mode saves power (Monitor and
alarm functions could be realized in both two power supply conditions.). When
external power and battery supply power simultaneously, the effect is same to
external power supports the unit only, when battery is in low power, the external
power will charge the battery automatically, green LED flashes every one second,
it recovers to its previous state when the battery is full..
Indoor Monitor Starting Up
Plug in 9VDC power, long press “OK” key about 3 seconds to start up (about 1
second after shutdown), logo shall be displayed on screen with a sound of “Beep”.
Turn into standby mode.
■ Display: standby picture, unit ID, signal sign, power sign, time & date
■ Red LED flashes every 4 seconds.
■ In this mode, the screen shall be dimmed after some seconds and turns
into power saving mode.
■ If there is any calling record under this mode, red LED flashes every 1
second and stops flashing after checking.
■ In standby mode, long press “OK key” about 3 seconds, “Shutdown” shall
be displayed on screen with a sound of “Beep”, the unit switches off.
Outdoor Unit Call Indoor Monitor
In standby time mode, press “Door bell key” to call, the blue LED of the outdoor
unit lights up with a sound of “Du Du”. Blue LED of indoor monitor lights up, the
screen shows image and the unit rings for Max. 30 seconds. If there is no reply
signal from indoor monitor, the outdoor unit stops the Call and recall is allowed.
■ Intercom: press “OK” on indoor monitor -》ring stop and the unit turns into
intercom mode, red LED of indoor monitor is off as well as blue LED is on,
intercom time is Max. 90seconds.
■ Monitor: press “ ” monitor key on indoor monitor-》red LED lights up,
monitor outdoor voice without being discovered by the visitors. (One or
both way intercom could be changed over by pressing “ ” and “OK”, and
it will time again till 90seconds.).
■ Unlock: in “OK” on-state mode -》press “ ” unlock key -》after
successful unlocking, it shows unlock icon.
■ Take a Photo: in “OK” on-state mode -》press “ ” photo taking key -》
one press one photo, the photos will be stored in MicroSD card.
■ Video Recording: in “OK” on-state mode -》press “ ”video taking key
-》start taking video -》press “ ” video taking key again to stop, the
videos will be stored in MicroSD card.
■ Exit: in “OK” on-state mode -》press “OK” key ,the unit turns into standby
mode with a sound of “Beep”.
■ Automatic video: if nobody answers the call in 5 seconds, indoor monitor
starts taking video automatically (Default is automatic video. If setting is
manual video, once connected, the indoor unit will take video manually) till
being stopped or max. taking time.

Indoor Monitor View the Camera
In standby mode, press “ ” monitor key on indoor monitor to monitor call. In
this mode, the blue LED lights up. If outdoor unit receives signal in 5 seconds,
then it connects to indoor monitor, indoor machine turns into normal monitor
mode and shows image and speaks voice of outside. There is no voice speaking
for outdoor unit. If outdoor unit doesn’t receive signal in 5 seconds, then it shows
“User not online” and exits monitor calling mode automatically and turns into
standby mode.
Two sets of outdoor units (Code connected successfully):
Press “ ” monitor key on indoor monitor to turn into monitor selection menu
-》press “↑/↓” key to choose code of outdoor units -》press “OK” to turn into
monitoring call mode, blue LED lights up (During selection, press “Exit” to turn
into standby mode ).
■ Intercom: in monitor mode, red LED lights up, there is voice speaking for
indoor monitor but not for outdoor unit -》press “ ” to turn into both-way
communication, blue LED shuts down -》press “ ” monitor key again to
turn back to one way voice monitor mode. (One or both-way voice could be
changed over repeatedly). Intercom time is 90seconds and shall be timed
again after changing over.
■ Unlock: in “OK” on-state mode -》press “ ” unlock key -》after
successful unlocking, it shows unlock icon.
■ Take a Photo: in monitor mode -》press “ ” photo taking key -》one
press one photo, the photos will be stored in MicroSD card.
