Technika 42-2020 User manual

COLOUR TELEVISION WITH REMOTE CONTROL
OPERATING INSTRUCTIONS
For assistance, please call our Tesco Electrical Helpline on 0845 4566767
42-2020

English - 1 -
Contents
Features ................................................................. 2
Accessories ............................................................ 2
Introduction............................................................. 2
Preparation............................................................. 2
Safety Precautions ................................................. 3
Power Source ..................................................... 3
Power Cord......................................................... 3
Moisture and Water ............................................ 3
Cleaning.............................................................. 3
Ventilation ........................................................... 3
Heat and Flames ................................................ 3
Lightning ............................................................. 3
Replacement Parts ............................................. 3
Servicing............................................................. 3
Waste Disposal................................................... 3
Information for Users in European Union
Countries ............................................................ 3
Disconnecting the Device ................................... 3
Headphone Volume ............................................ 4
Installation........................................................... 4
LCD Screen ........................................................ 4
Warning .............................................................. 4
Connection to a Television Distribution
System (Cable TV etc.) from Tuner .................... 4
Environmental Information ..................................... 5
Overview of the Remote Control ............................ 6
LCD TV and Operating Buttons.............................. 7
Viewing the Connections- Back Connectors .......... 7
Viewing the Connections - Side Connectors .......... 9
Aerial Connection ................................................... 9
Power Connection .................................................. 9
Using Digital Multimedia Connectors.................... 10
USB Memory Connection ................................. 10
Connecting the LCD TV to a PC........................... 10
Connecting to a DVD Player................................. 10
Using Side AV Connectors ....................................11
Using Other Connectors........................................11
Connecting Other Equipment via Scart .................11
Inserting Batteries in the Remote
Control Handset.....................................................11
Switching the TV On/Off ....................................... 12
To Switch the TV On ......................................... 12
To Switch the TV Off ......................................... 12
Input Selection...................................................... 12
Basic Operations .................................................. 12
Operation with the Buttons on the TV............... 12
Operation with the Remote Control .................. 12
Initial Settings ....................................................... 13
General Operation................................................ 14
Information Banner ........................................... 14
Electronic Programme Guide (EPG) .................... 14
Displaying Subtitles .......................................... 14
Digital Teletext (** for UK only) ......................... 15
Analogue Teletext ............................................. 15
Widescreen....................................................... 15
IDTV Menu System .............................................. 15
Channel List...................................................... 15
Timers............................................................... 17
Conditional Access ........................................... 17
TV Setup........................................................... 18
Setup ................................................................ 18
Media Browser.................................................. 22
Playing MP3 Files............................................. 22
Viewing JPG Files............................................. 23
Slideshow Options............................................ 23
Video Playback ................................................. 23
Analogue TV Menu System.................................. 23
Picture Menu..................................................... 23
Sound Menu ..................................................... 24
Feature Menu ................................................... 25
Install Menu ...................................................... 27
Source Menu .................................................... 28
PC Mode Menu System........................................ 28
PC Position Menu............................................. 28
Displaying TV Information .................................... 29
Mute Function....................................................... 29
PIP (Picture-in-Picture) and PAP
(Picture-and-Picture) Modes................................. 29
Picture Mode Selection......................................... 29
Freezing Picture ................................................... 29
Zoom Modes......................................................... 30
Teletext ................................................................. 30
Tips....................................................................... 31
Appendix A: PC Input Typical Display Modes....... 32
Appendix B: AV and HDMI Signal Compatibility
(Input Signal Types).............................................. 32
Appendix C: Supported DVI Resolutions.............. 33
Appendix D: PIP/PAP Mode Combinations .......... 33
Appendix E: Supported File Formats for
USB Mode ............................................................ 34
Specifications ....................................................... 35
Important Instruction............................................. 36

English - 2 -
Features
• Remote controlled colour LCD TV.
• Fully integrated digital TV (DVB-T).
• HDMI connectors for digital video and audio. This
connection is also designed to accept high definition
signals.
• USB input.
• 200 programmes from VHF, UHF(analogue).
• 300 programmes for digital mode (IDTV).
• On Screen Display (OSD) menu system.
• Two scart sockets for external devices (such as
video, video games, audio set, etc.).
• Stereo sound system. (German+Nicam)
• Teletext, fastext, TOP text.
• Headphone connection.
• Automatic programming system.
• Forward or backward manual tuning.
• Sleep timer.
• Child lock.
• Automatic sound mute when no transmission.
• NTSC playback.
• PIP / PAP / PAT functions.
• AVL (Automatic Volume Limiting).
• When no valid signal is detected, after 5 minutes the
TV switches itself automatically to standby mode.
• PLL (Frequency Search).
• PC input.
• Plug&Play for Windows 98, ME, 2000, XP,
Windows 7, Vista.
• Audio line out.
• Game Mode (optional).
• Active antenna power (optional).
Accessories
SUBTITLE SLEEP
F
INO/
PESTR E
RETURN
V
P
1
4
7
2
5
8
3
6
9
JKL
STU
DEF
MNO
VWX
PQR
YZ
M
OK
GHI
SOURCE
ABC
EPG
0
SCREEN LANG
FAV TV DTV
SAPW
Remote
Controller
Batteries: 2 X AAA
Instruction Book
Introduction
Thank you for choosing this product. This manual will
guide you for the proper operation of your TV.
Before operating the TV, please read this
manual thoroughly.
Please do keep this manual in a safe place for
future references.
Preparation
For ventilation, leave a free space of at least 10 cm
all around the set. To prevent any fault and unsafe
situations, please do not place any objects on top
of the set.
Use this device in moderate climates.
10 cm
10 cm
10 cm

