TECHWOOD TBLC-951 User manual

1
ELECTRIC BLENDER & SOUP MAKER
Instruction manual
Dear consumer,
Please read these instructions carefully before use in order to avoid
damage due to incorrect use and to better understand the functions of this
product. Please pay particular attention to the safety guide.
If you pass the device on to a third party, these Operating Instructions
must also be handed over.
Please keep them for future references.
TBLC-951
TBLC-956
TBLC-951
TBLC-956

2
IMPORTANT SAFEGUARDS
Please read these instructions carefully before use.
Keep present instructions for future references.
Check that your mains voltage corresponds to that stated on
the appliance.
Only use the appliance for domestic purposes and household
or similar applications such as:
-staff kitchen areas, in shops, offices and other working
environments;
-by clients in hotels, motels and other residential type
environments;
- Environment type like :
• Farm Houses • Bed and Breakfast.
Only use the appliance in the way indicated in these
instructions.
Never use this unit near bathtub, shower, wash-hand basins
or other containers with water.
Never use this apparatus near water projections.
Never use this apparatus with the wet hands.
If, unfortunately the apparatus is wet, immediately withdraw
the cord of the socket-outlet.
Inform potential users of these instructions.
Never leave the appliance unsupervised when in use.
The appliance must be used only for its intended purpose. No
responsibility can be taken for any possible damage or injury
caused by incorrect use or improper handling.
Children and persons with disabilities are not always aware of
the danger posed by the use of appliances.
This appliance can be used by persons with reduced
physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and
if they understand the hazards involved.

3
Always disconnect the appliance from the supply if it is left
unattended and before assembling, disassembling or
cleaning
This appliance shall not be used by children. Keep the
appliance and its cord out of reach of children
Regarding the instructions for cleaning surfaces in contact
with food or oil, thanks to refer to the below paragraph
"cleaning and maintenance" in manual.
Regarding the instructions for the use of accessories,
operation times and speed settings, thanks to refer to the
below paragraphs.
Care shall be taken when handling the sharp cutting blades,
emptying the bowl and during cleaning
This device is not a toy, do not leave children or people with
disabilities to play with.
In order to ensure your children‘s safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
Caution ! Do not allow small children to play with the foil :
THERE IS A DANGER OF SUFFOCATION !
From time to time check the cord for damages. Never use the
appliance if cord or appliance shows any signs of damage.
Never immerse the appliance in water or any other liquid for
any reason whatsoever.
Never place it into the dishwasher.
Never use the appliance near hot surfaces.
Do not operate the appliance with a damaged cord or plug, or
after the appliance has been damaged in any manner. If the
supply cord or appliance is damaged, it must be replaced by
the manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Disconnect the power source cable before any operation of
cleaning of maintenance and accessories assembly.
Never use the appliance outside and always place it in a dry
environment.

4
Never use accessories, which are not recommended by the
producer. They could constitute a danger to the user and risk
to damage the appliance.
Never use any other connector than the one provided.
Never move the appliance by pulling the cord. Make sure the
cord cannot get caught in any way.
Never wind the cord around the appliance and do not bend it
Ensure that the power cord does not come into contact with
hot parts of this unit.
Make sure the appliance has cooled down before cleaning
and storing it.
The temperature of accessible surfaces may be very high
when the appliance is operating. Never touch these parts, of
apparatus, to avoid burning itself.
Make sure the appliance never comes into contact with
flammable materials, such as curtains, cloth, etc...& the
power cord and plug do not come in contact with water.
Before cleaning, always unplug the appliance from the power
supply and let it cool down.
This appliance is not intended to be operated by means of an
external timer or separate remote-control system.
Always place the unit on a flat surface. Ensure, also, not to
cover the device and not to put anything on it.
Always remove the plug from the wall socket when the
appliance is not in use.
When using an extension lead always make sure that the
entire cable is unwound from the reel. Use solely CE
approved extension leads. Input power must be at least 16A,
250V, 3000W.
Incorrect operation and improper use can damage the
appliance and cause injury to the user.
This device, designed for home use, complies with standards
relating to this type of product.
The appliance must be used and rested on a table or flat &
stable surface.

5
The item must not be left unattended when it is connected to
main supply.
The item is not to be used, if it has been dropped or if there
are visible signs of damage or if it is leaking.
This appliance is only intended for household use.
SPECIAL WARNING FOR BLENDER
Switch off the appliance and disconnect from supply before
changing accessories approaching parts that move in use.
Potential injuries can occur with misuse. Care shall be taken
when handling the sharp cutting blades, emptying the bowl
and during cleaning, as they are extremely sharp.
Regarding the instructions for cleaning surfaces in contact
with food or oil, thanks to refer to the below paragraph
"cleaning and maintenance" in manual.
Regarding the instructions for the use of accessories,
operation times and speed settings, refer to the below
paragraphs.
The blades are sharp. Take all necessary precautions.
To mix liquids, especially hot liquids, it is advisable to proceed
in small quantities, at the same time, to avoid overflowing.
Never fill above half of the bowl.
Do not leave cooking utensils in the container during mixing
and even only when the appliance is not in use.
Never use products or liquids hotter than 80 ° C (or 127 ° F)
After a maximum of 3 minutes, the blender should cool for at
least one minute to avoid overheating.
Repairs must only be carried out by an authorized repairer.
THIS PRODUCT IS INTENDED FOR PRIVATE HOUSE USE
ONLY.