■ Video Recording: in monitor mode -》press “ ”video taking key -》
start taking video -》press “ ” video taking key again to stop, the videos
will be stored in MicroSD card.
■ End: in monitor mode -》press “OK” key -》end monitor and turn back to
standby mode.
Note: in monitor mode, red LED lights up, in intercom mode, red LED shuts
down.
Indoor Monitor CALL Indoor Monitor (Intercom)
(Only can realize when there are 2 and more indoor monitors.)
In standby mode, if there are only two indoor monitors in system, press “OK” to
call another indoor monitor.
In standby mode, if there are three indoor monitors in system, press “↑” to call
small code indoor monitor; press “↓” to call large code indoor monitor;
■ If the CALLED indoor monitor doesn’t receive the signal in 4 seconds, the
CALLmonitor shows “User not online”, it turns back to standby mode with a
sound of “Beep”.
■ If the CALLED indoor monitor receives the signal, two monitors play music,
red LED lights up.
■ If the CALLED indoor monitor doesn’t reply, the monitors turn into standby
mode after 30seconds.
■ If the CALLED indoor monitor replies by pressing “Ok”, music stops, red
LED shuts down, blue LED lights up to both of the monitors, and both
monitors turn into intercom mode, communication time is max. 90seconds.
■ The CALL indoor monitor has initiative hang up function.
■ During communication, if any end in the communication presses “OK”, then
both two ends hang up with a sound of “Beep” and turn to standby mode.

Night-vision
With night-vision function, even under the environment of extremely poor visibility,
the outdoor unit can activate infrared lamps and recognize clearly objects or
people within the distance of 1.5meter (the best focus of this product is 0.8 meter).
In addition, under complete black condition, it displays black and white effects.
NOTE: Please keep the lens of infrared lamps clean.
Bright/Colour/Volume Adjustment
In image communication mode.
■ Push “Brightness” key to adjust brightness, every press adjusts one
grade.
■ Push “Color” key to adjust color, every press adjusts one grade.
■ Push “Volume” key to adjust volume, every press adjusts one grade.
Tamper Alarm Function
It shall alarm if outdoor unit is detached from the shell. The indoor monitors shall
alarm as well as display image once the outdoor unit alarms, and the indoor
monitors shall produce an alarm file. The indoor monitors alarms for max.
2minutes. Press “OK” key to stop alarm.
NOTE: The outdoor unit only could work when it is repowered on and
reinstalled into the shell.
USB Function Description
In standby mode, with MicroSD card in the monitor, plug in USB wire, the screen
shall display a selection menu: “USB”, “POWER”
■ Choose “POWER by pressing “↑/↓”, the USB only serves as charging
function, the indoor monitor works as normal.
■ Choose “USB” by pressing ↑/↓”, connect the monitor with the computer and
read the files through computer.
Indoor Monitor Menus
■ In standby mode, press “MENE” to turn into main menu.
■ Choose submenu by pressing “↑/↓”and “MENU”, press “Ok” to confirm.
REMARK: Turn back to previous menu by pressing “EXIT” in submenu, turn
back to standby mode by pressing “EXIT” in main menu.
Video
Turn into video menu and operate.
■ If there is no MicroSD card, screen displays “No MicroSD Card” and turns
back to main menu.
■ If there is MicroSD card but no video record, screen displays “No File!” and
turns back to main menu.
■ If there is MicroSD card and video record, screen displays video list by time
order, newest file is listed on the top.
■ Choose operating command “Play”, “Delete”, “Delete All” or “Back” by
pressing “↑/↓” -》press “OK” to turn into operating.
■ In Play mode -》press “OK” to pause and play -》press “EXIT” to exit.
■ After operation, exit automatically or by pressing “EXIT” to turn back to
video operation menu.
Photo
Turn into photo menu and operate.
■ If there is no MicroSD card, screen displays “No MicroSD Card” and turns
back to main menu.
■ If there is MicroSD card but no photo record, screen displays “No File!” and
turns back to main menu.