English - 3 -
Safety Precautions
Please read the following recommended safety
precautions carefully for your safety.
Power Source
The TV set should be operated only from a 220-240
V AC, 50 Hz outlet. Ensure that you select the correct
voltage setting for your convenience.
Power Cord
Do not place the set, a piece of furniture, etc. on the
power cord (mains lead) or pinch the cord. Handle the
power cord by the plug. Do not unplug the appliance
by pulling from the power cord and never touch the
power cord with wet hands as this could cause a short
circuit or electric shock. Never make a knot in the cord
or tie it with other cords. The power cords should be
placed in such a way that they are not likely to be
stepped on. A damaged power cord can cause fire or
give you an electric shock. When it is damaged and
needs to be replaced, it should be done by qualified
personnel.
Moisture and Water
Do not use this device in a humid
and damp place (avoid the bathroom,
the sink in the kitchen, and near the
washing machine). Do not expose this
device to rain or water, as this may be
dangerous and do not place objects
filled with liquids, such as flower
vases, on top. Avoid from dripping
or splashing.
If any solid object or liquid falls into the cabinet, unplug
the TV and have it checked by qualified personnel
before operating it any further.
Cleaning
Before cleaning, unplug the TV set
from the wall outlet. Do not use
liquid or aerosol cleaners. Use soft
and dry cloth.
Ventilation
The slots and openings on the TV
set are intended for ventilation and to ensure reliable
operation. To prevent overheating, these openings
must not be blocked or covered in anyway.
Heat and Flames
The set should not be placed near
to open flames and sources of
intense heat such as an electric
heater. Ensure that no open flame
sources, such as lighted candles,
are placed on top of the TV.
Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
Lightning
In case of storm and lightning or when
going on holiday, disconnect the power
cord from the wall outlet.
Replacement Parts
When replacement parts are required, make sure that
the service technician has used replacement parts,
which are specified by the manufacturer or have the
same specifications as the original one. Unauthorized
substitutions may result in fire, electrical shock or
other hazards.
Servicing
Please refer all servicing to qualified
personnel. Do not remove the cover
yourself as this may result in an
electric shock.
Waste Disposal
Instructions for waste disposal:
• Packaging and packaging aids are recyclable and
should principally be recycled. Packaging materials,
such as foil bag, must be kept away from children.
• Batteries, including those which are heavy metal-
free, should not be disposed of with household
waste. Please dispose of used battery in an
environment friendly manner. Find out about the
legal regulations which apply in your area.
• Cold cathode fluorescent lamp in LCD PANEL
contains a small amount of mercury; please follow
the local laws or regulations for disposal.
Information for Users in European Union
Countries
This symbol on the product or on its
packaging means that your electrical
and electronic device should be
disposed at the end of its service
life separately from your household
wastes. There are separate collection
systems for recycling in EU.
For more information, please contact the local
authority or the dealer where you purchased the
product.
Disconnecting the Device
The mains plug is used to disconnect TV set from
the mains and therefore it must remain readily
operable.

English - 4 -
Headphone Volume
Excessive sound pressure from
earphones and headphones can
cause hearing loss.
Installation
To prevent injury, this device must be
securely attached to the wall in accordance with the
installation instructions when mounted to the wall (if
the option is available).
LCD Screen
The LCD panel is a very high technology product with
about a million thin film transistors, giving you fine
picture details. Occasionally, a few non-active pixels
may appear on the screen as a fixed blue, green or
red point. Please note that this does not affect the
performance of your product.
Warning
Do not leave your TV in standby or operating mode
when you leave your house.
Connection to a Television Distribution
System (Cable TV etc.) from Tuner
Device connected to the protective earthing of the
building installation through the mains connection or
through other apparatus with a connection to protective
earthing-and to a television distribution system using
coaxial cable, may in some circumstances create a
fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).

English - 5 -
Environmental Information
• This television is designed to consume less energy to save environment.
You not only help to save the environment but also you can save money by reducing electricity bills thanks to the
energy efficiency feauture of this TV. To reduce energy consumption, you should take the following steps:
• You can use Power Save Mode setting, located in the Feature menu. If you set Power Save Mode as On,
the TV will switch to energy-saving mode and luminance level of TV set will be decreased to optimum level.
Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
• When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce
energy consumption.
• Disconnect power when going away for longer time.
• Note that annually, using the TV set in Power Save Mode has more power efficiency than disconnecting
the TV from the mains plug instead of keeping stand-by mode. Therefore disconnect the TV from the mains
plug to save energy when you do not use. However it is highly recommended to activate Power Save Mode
setting to reduce your annual power consumption.
• Please helps us to save environment by following these steps.
Repair Information
Please refer all servicing to qualified personnel. Only qualified personnel must repair the TV. Please contact
your local dealer, where you have purchased this TV for further information.