6
GENERAL INFORMATION
The symbol "OPEN BOOK" means a recommendation
to read important things contained in the record.
The symbol "BIN" crossed out, abbreviation WEEE
(Waste of Electrical and Electronic Equipment) means
that at the end of life, it should not be discarded with
household waste, but filed to the sorting of the locality.
Waste recovery can help preserve our environment.
The symbol "CE" is the guarantee of compliance with
harmonized European standards, voluntary, reflecting
the essential requirements into technical
specifications. These standards are not mandatory
but are guarantees of compliance with essential
requirements.
The symbol ROHS (Restriction of use of some
Hazardous Substances) on the Environmental
Protection, certifies that for each of the five hazardous
substances • Lead • Mercury • (hexavalent) chromium •
products for protection against flames PBB and PBDE,
the peak concentration is equal to or less than 0.1% of
the weight of homogeneous material, and 0.01% for the
6th • cadmium.
The symbol "GLASS / FORK" means that the device
is compatible and can come into contact with
foodstuffs.
The symbol "TRIMAN" indicates that the consumer is
invited to dispose the product as part of a separate
collection (eg recycling bin, waste, voluntary intake
point).

7
For more information : http://www.quefairedemesdechets.fr
FIRST USE
Before first use, remove the unit and all accessories carefully and paying attention
to the sharp accessories.
Clean with soap and water, bowls and all accessories. Rinse and dry thoroughly.
Clean the outside and inside of the machine cabinet with a damp cloth and wipe
dry.
Do not immerse the device in water or any other liquid.
Place the machine on a suitable flat, stable surface.
TO KNOW THE APPLIANCE
The blades of the soup maker can be used solely as a blender to make
smoothies, purees, dips and dressings …
The soup maker is fitted with several safety features
A sensor on the lid.
A sensor for the minimum level of liquid.
A heat sensor for safe use.
Cut-off safety on the motor base. (if the bowl is not properly engaged).
1 Lid
2 Jug
3 Stainless Steel Knife
4 Hot Plate
5 Base
6 Handle
7 Blending Button
8 Timer

8
USE
Unroll the power cord completely.
Check that the tension in force in the country where you are, corresponds to
that indicated on the apparatus.
Connect the apparatus in a correct socket-outlet, (and connected to the
ground if the unit is Class I), to avoid any danger.
Disconnect the power source cable before any operation of cleaning of
maintenance and accessories assembly.
Never modify the appliance in anyway.
Warning : the bowl contains very sharp and sharp blades, it must be handled with
care.
Place the unit on a stable, heat-resistant surface.
Carefully place the carafe on its base while aligning the safety points.
Connections between the base of the handle and the base unit.
The bowl of the blender should be properly seated in its location on the base.
Place the lid on the heating blender by aligning the lid lock with the bowl
handle, and push down on the lid (with a little force) until you hear a locking
"click".
When everything is properly assembled, connect the unit to the main power
supply and press the mix button (7) to test.
Note: If the blender starts, it means that the assembly of parts is well done.
Remove the cover.
Put some water and ingredients in the bowl.
Note: Not less than the minimum level and not more than the maximum level.
Close the lid, place the bowl on the base.
Set the timer to the desired cooking time.
the blue indicator light will come on, and the blender will begin to heat up.
When the mixture is hot, press the Blender button (7) to mix the ingredients,
release the button when the mixture is sufficient. This will stop the blender.
Wait for the cutting blade to stop completely before removing the cover to avoid
splashing.
1. making soup
chop all your ingredients into approximately 2-3cm cubes and add to the soup
maker jug.
Notes : it is not recommended to use uncooked meat or fish in the soup maker.
Any meat or fish used in this soup maker must be precooked.
Do not add any frozen ingredients.
All ingredients must be room temperature.

9
It is possible to add, in place of water, juice or broth or other edible liquid.
All liquids used must also be at room temperature.
Make sure the total volume of ingredients added is above the minimum but not
more than 1700ml,
Notes : the internal sensor near the base of the jug must be covered with liquid.
Under filling the soup maker jug will result in the alarm sounding and the
unit fail to operate,
Should the boiling action during cooking cause the contents to reach the
lid, the upper sensor will switch off the heating function to help prevent
boiling over.
Avoid starch and sugar. They can burn the bottom of the blender bowl.
Any interruption will result in the cancellation of the program, the restart
will result in the cooking steps already performed that may affect the
final recipe.
The cooking time must be maximum 25 to 30 minutes.
To completely stop the program, just set the timer to “zero”.
Note : Once the cooking is finished, the pilot indicator will light off and an audible
sound will be eared.
After cooking, mix the ingredients by pressing the blender button (7).
Press longer to obtain a velvety.
WARNING
Be careful when opening the lid because it will be hot.
Steam can also be released.
Never touch the surface of the lid because it is very hot after use.
Always use the small handle provided for this purpose.
1. Rotate the lid by pressing
counter-clockwise the small handle.
2. Hold the handle of the blender
with one hand and remove the lid
with the small handle with the other
hand.
Example on the right :