■ If there is MicroSD card and photo records, screen displays photo list by
time order, newest file is listed on the top.

■ Choose operating command “View”, “SetAs Background”, “Delete”, “Delete
All” or “Back” by pressing “↑/↓”-》press “OK” to turn into operating.
■ In View mode -》press “↑” to view the last photo, press “↓” to view the next
photo
■ After operation, press “EXIT” to turn back to photo operation menu.
Info
Turn into “Record” to check call history.
■ If there is no call history, screen displays “No files”.
■ Choose operating command “Play” or “Delete” by pressing “↑/↓”, press
“OK” to turn into operating
■ If there is no MicroSD card, choose command “Play”, the screen displays
“No Video File!” and turns back to Call History menu.
■ In Play mode -》press “Ok” to pause and play -》press “EXIT” to exit
■ When choose “Play” and if there is not MicroSD card, screen displays “No
Video File!” and turns back to Call History Menu.
■ In Play mode -》press “OK” to pause and play -》press “EXIT” to exit.
■ After operation, press “EXIT” to turn back to call history operation menu.
NOTE: Unplug the power and reset, all the call history will disappear.
Mode-vd
Enter into “Mode-vd” to set up video.
■ Press“↑/↓”key -》set up “Automatically records” or “Manual records” -》
press ”OK” key to confirm and exit. Default setting is auto video (with
MicroSD card) and manual photo.
■ Press “EXIT” key to turn back to standby mode step by step.
NOTE: Auto video: If nobody replies in 5 seconds after connection, the indoor
monitor starts up auto video (Factory default is auto video, if manual video is set,
video recorded after calling) till being stopped or max. record time.
Detection
Enter into Sense setup menu.
■ Press“↑/↓”key -》choose “Close to detect” or “Open detection” -》press ”OK”
key to connect to outdoor unit -》you see on display „Connecting…”.
press ”OK” key to confirm and exit
■ screen displays “success” when it finish
Admin
Enter into Security Password menu.
■ Press “MENU” key to choose figure of old or new password.
■ Press“↑/↓”key -》adjust figure -》press “OK” key to set up
■ If original password is right, screen shows “success!”, and then return to the
setup menu.
■ If original password is wrong, screen shows “password error”, and then
return to code match menu, please set up again
■ Press “EXIT” key to turn back to standby mode.
Network
Enter the network Menu, input password (0000). If the password is wrong, screen
shows "Password error!", "Please input again!" please input the right password.
Match code function: match code; give code; receive code; inform:
● Match code (Outdoor unit should connect to the Indoor monitor)
■ Select “Creating a network” on indoor monitor -》press “OK” key-》enter
into the match code mode
■ Under the standby mode of outdoor unit -》long press “call” key-》loosen
key until the sound of a “Beep” , enter into the match code mode

■ If two units match successfully in 16 seconds, indoor monitor displays
“Success”, outdoor unit makes “Beep- Beep-Beep” sounds, as the first
outdoor unit
■ If matching failed in 16 seconds, indoor monitor shows “failed”, the outdoor
unit makes ”Beep” sound
■ Press “EXIT” key on the indoor monitor, exit menu, enter into the standby
mode
Note: If failed match, rematch the code after connection, otherwise, rematch
the code after clear the code
1. Indoor monitor clear code method: refer to the menu function -》network -》
Leave the network
2. Outdoor unit clear code method:
A. Transformer supply: long press “Reset” key about one second, code cleared
after a “tick” sound.
B. Battery supply: press “Reset” key and “doorbell key” at the same time till a
“Beep”, code cleared.
Pairing Additional Monitors or outdoor unit
NOTE: By default, the monitor is paired with the outdoor unit. These
instructions apply to paring a second or third monitor.
● Start the network & Join the network (match more indoor monitors and
outdoor units ):
■ Choose “Start the network” on the old indoor monitor -》press “OK” key-》
enter into “Start the network” mode
■ Added indoor monitor enters into the network menu -》choose “Leave the
network” -》press “OK” key -》and then choose “Join the network” -》press
“OK” key -》enter into the Join the network mode.