English - 6 -
Overview of the Remote Control
SUBTITLE SLEEP
FIN O/
PESTRE
RETURN
V
P
1
4
7
2
5
8
3
6
9
JKL
STU
DEF
MNO
VWX
PQR
YZ
M
OK
GHI
SOURCE
ABC
EPG
0
SCREEN LANG
FAV
TV DTV
SAP
W
Standby1.
Yellow / Feature menu / Current language (*)2.
(in DTV mode)
Blue / Install menu / Favourite mode (*)3.
(in DTV mode)
PIP / PAP mode4.
Guide (in DTV mode)5.
Sleep timer6.
Subtitle on-off / TXT subtitle7.
Numeric buttons8.
TV – Digital TV mode9.
Volume up10.
Programme up / Page down (in DTV mode)11.
AV / Source selection12.
Info / Reveal (in TXT mode)13.
Return / Exit (in DTV mode) / Index page14.
(in TXT mode)
Cursor up / Page up (in TXT mode)15.
Cursor right16.
OK / Select / Freeze picture / Hold17.
(in TXT mode)
Cursor down / Page down (in TXT mode)18.
Menu on-off19.
Cursor left / Subpage (in TXT mode)20.
Previous Programme / Swap21.
Picture mode selection22.
Programme down / Page up (in DTV mode)23.
Mute24.
Volume down25.
Favourite mode (in DTV mode)26.
Mono-Stereo / Dual I-II / Current language27.
(in DTV mode) (*)
Image size / Expand (in TXT mode)28.
Teletext / Mix / PAT29.
Update (in TXT mode)30.
Red / Sound menu / Channel list (in DTV mode)31.
Green / Picture menu / Subtitle on-off32.
(in DTV mode) (*)
(*) Only for EU country options.

English - 7 -
LCD TV and Operating Buttons
Standby button1.
TV/AV button2.
Programme Up/Down buttons3.
Volume Up/Down buttons4.
Note: Press “” / “ ”
buttons at the same time to view
main menu.
Viewing the Connections- Back Connectors
12
1. S/PDIF Digital Out outputs digital audio signals of the currently watched source.
Use a digital optic cable to transfer audio signals to a device that has S/PDIF input.
2. Subwoofer Out is for connecting an external, active subwoofer to the set to give a much deeper bass
effect.
Use an appropriate RCA cable to connect the set to a subwoofer unit.
Audio Line Outs3. output audio signals to an external device such as an optional sound system.
To connect the external speakers to your TV, use AUDIO LINE OUTS of the TV with an audio cable.

English - 8 -
4. SCART 2 inputs or outputs for external devices.
5. SCART 1 inputs or outputs for external devices.
Connect the SCART cable between SCART sockets on TV and SCART socket on your external
device (such as a decoder, a VCR or a DVD player).
Note:If an external device is connected via the SCART sockets, the TV will automatically switch to
AV mode. If both sockets are employed at the same time, SCART 1 will override SCART 2 unless
manually selected.
Note: You should connect the decoder to EXT-1, if you are planning to watch a scrambled channel.
The decoder might not function properly if you do not connect the decoder to the Scart 1 (Ext-1) socket
Note: Picture state can be affected by scart cable quality.
6. Component Video Inputs (YPbPr) are used for connecting component video.
You can connect the component video and audio sockets with a device that has component output.
Connect the component video cables between the COMPONENT VIDEO INPUTS on on the TV and
the component video outputs of your device. While connecting, be sure that the letters on your TV, “Y”,
“Pb”, “Pr” correspond with your device’s connectors.
7. PC/YPbPr Audio Inputs are used for connecting audio signals of a PC or a device that connects to the
TV via YPbPr.
Connect the PC audio cable between the AUDIO INPUTS on the TV and audio output of your PC to
enable PC audio.
Connect the audio cable between AUDIO INPUTS on the TV and audio outputs of your device to
enable component audio.
8. S/PDIF Coaxial Out outputs digital audio signals of the currently watched source.
Use an SPDIF coaxial cable to trasfer audio signals to a device that has S/PDIF input.
9. RF Input connects to an antenna or a cable.
Note that if you use a decoder or a media recorder, you should connect the aerial cable through the
device to the television with an appropriate antenna cable, as shown in the illustrationin the following
pages.
10. PC Input is for connecting a personal computer to the TV set.
Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.
11. HDMI 2: HDMI Input
HDMI 1:12. HDMI Input
HDMI Inputs are for connecting a device that has an HDMI socket. Your LCD Television is capable of
displaying High Definition pictures from devices such as a High Definition Satellite Receiver or DVD Player.
These devices must be connected via the HDMI sockets or Component Socket. These sockets can accept
either 720p or 1080p signals. No sound connection is needed for an HDMI to HDMI connection.

