TechNexion SBC-APL-350 User manual

3.1 Surface Mounng
4External Connectors
SBC-APL-350
Quickstart Guide
3 Installaon Instrucons
This secon describes the mounng procedures for SBC series device. The material in the mounng area must provide sufficient strength for support of this single board
computer.
There are 4 mounng holes (M3) on the PCB required for surface mounng. Four M3 screws with at least 8mm head-to-p length are required to secure this device to
the surface. The distance from the PCB to the surface must be at least 1.6mm.
INNOVATORS OF TECHNOLOGY
Front view:
Front view:
2Dimensions
1 Safety Precauons
Thank you for purchasing a TechNexion SBC series device. This installaon guide will be helpful in the installaon, wiring and inspecon of your TechNexion single board
computer. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precauons before proceeding with the
installaon, wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference. The following suggesons will help you.
• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,
allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage baeries, and warp or melt certain plascs.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
• Do not aempt to open the device. This product is designed for specific applicaons and needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operaon.
• Unauthorized modificaons or aachments could damage the device and may violate regulaons governing radio devices.
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to bad venlaon or overheang.
These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service
facility for service.
•Make sure that the available power source matches the required input power of the device. Failure to observe this cauon may result in electric shock or fire.
•Do not power the unit by DC input when you apply power over the PoE (RJ45).
1.1 Storage and Installaon
1.2 Wiring
1.3 Maintenance and Inspecon
!
Unit : mm
Description No.No. Description
1
2
3
4
5
6
12
13
14
15
16
17
7
8
9
10
11
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Power button
USB OTG (Type-C) connector
microSD card slot
Micro-SIM card slot
SATA 3.0 connector
3.5mm audio jack
18/24-bit LVDS jumper
SATA Power connector
LVDS1 connector
LVDS2 connector
M.2 KEY-E slot (PCIe + USB 2.0)
M.2 KEY-B slot (SATA + USB 2.0)
FAN1 header
USB (1 port) header
SO-DIMM DDR3L slot
RTC Battery connector
USB (2 ports) header
Power Fuse
Power Input connector
CMOS jumper
COM-PWR1 jumper
FPANEL1 front panel switch
Serial Port (COM1) DB9 connector
Serial Port (COM2) header
GPIO (DIO1)) header
LAN1 RJ45 connector
LAN2 RJ45 connector
USB Host connector
USB Host connector
miniDP1 connector
miniDP2 connector
1 2
20.4
1.6
10.7
4.25
147
3.42
102
95.2
72.21 41
41
113.21
42.75
83.75
n
3.1
h<1mm
138.5
h<1mm
68
31 2 4 579
10 11 16 17
1824 2325262728/293031 19
12 13 14 15
202122

• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmied, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior wrien permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied by law no liability (including liability to any person by reason of
negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version at: hps://www.technexion.com/support/download-center/
Phone: [phone] Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan © 2001-2019 TechNexion Ltd.
2019-11-19
5.1 Digital I/O Headers (GPIO/DIO1)
5 Pin Definion
This product is available with two non-galvanic isolated GPIO headers: GPIO external connector and DIO1 internal
header. The headers have the following pinout:
The unit is by default preloaded with soware that can download and install a selecon of Linux OS images over hardwired network. Simply connect a display to the
unit though the miniDP connector and a network through the Ethernet LAN RJ45 connector and power it up, then follow the steps on the screen to load the
soware.Local proxies will interfere with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/
To download drivers for the Windows operang systems, go to our Download Center at:
hps://www.technexion.com/support/download-center/
For more informaon about installing and configuring the Windows operang systems, see: hps://msdn.microso.com/en-us/
6 Soware and Driver Installaon
3 4
Header on SBC-APL-350: DB15 (15-pin) high density D-Sub male connector.
Cable receptacle: DB15 (15-pin) high density D-Sub female connector.
GPIO:
Port Pin #
Signal
1
2
3
4
5
7
6
8
9
10
11
12
13
14
15
VCC
GPIO1
GPIO3
GPIO5
GPIO7
GND
GND
GND
GND
GND
VCC
GPIO2
GPIO4
GPIO6
GPIO8
Description Voltage
Supply output
DIG_IN1/OUT1
DIG_IN3/OUT3
DIG_IN5/OUT5
DIG_IN7/OUT7
Common Ground
Common Ground
Common Ground
Common Ground
Common Ground
Supply output
DIG_IN2/OUT2
DIG_IN4/OUT4
DIG_IN6/OUT6
DIG_IN8/OUT8
5V
3.3V
3.3V
3.3V
3.3V
5V
3.3V
3.3V
3.3V
3.3V
1
11
6 10
15
5
Port Pin #
Signal
1
2
3
4
5
6
NC
NC
USB_D+
USB_D-
VBUS
GND
Description
5V Universal Serial Bus Power
Ground
NOTE: DB15 GPIO cable is available for this header(oponal). The DB15 connector pinout is the same as the
GPIO connector (see above for details).
Header on SBC-APL-350: 2x5-pin Header (2.00 Pitch Male Header).
Cable receptacle: 2x5-pin Header (2.00 Pitch Female Header).