■ If code receiving finished in 16 seconds, exit code receiving mode after
three “beep” sounds, and then enter into code menu.
■ Setup the user ID number for the new monitor.
■ The added outdoor unit(finished clear code), under the standby mode-》
keep pressing ”call” key for 6 seconds until two “beep” sounds(“beep” once
about 3 seconds) -》loosen the key to enter into Join the network mode.
■ Outdoor unit make three “beep” sounds if receive code successfully, and as
No. 2 outdoor unit.
■ If failed to receive code in 16 seconds, exit receive code mode after one
“beep” sound. Enter into the Code Menu (Outdoor unit enters into the
standby mode)
■ After code receiving finished, press ”OK” key on code give unit to exit the
code give mode, enter into the code menu.
■ Press “EXIT” key to return to MENU gradually, then enter into standby
mode
■ After all units receive code finished, please use the No. 2 outdoor unit call
all indoor monitors, if all code matched, receive code successfully; if not,
clear code of the new unit (don’t clear the code giving unit), reform the
code giving and code receiving again.
NOTE:
1.Do not set same ID number for every indoor monitors and outdoor units.
2.The original Password for code match menu is“0000”.
3.Inform function: after match code, give code, receive code, clear code and reset
ID number, please inform. Inform: tell all units the pieces and ID numbers in the
system.
4.Method of inform: outdoor unit calls all the indoor monitors (all indoor monitors
should be matched), if there are two outdoor units, use the No. 2 outdoor unit to
inform.
● Clear Code (Leave the network)
Indoor monitor clear code method:
Choose “network” option, press “OK” key to enter into password menu.
■ Input the password to enter into code match menu (original password is
0000).If you input wrong password, system will inform you “Password
Error!”, “Please Input Again!”, enter into the code match menu until input
the right password

■ Press “↑/↓”key -》choose “Leave the network” -》press “OK” key, enter into
clear code menu.
■ Press “↑/↓”key -》choose “Yes” (press “Quit” to exit if you don’t want to clear
anything ), system will return to code menu automatically after code clear
confirmed
Outdoor unit clear code method:
■ long press “Reset” key -》install the battery -》till a second “Beep”-》loosen
the key to enter into Join the network mode
■ Outdoor unit make three “beep” sounds if clear code successfully
User
Enter into Own ID Number to set up ID.
■ Press“↑/↓”key -》set up ID number -》press ”OK” key -》confirm and exit ID
Number setup menu
■ Press “EXIT” key to turn back to standby mode step by step.
NOTE: Do not repeat ID number for every indoor monitors and outdoor units.
Standby
Enter into Backlight Time menu to set up standby time, exit menu automatically
after setup.
■ Press“↑/↓”key-》increase and reduce standby time(10s-60s) -》press ”OK”
key to setup and return to Backlight Time Setup menu.
■ Press “EXIT” key to enter into the standby mode.
Time
Enter into Time and Date Setup menu.
■ Press “MENU” key to choose figure of time or date.
■ Press“↑/↓”key to adjust the figure
■ Press “OK” key to set up and return to Date Setup menu
■ Choose “Show”, set “Y”, date will show. Set “N”, date will not show
■ Press “EXIT” key to enter into the standby mode
Ring
Enter into Ring menu.
■ Press“MENU”key -》increase and reduce volume(1 (lower volume) & 8
(higher volume), there are a total of 8 volume levels) -》press “OK” key to
set up and return to menu.
■ Press “EXIT” key to turn back to standby mode
Language
Enter into Language menu.
■ Press“↑/↓”key -》set up “Language” -》press ”OK” key to confirm and exit
■ Press “EXIT” key to turn back to standby mode

Setup
Enter into Setup menu.