English - 9 -
Viewing the Connections - Side Connectors
CI Slot is used for inserting a CI card. A CI card allows you to view all the1.
channels that you subscribe to. For more information, see “Conditional
Access” section.
Side USB input.2.
Note: Codec update cannot be performed.
Headphone jack is used for connecting an external headphone to the system.3.
Connect to the HEADPHONE jack to listen to the TV from headphones
(optional).
Video Input is used for connecting video signals of external devices.Connect4.
the video cable between the VIDEO IN socket on the TV and the VIDEO OUT
jack on your device.
Audio Inputs are used for connecting audio signals of external devices.5.
Connect the audio cable between the AUDIO INPUTS on the TV and the
AUDIO OUTPUT jacks on your device. Note: If you connect a device to the
TV via the VIDEO INPUT, you should also connect your device with an audio
cable to the AUDIO INPUTS of the TV to enable audio.
Aerial Connection
• Connect the aerial or cable TV plug to the AERIAL INPUT socket located at the rear of the TV.
Power Connection
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz.
• After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the
mains.
• Plug the power cable to the mains socket outlet.

English - 10 -
Using Digital Multimedia
Connectors
• You can connect USB devices to your TV by using
the USB input of the TV. This feature allows you to
display/play JPG and MP3 files stored in a USB
stick.
• It is possible that certain types of USB devices (e.g.
MP3 Players) may not be compatible with this TV.
• You may back up your files before making any
connections to the TV set in order to avoid any
possible data loss. Note that manufacturer will not
be responsible for any file damage or data loss.
• Do not pull out USB module while playing a file.
CAUTION: Quickly plugging and unplugging USB
devices, is a very hazardous operation. Especially,
do not repeatedly quickly plug and unplug the
drive. This may cause physical damage to the USB
player and especially the USB device itself.
SIDE VIEW USB MEMORY
USB Memory Connection
• Plug your USB device to the USB input of the TV.
IMPORTANT: The TV supports only FAT32 disk
formatting. NTFS format is not supported.
• It is recommended that you connect your USB
device directly to the USB input of the TV. Some
compatibility problems may occur if you use a
separate cable connection.
Connecting the LCD TV to a PC
For displaying your computer’s screen image on
your LCD TV, you can connect your computer to the
TV set.
• Power off both computer and display before making
any connections.
• Use 15-pin D-sub display cable to connect a PC to
the LCD TV.
• When the connection is made, switch to PC source.
See “Input selection” section.
• Set the resolution that suits your viewing requirements.
Resolution information can be found in the appendix
parts.
PC audio cable
(not supplied)
to AUDIO INPUTS
on the TV
PC RGB cable
(not supplied)
to PC input
Audio
Inputs
PC Input
Connecting to a DVD Player
If you want to connect a DVD player to your LCD
TV, you can use connectors of the TV set. DVD
players may have different connectors. Please refer
to your DVD player’s instruction book for additional
information. Power off both the TV and the device
before making any connections.
Note: Cables shown in the illustration are not
supplied.
• If your DVD player has an HDMI socket, you can
connect via HDMI. When you connect to DVD player
as illustrated below, switch to HDMI source. See,
“Input Selection” section.
• Most DVD players are connected through
COMPONENT SOCKETS. Use a component video
cable to connect video input. For enabling audio,
use a component audio cable as illustrated below.
When the connection is made, switch to YPbPr
source. See, “Input selection” section.
• You may also connect through the SCART 1 or
SCART 2. Use a SCART cable as shown below.
Note: These three methods of connection perform the
same function but in different levels of quality. It is not
necessary to connect by all three methods.
HDMI
inputs
Scart sockets
Component
video
inputs
Component
audio
inputs
DVD Player
REAR VIEW

English - 11 -
Using Side AV Connectors
You can connect a range of optional equipment
to your LCD TV. Possible connections are shown
below. Note that cables shown in the illustration are
not supplied.
• For connecting a camcorder, connect to the VIDEO
IN socket and the AUDIO SOCKETS. Do not connect
the camcoder to VIDEO IN socket at the same time
since it can cause noise in the picture. For selecting
the related source, see the section “Input selection”
in the following parts.
• To listen the TV sound from headphones, connect
to the HEADPHONE jack of theTV.
Camcorder
Headphone
Using Other Connectors
You can connect a range of optional equipment
to your LCD TV. Possible connections are shown
below. Note that cables shown in the illustration are
not supplied.
• To connect external speakers, use an audio cable.
Do not reverse the AUDIO LEFT and AUDIO RIGHT
jacks. Turn on the LCD TV and external speaker set
after all connections are made. Refer to your speaker
set’s manual for further queries.
• For connecting a to a device that has SPDIF support,
use an appropriate SPDIF cable to enable sound
connection.
External Speakers
A device that
supports
SPDIF signal.
Connecting Other Equipment via
Scart
Most devices support SCART connection. You can
connect a; DVD recorder, a VCR or a decoder to your
LCD TV by using the SCART sockets. Note that cables
shown in the illustration are not supplied.
Power off both the TV and the devices before making
any connections.
For more information, refer to your device’s own
instruction book.
Scart sockets
Decoder
DVD Recorder Video Recorder
Inserting Batteries in the Remote
Control Handset
• Remove the battery cover located on the back of
the handset by gently pulling backwards from the
indicated part.
• Insert two AAA/R3 or equivalent type batteries
inside. Observe the correct polarity (+/-) when
inserting batteries and replace the battery cover.
Note: Remove the battery from remote control
handset when it is not to be used for a long period.
Otherwise it can be damaged due to any leakage of
batteries.
Remote range is approximately 7m/23ft.