10
2. Reheating
Previously prepared soup that has gone cold can be reheated in the soup maker.
Set the timer time according to your wish.
3. Blending
The heated Blender is also a traditional Blender.
Just assemble the device, add the ingredients and mix.
Notes : It is important that the ingredients reach the minimum level in the bowl, but
does not exceed the maximum level.
It is impossible to grind the dry ingredients. The sensor will not accept it.
CLEANING AND MAINTENANCE
Before cleaning, Always : switch off the appliance, disconnect the apparatus and
let it cool.
Clean the outside of the apparatus with a sponge or slightly wet linen.
The parts (removable) in contact with food like plate, bowl, forks, Spatula etc. can
be washed in hot water with sponge and soft detergent or put in the dishwasher
(except elements with connector).
Never plunge the apparatus in water or all other liquid !
Do not use abrasive cleaners, gritting, or metal brush or another cutting object.
Do not clean the soup maker in dish washer.
Always disconnect the soup maker before cleaning.
Do not immerse the soup maker in water or any liquids.
Rinse the lid in warm, soupy water.
To clean the inside of the jug, rinse to remove any soup or large food particles.
Remove any food remains using a soft cloth and mild detergent before rinsing
again.
Caution: the blades in the jug are very sharp and removable, extreme caution
shall be taken when cleaning the inside of the jug.
Tip for Cleaning the jug.
Pour 800ml of water, press the blending button to clean the jug, release the button
to stop the process.
Change the water and start again if necessary.

11
Trouble shooting
Problems
Solutions
The unit is not working and beeping
1. the jug is not fitted to the base well.
2. the lid is not locked well.
3. there is no enough liquid in the jug.
4. there are spills around overflow-
sensor
The unit has stopped in the middle of
cooking
1. the lid is loose
2. liquid becomes too low
3. liquid is too much than the maximum
sendor level.
4. the jug is loose connect to the base.
Food is not blended
1. pieces were too large.
2. food was not boiled before blending.
3. too much water.
Food was not cooked well
1. chop the food into smaller pieces
before adding.
2. some food required longer cooking
time
Soup is not boiled
Too much soup, the liquid reaches the
maximum sensor and heating stopped
Food is burnt and stuck to the bottom
1. caused by high sugar, starch; use
proper sugar, starch.
2. too much food and too little liquids.
STORAGE
-Ensure the unit is completely cool and dry.
-Do not wrap the cord around the appliance, as this will cause damage.
-Keep the appliance in a cool, dry place and out of reach from children.
GUARANTEE
Before being delivered, all our products are subjected to a rigorous control.
This apparatus is guaranteed 24 months starting from the date of purchase by the
consumer.
The documents in proof of guarantee are:
• The invoice and
• The filled and stamped warrantee plate (located on side or bottom of the gift
box). Without these documents in proof, no free replacement, nor no free repair,
can be carried out.
During the warranty period, we deal for free, the defects of the apparatus or the
accessories, rising from a defect of materials or manufacture by repair or,

12
replacement. The services within the framework of the guarantee do not involve
any extension of the warranty period and does not give right to a new guarantee!
In the event of recourse to the guarantee, bring back the complete apparatus to
your retailer, in its original packing, accompanied by the proofs of purchase.
The breakage of parts out of glass or plastic is, in all the cases, not warranted.
Defects on the accessories or the wearing parts (for example: coals of engines,
hooks, drive belts, remote control of replacement, teeth brushes of replacement,
webs etc) as well as cleaning, maintenance or it replacement of wearing parts are
not guaranteed and are thus to pay!
In the event of foreign intervention, the guarantee becomes null and void.
After flow of the warranty period, repairs can be carried out, against payment, by a
specialized trade or a repair service.
SPECIFICATIONS
Power supply 220-240V~ 50/60Hz
Power 900-1100W
Timer 60 Minutes
Capacity 1,5L
Norm Class I
Made in PRC
The characteristics can change without prior notice.
This device complies with EC directives, it was controlled according to all current
European directives, applicable such as: electromagnetic compatibility (EMC) and
low voltage (LVD).
This device has been designed and manufactured in compliance with the latest
regulations and technical requirements for safety.
This unit is equipped with an electrical outlet with earth and must be
earthed in an according plug.
Note : In the event of question concerning the earth or electric
connection, please consult a qualified personnel.
In the event of short-circuit, earthing reduces the risk of electric
shock while making possible the current to be evacuated by the wire
of ground.
CAUTION: In order to minimize the risks of electric shock, In the event of
breakdown, not to open the case but to call upon a qualified technician
for repairs.
Imported by Sotech International
" LE PERIPOLE " N°A-107
33, Avenue du Marechal de Lattre de Tassigny
94120 Fontenay sous-bois - France