■ Press“↑/↓”key -》Select item -》press ”OK” key to confirm
■ “Unlock set” --setup unlocking time: press “OK” and put the Network
password select from 3s,6s or 8s & confirm with “OK”.
■ “Alarm settings”--setup “ press “OK” and put the Network password. When
password ok you see the following option: Open/Close/Clear history”
■ “Equipment selection”--select “USB or Power” when connect to PC and
press “OK”
■ “Restore settings”--setup “Yes” or “No”
■ Press “EXIT” key to turn back to standby mode
Format
Enter into MicroSD format menu.
■ Press“↑/↓”key -》set up “Yes”, all files on MicroSD card will be erased or
“No”, you go back to the main menu without any changes -》press ”OK” key
to confirm and exit
■ Press “EXIT” key to turn back to standby mode
Version
Enter into Version menu.
■ Press “OK” key to view version, return to setup menu
■ Press “EXIT” key to turn back to standby mode step by step
Battery and Charge
● Under the connection mode, when the outdoor unit is at low power, the
indoor monitor will show “out low power” to remind you to charge for outdoor
unit.
● This product can be charged by charger or by USB date line connected to
computer, or remove the lithium battery, charge by the universal charger,
support working while charging.
● Battery type: this product with high-quality battery.
● Charging and battery attentions, please reference the chapter “Warms and
attentions” in this manual.
NOTE: Under the low power, video-recording, photo-taking and card reader
function cannot work normally.
Accessories
Manual, Waterproof case, Outdoor unit, Indoor monitor, Wall hung holder, 2x
Charger (DC 9V), DC line, Lithium battery, 2x Screw M3, 7x Screw for waterproof
case and holder
Statement
The standard configuration for KiVOS door phone is one indoor monitor and one
outdoor unit. The door phone has finished code match and can be used directly. If
you need more pieces of indoor monitors or outdoor units, please contact your
local distributors (Maximum 2 outdoor units to 3 indoor monitors supported). For
the added units, please reference the Give Code and Receive Code in the Code
Menu.

General faults and solutions
Cause(s) Solution(s)
Can not start up
Neglected to press switch button Press switch button
Lithium battery is not installed Install lithium battery
Low battery Charge up lithium battery
No connection to power adapter when
battery runs out Connect to power adapter
Cannot charge
Adapter connector does not connect to
charging port of machine correctly
Reconnect correctly
Adapter does not connect to 110V- 240V
alternating current
Plug into the socket to connect to
alternating current
Outdoor unit cannot call or connect to indoor monitor
Code match failed Clear code, and re-match code
Indoor monitor cannot call Indoor monitor
Code match failed
Worry ID number
Clear code, and re-match code
Setup ID number
Image has noisy point or flickers
Handset is placed near to TV player,
microwave oven, daylight lamp or mobile
phone which produces electromagnetic
wave interference
Keep handset far away from the
interference items
No signal for indoor monitor
Outdoor unit does not connect to the
power
Connect to the power
Distance between outdoor unit and
Indoor monitor is too far Adjust to appropriate distance
Disturbed by magnetic field around Keep handset far away from
magnetic field
Security and Disposal Hints for Batteries: Hold children
off batteries. When a child swallowed a battery go to a
doctors place or bring the child into a hospital promptly!
Look for the right polarity (+) and (–) of batteries! Always
change all batteries. Never use old and new batteries or
batteries of different types together. Never short, open,
deform or load up batteries! Risk of injury! Never throw
batteries into fire! Risk of explosion!
Hints for Environment Protection: Packages materials
are raw materials and can be recycled. Do not disposal old
devices or batteries into the domestic waste. Cleaning:
Protect the device from contamination and pollution (use a
clean drapery). Avoid using rough, coarse-grained materials
or solvents/aggressive cleaner. Wipe the cleaned device
accurately. Important Notice: Should battery fluid leak from
a battery, wipe the battery case with a soft cloth dry.
Distributor: Technaxx Deutschland GmbH & Co.KG,
Kruppstr. 105, 60388 Frankfurt a.M., Germany