English - 12 -
Switching the TV On/Off
To Switch the TV On
• Connect the power cord to the 220-240V AC, 50
Hz.
• Press STANDBY switch. Then the standby LED
lights up.
• To switch on the TV from standby mode either:
• Press the “ ” button, P+ / P- or a numeric button
on the remote control.
• Press the -P/CH or P/CH+ button on the TV. The TV
will then switch on.
Note: If you switch on your TV via standby button on
the remote control, the programme/source that you
were watching last will be reselected.
By either method the TV will switch on.
To Switch the TV Off
• Press the “ ” button on the remote control or
press the STANDBY switch, so the TV will switch
to standby mode.
• To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active.
Input Selection
Once you have connected external systems to your
TV, you can switch to different input sources.
• Press “SOURCE” button on your remote control for
directly changing sources.
or,
• Select “Source” option from the main menu
by using “ ” or “ ” button. Use then “ ” or
“” button to highlight an input and press “ ” button
to select.
Note: You can mark desired source options by
pressing the OK button. Therefore, when “SOURCE”
button is pressed, only the marked source options will
be available (except for the TV source).
Basic Operations
You can operate your TV using both the remote
control and onset buttons.
Operation with the Buttons on the TV
Volume Setting
• Press “ ” button to decrease volume or “
” button to increase volume, so a volume level scale
(slider) will be displayed on the screen.
Programme Selection
• Press “P/CH +” button to select the next programme or
“P/CH -” button to select the previous programme.
Viewing Main Menu
• Press “ ” / “ ” buttons at the same time
to view main menu. In the Main menu select sub-
menu using “P/CH -” or “P/CH +” buttons and enter
the sub-menu using “ ” or “ ” buttons.
To learn the usage of the menus, refer to the menu
system sections.
AV Mode
• Press the “TV/AV” button in the control panel on the
TV to switch between AV modes.
Operation with the Remote Control
• The remote control of your TV is designed to control
all the functions of the model you selected. The
functions will be described in accordance with the
menu system of your TV.
• Functions of the menu system are described in the
following sections.
Volume Setting
• Press “V +” button to increase the volume. Press “V
-” button to decrease the volume. A volume level
scale (slider) will be displayed on the screen.
Programme Selection (Previous or Next
Programme)
• Press “P -” button to select the previous
programme.
• Press “P +” button to select the next programme.
Programme Selection (Direct Access)
• Press numeric buttons on the remote control to select
programmes between 0 and 9. The TV will switch
to the selected programme. To select programmes
between 10 - 299 (for IDTV) or 10-199 (for analogue),
press the numeric buttons consecutively. The limit
of the delay time is 3 seconds.
• Press directly the programme number to reselect
single digit programmes.

English - 13 -
Initial Settings
When the TV is turned on for the first time, the menu
for the language selection appears on the screen. The
message “Welcome please select your language!” is
displayed in all language options sequentially in the
On Screen Display (OSD).
By pressing the “ ” or “ ” buttons highlight the
language you want to set and press OK button. After
then, “First time installation” On Screen Display (OSD)
will appear on the screen.
By pressing “ ” or “ ” buttons, select the country
you want to set and press OK button. button (** for
EU countries).
Note: Country selection On Screen Display (OSD) will
not be available for UK.
After then, the active antenna selection On Screen
Display (OSD) appears on the screen:
By pressing “ ” or “ ” buttons, set active antenna
mode as on or off.
If an active antenna is connected to your TV, you
can select this option as On. Antenna power should
be “Off” when standard antenna is used instead of
the active antenna. See Configuration Menu in the
following sections for more information.
Press OK button on the remote control to continue
and the following message will be displayed on the
screen:
• To select the “Yes” or “No” option, highlight the
item by using “ ” or “ ” buttons and press the OK
button.
The IDTV will automatically tune to the UHF or VHF
(** for EU countries) transmission channels, searching
for digital terrestrial TV broadcasts and displaying the
names of channels found. This process will take about
a few minutes. To cancel searching, you can press the
“M” button at any time during the process.
After Automatic Search is completed, the following
message asking for analogue channel search appears
on the screen:
To search for analogue channels, select “Yes”. TV
switches to the analogue TV mode. The menu below
is displayed to search for analogue channels:
Select your Country, Language and Text language
by using “ ” or “ ” and “ ” or “ ” buttons. Press
OK or RED button to continue. To cancel, press the
BLUE button.
For more information on this process, see “Install
Menu” section.
Note: For proper functioning of digital teletext in DTV
mode, you should set country as UK in analogue
AUTO PROGRAM (for UK only).