DIO1:
Header Pin #
Signal
1
2
3
4
5
7
6
8
9
10
VCC
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
GPIO8
GND
Description Device
Supply output
DIG_IN1/OUT1
DIG_IN2/OUT2
DIG_IN3/OUT3
DIG_IN4/OUT4
DIG_IN5/OUT5
DIG_IN6/OUT6
DIG_IN7/OUT7
DIG_IN8/OUT8
Common Ground
5V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
1357
2468
9
10
5.2 Serial Ports (COM1/COM2)
This product is available with two full funcon non-galvanic isolated RS-232 serial ports: COM1
external connector and COM2 internal header. The ports have the following pinout:
COM1:
Header on SBC-APL-350: DB9 (9-pin) standard D-Sub male connector.
Cable receptacle: DB9 (9-pin) standard D-Sub female connector.
Header on SBC-APL-350: 2x5-pin Header (2.00 Pitch Male Header, Pin 10 = KEY).
Cable receptacle: 2x5-pin Header (2.00 Pitch Female Header, Pin 10 = KEY).
NOTE: DB9 RS-232 cable is available for this header(oponal). The DB9 connector
pinout is the same as the COM1 port.
Port Pin #
Signal
1
2
3
4
5
7
6
8
9
SERIAL1_DCD
SERIAL1_RXD
SERIAL1_TXD
SERIAL1_DTR
GND
SERIAL1_DSR
SERIAL1_RTS
SERIAL1_CTS
VCC*
Description Device
Port#1 Data Carrier Detect (input)
Port#1 Receive data (input)
Port#1 Transmit data (output)
Port#1 Data Terminal Ready (output)
Ground
Port#1 Data Set Ready (input)
Port#1 Request-to-send (output)
Port#1 Clear-to-send (input)
5V supply output
COM1
COM1
COM1
COM1
COM1
COM1
COM1
1
6 9
5
COM2:
Header Pin #
Signal
1
2
3
4
5
7
6
8
9
10
SERIAL2_DCD
SERIAL2_RXD
SERIAL2_TXD
SERIAL2_DTR
GND
SERIAL2_DSR
SERIAL2_RTS
SERIAL2_CTS
VCC*
NC
Description Device
Port#2 Data Carrier Detect (input)
Port#2 Receive data (input)
Port#2 Transmit data (output)
Port#2 Data Terminal Ready (output)
Ground
Port#2 Data Set Ready (input)
Port#2 Request-to-send (output)
Port#2 Clear-to-send (input)
5V supply output
Key
COM2
COM2
COM2
COM2
COM2
COM2
COM2
1357
2468
9
5.3 LVDS Connectors (LVDS1/LVDS2)
Header on SBC-APL-350: Hirose DF13-40DP-1.25V (1.25mm Pitch Double Row Straight Pin Header).
Cable receptacle: Hirose DF13-40DS-1.25C (1.25mm Pitch Double Row Socket, Crimping Socket).
Header on SBC-APL-350: Molex 53780-0670 (1.25mm Pitch PanelMate Header, Surface Mount, Right-Angle,
1.90mm Height, 6 Circuits).
Cable receptacle: Molex 51146-0600 (1.25mm Pitch PanelMate Wire-to-Board Receptacle Housing, Ultra Low
Profile, 6 Circuits, Natural).
Header on SBC-APL-350: Molex 89400-0220 (2.00mm Pitch Wire-to-Board Header, Vercal, 2 Circuits, with
Kinked PC Tail).
Cable receptacle: Molex 87369-0200 (2.00mm Pitch Crimp Housing, Single Row, 2 Circuits, Natural).
This product features two (dual channel) LVDS connectors) for connecng to a (single or dual channel) LVDS panel: LVDS1 / LVDS2.
5.4 USB Touch Header (USB1)
This product features one USB Touch Header: USB1.
5.5 SATA Power Header (SATA_PWR1)
This product features one SATA Power header: SATA_PWR1.
LVDS1 / LVDS2:
USB1:
SATA_PWR1:
Header Pin # Pin #
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
12V
5V
12V
5V
LCD_ENB
PWM_5V
LCD_ENBK
PWM_3V
GND
GND
SEL18/24bit
3.3V
LVDS_D0-
3.3V
LVDS_D0+
LVDS_REV
GND
LVDS_R/L
LVDS_D1-
LVDS_U/D
Signal
LVDS_D1+
SCL
GND
SDA
LVDS_D2-
LED_enable
LVDS_D2+
LED+
GND
LED+
LVDS_CLK-
LED+
LVDS_CLK+
LVDS_enable
GND
LED-
LVDS_D3-
LED-
LVDS_D3+
LED-
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
13 2456
Header Pin #
Signal
1
2
+5V
GND
Description
5V Universal Serial Bus Power
Ground
1
2
USB differential pair signal
Header Pin #
Signal
1
2
3
4
GND
ON-OFF
GND
PWR-LED
Ground
Power button
Ground
Power LED
GND
RESET
GND
SATA-LED
Ground
Reset button
Ground
SATA LED
Description Pin #
Signal
5
6
7
8
Description
NOTE: for descripon of other jumpers / headers not covered in this document – please refer to the
SBC-APL-350 HARDWARE MANUAL.
5.6 Front Panel Switch (FPANEL1)
This product features FPANEL1 front panel switch.
1357
2468