Techone 1300 Popwing User manual

1. These EPP flying wings are very popular for
outdoor flying.
2. Made of high quality EPP material, it is very
durable and easy to fly.
3. Most of the parts are pre-assembled in our
factory, for you it’s very easy to build.
Fuselage length: 390MM (15.3in.)
Wingspan: 1300MM (51.1in.)
Flying Weight:484g (with battery)
Motor: AS2216 KV 1250
ESC: 30 Amp
Propeller: 9*5 or 9047 sf
Servo: 10-17g micro servo*4pcs
Radio: 4/more channel
Battery: 11.1V1800mAh Li-po 25C
Wind strong enough to make the trees rustle
A street with many trees or street lamps
Close to high voltage electrical wires
High Population density areas
Cautions for flying
Large gyms, front lawns and parks make
excellent flying areas. Make sure you
have permission to fly and follow safety
guidelines set by local authorities.
The calmer the wind, the better!
Note for Storage
Please disconnect the lipo packs when
finished flying
Do not press or crush the airplane when
storing
The best way to store is to hang the airplane
to keep the control surface rigid
Recommended Flying Setup
Max servo travel of aileron: 40degrees up
and 40degrees down(28mm)
Max servo travel of elevator:50 degrees up
and 50 degrees down(28mm)
235-245mm away from the nose
235-245mm

1.Wing
2.Wing fences
3.Skid
4.Motor mount
5.Reinforcement for wing connecting
square tube
6.Battery fixing board
7.Wing reinforcing carbon fiber rod
8.Nylon strap
9.Push rod with Z bend
10.Wing connecting square tube
11.Glass fiber control horn
12.Adjustor
13.Motor fixing screws
Assembly steps
Fix the left and right wing with glue.
Insert the wing connecting square tube into
the pre-reserved slot and fix with glue.
Reinforcement for wing connecting square tube
1
1
2
3
3
1pc
2pcs
1pc
1pc
2pcs
1pc
2pcs
2pcs
2pcs
1pc
2pcs
2pcs
4pcs
3

Motor mount
Install the motor mount on corresponding
place in above picture with glue. Please align
the round holes at the central line of the airframe.
Battery fixing board
Put the battery fixing board on the bottom of
wing, then fix with glue.
Find 4 burned holes on top and bottom wing
(2 holes each).
Cut a slot along the 2 burned holes on top of
wing.
Cut another slot along the 2 burned holes on
bottom of wing.
4
4
5
5
6
6
7
Prepare 2pcs carbon rods.(
carbon fiber rod)Wing reinforcing
Insert the carbon rods into slots on both sides
of wing, then fix with glue.
8
8

Put the skid on the central line which is near the
nose and fix with glue.
The pointed position in black is the adhesive
position of wing fence and the lower arc line of
the wing. (The burned holes can be seen clearly
on the wing fences)
Align the two burned holes with lower arc line
of wing as picture shown, then fix with glue.
9
9
10
10
10
10
Tighten the screw after finishing the
installation of the servo and servo arm.
The completion of the servo arm installation
11
11
12

Place servo into the pre-reserved servo house
and fix with glue.
Cut a slot for embeding the servo wire.
Embed the servo wire into the slot.
Glass fiber control horn and adjustor
Use the reamer to enlarge the aperture to fit
the adjustor.
12
13
14
15
15
Fix the adjustor and control horn with glue as
picture shown.
Cut a slot for installing the glass fiber control
horn as picture shown.
16
16
17
Put the control horn into the slot and fix with
glue.
18

Connect the servo and control horn with
Z bend push rod.
Cut off the redundant wire with pliers.
Tighten the screw of adjustor after make
sure the control surface and wing is in the
same level.
The completion picture after installation of the
servo and push rod.
19
20
21
22
Motor fixing screws
Install motor on motor mount with screws.
Propeller.
Install the propeller on motor shaft.
23
23
23
24
24

7
Then put the washer on propeller as picture
shown.
Screw down the bullet head.
The planform of the installed motor and propeller.
Make sure the motor and propeller is in neutral.
ESC 30A
25
26
26
27
Connect motor and ESC wire.
Nylon strap
Thread nylon straps through the equipment
cabin.
Put ESC inside the equipment cabin as picture
shown.
27
28
28
28

8
Receiver
Plug the equipment connectors into
corresponding receiver holes.
Tighten the nylon straps after placed all
equipments neatly.
Cut off redundant part with pliers.
29
29
30
31
Battery 11.1V 1800MAH 3S
Put the battery into battery house.
Fix battery with velcro strap.
32
32
32
The completion of the airplane.
A perfect 1300 Popwing-EPP is done after your
careful assembly. While assembly, the flying
weight is really critical to the flight performance
and will be affected by adding weight, so you
should reduce any unnecessary weight while
assembly. Then you’ll get the best flying
performance.