English - 14 -
General Operation
Pressing the “TV/DTV” button at any time while
watching television programmes will switch the TV set
between the digital terrestrial television broadcasting
and its normal analogue broadcasting.
Information Banner
• Whenever you change channel, using the P- / P+
button or the numeric buttons, the TV displays the
broadcast picture along with an information banner
at the bottom of the screen (available only in DTV
mode). This will remain on the screen for a few
seconds.
• The information banner can also be displayed at any
time while watching TV by pressing the INFO button
on the remote control:
Hint: Not all channels broadcast the programme
data. If the name and time of the programme are not
available, then information banner will be displayed
with blanks.
If the selected channel is locked, you must enter the
correct four numeric code to view the channel. “Enter
PIN” will be displayed on the screen in such a case:
Electronic Programme Guide
(EPG)
• Some, but not all, channels send information about
the current and next events.
• Please note that event information is updated
automatically. If there is no event information data
available in channels, EPG will be displayed with
blanks.
• Press EPG button to view the EPG menu.
• Electronic Programme Guide appears on the screen.
It is able to get Information of the channel - programs
weekly by means of 7-DAY-EPG. All programs of
channels are displayed. On the bottom of the screen;
info bar, showing all the available commands, will
be displayed.
RED button (Shrink): makes the info boxes
smaller.
GREEN button (Expand): makes the info boxes
larger.
YELLOW button (Prev. Day): displays the
programmes of previous day.
BLUE button (Next day): displays the programmes
of the next day.
INFO (Details): displays the programmes in detail.
Numeric buttons (Jump): go to preferred channel
directly via numeric buttons.
OK : views options for future programmes.
SWAP : jumps to the current boradcast.
• Press “0” button to view Guide Search menu. Using
this feature, you can search the programme guide
database in accordance with the genre selected or
with name match.
Note: Searching process can be performed by the
desired date rate or by the channel basis.
Displaying Subtitles
With digital terrestrial broadcasting (DVB-T), some
programmes are broadcast with subtitles.
Note: You can enable subtitles by pressing the (**
for UK) or GREEN (* for EU countries)buttons.
Press the “M” button to display the main menu,
highlight the Setup and then Language menu using
“” or “ ” button and press the OK button to display
the “Language settings” menu.
Highlight the “Subtitle” item in “Language settings”
menu and use ” or “ button to set Subtitle to the
desired language.
If “Subtitle” is on and a language option is set,
pressing the TELETEXT ( ) button causes the
following warning message display on the screen (*
for UK only):

English - 15 -
Digital Teletext (** for UK only)
• Press the TELETEXT ( ) button.
• The digital teletext information appears.
• Operate it with the coloured buttons, cursor buttons
and OK button.
The operation method may differ depending on the
contents of the digital teletext.
Follow the instructions displayed on digital teletext
screen.
• When Press “SELECT” button or similar message
appears on the screen, press the OK button.
• When the TELETEXT ( ) button is pressed, the
TV returns to television broadcasting.
• With digital terrestrial broadcasting (DVB-T), in
addition to digital teletext broadcasting together with
the normal broadcasting, there are also channels
with just digital teletext broadcasting.
• The aspect ratio (picture shape) when watching
a channel with just digital teletext broadcasting is
the same as the aspect ratio of the picture viewed
previously.
• When you press the TELETEXT ( ) button again,
the digital teletext screen will be displayed.
Analogue Teletext
Use of teletext and its functions are identical to
the analogue text system. Please do refer to the
“TELETEXT” explanations.
Widescreen
Depending on the type of the broadcast being
transmitted, programmes can be viewed in a number
of formats. Press the “SCREEN” button repeatedly to
select between to change zoom mode.
When Auto is selected, the format being displayed is
determined by the picture being broadcast.
PLEASE NOTE: Menu size changes depending on
the chosen image size.
IDTV Menu System
The IDTV menu can only be viewed when watching
digital terrestrial broadcasting. Press the “
” button to turn IDTV on while the TV is in analogue
mode.
Press the “M” button. The menu below appears on
the screen:
Channel List
Using the “ ” or “ ” button on the remote control,
make sure that the first item, Channel List, is
highlighted and press the OK button to display the
Channel List.
Channel List is the place where the channels are
managed.
Navigating the Entire Channel List
Press “ ” or “ ” button for selecting the previous or
next channel. You can press P+ or P- button to move
page up or page down.
To watch a specific channel, highlight it using “ ”
or “ ” button and then press “OK” button, while the
“Select” item on Channel List menu is highlighted by
using “ ” or “ ” button.
Then the name and number of the selected channel
will be displayed in the top-left and top-right of
the channel display at the top-right of the screen,
respectively.
Moving the channels in the channel list
• Press “ ” or “ ” buttons to select the channel that
will be moved.

English - 16 -
• Press “ ” or “ ” buttons to select the “Move” item
on Channel List menu.
Note: If you enter the same programme number of the
channel that you want to move, “.... channel services
will be replaced. Do you want to continue?” On Screen
Display (OSD) will be displayed. Press OK to confirm
or select “No” to cancel.
Deleting the Channels in the Channel List
• Press “ ” or “ ” button to select the channel that
will be deleted.
• Press “ ” or “ ” button to select the “Delete’’ item
on Channel List menu.
Press the OK button to delete the highlighted channel
in the channel list. Then the message below appears
on the screen:
Press “ ” or “ ” button to highlight the desired option.
If OK button is pressed while “Yes” is highlighted, the
highlighted channel is deleted. Selecting “No” cancels
the deletion.
Renaming Channels
To rename a specific channel, the channel must
be highlighted by pressing “ ” or “ ” button. Then
highlight the Edit Name item by pressing “ ” or
“” button as illustrated below. Press the OK button
to activate the rename feature.
Now pressing “ ” or “ ” button moves to the previous/
next character. Pressing “ ” or “ ” button toggles
the current character, i.e., ‘b’ character becomes ‘a’
by “ ” and ‘c’ by “ ”. Pressing the numeric buttons
‘0...9’ replaces the highlighted character with the
characters printed above the button one by one as
the button is pressed.
Press the “M” button to cancel the editing or OK button
to save the new name.
Adding Locks to Channels
Channel locking provides a password-protected
access to channels selected by parents. In order to
lock a channel you should know the parental lock
password (default value is set to 0000 in the factory
and can only be changed from the Configuration
menu).
Select the channel to be locked by highlighting it
and select the Lock option by pressing “ ” or “ ”
button. When the OK button is pressed, a dialog On
Screen Display (OSD) asking for the password will
be displayed.
Enter the password by using the numeric buttons on
the remote control. The lock icon “ ” will now be
displayed next to the selected channel. Repeat the
same operation to cancel the lock.
Setting Favourites
To set a favourite you should highlight the “Favourites”
item at the bottom of the Channel List menu. Then
press OK button and Edit Favourite List menu appears
on the screen.

English - 17 -
How to Add a Channel to a Favourites List
• By pressing “ ” or “ ” buttons, highlight the channel
that you want to add to the favourite list.
• By pressing OK button, the highlighted channel is
added to the Favourite List.
• F icon indicates that a channel is added to Favourite
List.
Removing a Channel from Favourite List
• Highlight the channel that you want to remove from
the favourite list and press OK button to remove.You
can press OK button again to re-add a channel.
• To activate Favourites, go to the Configuration menu
and select Favourite mode. Use “ ” / “ ” to set
Favourite mode as on. To cancel Favourites, set
Favourite Mode to Off.
On Screen Help
For all menus, press the INFO/ button to display
the help information about the menu functions.
Program Guide
This section is same with the instructions given in
the General Operations page. Please see Electronic
Programme Guide (EPG) section in the General
Operations part.
Timers
To display timers window, activate the item from the
main menu. To add a timer, press the YELLOW button
on the remote control. Then “Add Timer” window
appears.
Channel: “ ” or “ ” keys will navigate the user
through the TV or Radio list.
Date: Starting date is entered via the Left/Right or the
numeric buttons.
Start: Starting time is entered via the Left/Right or
the numeric buttons.
End: Ending time is entered via the Left/Right or the
numeric buttons.
Duration: Duration between Start and End time.
Repeat: You can set a timer to be repeated as Once,
Daily or Weekly.
Change/Delete: permits or prohibits any modifications
for other users.
You can save the adjustments by pressing the GREEN
key or cancel the process by pressing the RED button.
You can edit the list via GREEN key and delete with
the RED button.
Conditional Access
• Press the Mbutton to display the main menu and use
the “ ” or “ ” button to highlight the “Conditional
Access” line and press the OK button:
Some Digital Terrestrial channels operate on a Pay
Per View basis. These require a subscription and a
hardware decoder.
Obtain the Conditional Access Module (CAM) and
the viewing card by subscribing to a pay channel
company, then insert those to the TV using the
following procedure.
• Switch off the TV and unplug from the mains.
• Insert the CAM and then the viewing card to the slot
that is located in the terminal cover at the left-hand
side of the TV (from front view).
• The CAM should be correctly inserted, it is impossible
to insert fully if reversed. The CAM or the TV terminal
may be damaged if the CAM is forcefully inserted.
• Connect the TV to the mains supply, switch on
and then wait for few moments until the card is
activated.
• Some CAMs may require the following set up. Please
set the CAM by entering the IDTV menu, Conditional
Access then pressing the OK button. (CAM set up
menu is not displayed when it is not required.)

English - 18 -
• To see the viewing contract information: enter IDTV;
press the “M” button, then highlight Conditional
Access and press the OK button.
• When no module is inserted, “No Conditional
Access module detected” message appears on
the screen.
• Refer to the module instruction manual for details
of the settings.
NOTE: Insert or remove the CI module only when the
TV is in STAND-BY mode or SWITCHED OFF.
TV Setup
You can use this item to display the TV functions.
The digital TV Setup menu screen is accessed from
the main menu. Press the “M” button to display the
main menu and use “ ” or “ ” button to highlight
“TV Setup”, press the OK button to display TV Setup
menu screen.
You can find detailed information for all menu items
in “Analogue TV Menu System” section.
Setup
The adjustments in this menu are given as the
following:
Configuration
You can configure the settings of your TV. Select
Configuration from Setup menu and press OK to view
this menu. Press the RETURN button on the remote
control to exit.
Dolby D Digital (* for EU countries only)
(Optional)
In the Configuration Menu, highlight the Dolby D
item by pressing “”or “ ” buttons. Use the “ ” or
“ ” buttons to set the Dolby D Digital as On or Off.
If the channel that you are watching supports Dolby
Digital,you can turn this setting on.
Hard of Hearing (* for EU countries only)
Use “ ” or “ ” button to select Hard of Hearing and
then press “ ” or “ ” button to set this setting as
On or Off.
If the broadcaster enables any special signal
concerning the audio, you can set this setting as On
to receive such signals.
Favourite Mode
Use this function to enable or disable favourite
mode. Press “ ” / “ ” button to set this function as
on or off.
Channel List
Use “ ” or “ ” buttons to go to Channel List option.
Use “ ” or “ ” buttons to toggle Channel List Mode.
If you select “TV Only”, with the “ ” or “ ” buttons,
you navigate through only TV channels. If you select
“Radio Only”, with the “ ” or “ ” buttons, you navigate
through only radio channels. If you select “Text Only”,
with the “ ” or “ ” buttons, you navigate through only
text channels. To save the recent changes and exit;
press the “M” button.
Active Antenna
Use “ ” or “ ” buttons to highlight Active Antenna
option.
When antenna power option is set as On by pressing
“” or “ ” button, +5V will be transmitted to the
antenna output.
This feature enables the use of active antenna.
Note: Antenna power should be “Off” when standard
antenna is used instead of the active antenna.
Scan Encrypted (**)
(**) For UK only.
Scan Encrypted Channel feature will always be ON
after performing first time installation. When this
setting is on, search process will locate the encrypted

English - 19 -
channels as well. If it is set as OFF manually, encrypted
channels will not be located while in automatic search
or manual search.
Use “ ” or “ ” button to select Scan Encrypted and
then press “ ” or “ ” button to set this setting as
On or Off.
Receiver Upgrade
Over Air Download (OAD)
To ensure that your TV always has the most update
information, use this setting. Please ensure that the TV
is set to standby mode. The TV automatically powers
up at 3.00 A.M. each day and searches for any new
information which may be broadcast and will download
this to your receiver automatically. This operation will
normally take approximately 30 minutes. If you have
an important recording to be carried out at 3.00 A.M.
and you do not want to interrupt it, disable auto OAD
search by performing the following:
• Press “M” button and using the “ ” or “ ” buttons
to choose Setup and press the OK button.
• Highlight Configuration menu with “ ” or “ ” keys
and press OK.
• Use “ ” or “ ” buttons to choose “RECEIVER
UPGRADE” and press OK button.
• Using the“ ” or “ ” button change “Automatic
scanning” from Enabled to Disabled.
• Highlight “Scan for upgrade” menu with
“” or “ ” keys and pres OK to commence
upgrade.
• After the search progress is completed, the message
“ Completed searching for upgrade. No new software
was found” appears on the screen if no new software
is found.
• Do not forget to re enable the automatic OAD
function after you have made your recording by
repeating the above instructions but this time
selecting ENABLE.
Note: Your TV may start in First Time Installation mode
after OAD update.
Parental Control
Use “ ” or “ ” buttons to go to Parental Lock option.
Press OK button to enter the menu. A dialog box
asking for the lock key will be displayed. The key
is set to “0000” initially. Enter PIN. If it is incorrect,
“Wrong Pin” On Screen Display (OSD) will be
displayed. If it is correct, the Parental Control menu
will be displayed:
Maturity Lock (**)
(**) If you set Country option as UK in the first time
installation, Maturity Lock option will not be visible.
When set, this option gets the maturity information
from the broadcast and if this maturity level is disabled,
does not show video-audio.
Menu Lock
In menu lock you can set locking for all menus, or the
Installation Menu to restrict access to these menus.
If the menu lock is disabled, there will be free access
to the menu system. Use “ ” or “ ” buttons to go to
Menu Lock option. Use “ ” or “ ” buttons to choose
Menu Lock Mode.
DISABLED : All menus are unlocked.
ALL MENUS : All Menus are accessible only with
the correct lock key. So the user cannot add, delete,
rename, channels, cannot set timers.
INSTALLATION MENU: Installation menu is locked.
So the user can’t add channels. Changes will be
updated after exiting ‘Configuration Menu’.
Set PIN
Use “ ” or “ ” buttons to go to “Set PIN” option. Press
OK to display the “Set PIN” window. Use numeric
buttons to enter new pin number you will need to
input your new pin a second time for verification
purposes. The factory default pin number is 0000,
if you change the pin number make sure you write it
down and keep it safe.
Time Settings (**)
(**) If you set Country option as UK in the first time
installation, Time Settings option will not be visible.
In the configuration menu, highlight the Time Settings
item by pressing “ ” or “ ” buttons. Press OK and
Time Settings sub menu will be displayed on the