TECHWOOD TCO-6025 User manual


“WET & DRY” RECHARGEABLE RAZOR
+ small Trimmer + Pouch
INSTRUCTION
MANUAL

1

IMPORTANT SAFEGUARDS
❑The appliance is only to be used with the power supply unit
provided with the appliance.
❑Please read these instructions carefully before use.
❑Keep present instructions for future references.
❑Check that your mains voltage corresponds to that stated on
the appliance.
❑Only use the appliance for domestic purposes and household
or similar applications such as:
- staff kitchen areas, in shops, offices and other working
environments;
- By clients in hotels, motels and other residential type
environments;
- Environment type like :
• Farm Houses • Bed and Breakfast.
❑Only use the appliance in the way indicated in these
instructions.
❑Never use this unit near bathtub, shower, wash-hand basins or
other containers with water.
❑Never use this apparatus near water projections.
❑Never use this apparatus with the wet hands.
❑If, unfortunately the apparatus is wet, immediately withdraw the
cord of the socket-outlet.
❑Inform potential users of these instructions.
❑Never leave the appliance unsupervised when in use.
❑The appliance must be used only for its intended purpose. No
responsibility can be taken for any possible damage caused by
incorrect use or improper handling.
❑Children and persons with disabilities are not always aware of
the danger posed by the use of appliances.
2

❑The appliance can be used by children aged from 3 years
under supervision.
❑This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
❑Children shall not play with the appliance.
❑Cleaning and user maintenance shall not be made by children
without supervision.
❑In order to ensure your children‘s safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
❑Caution ! Do not allow small children to play with the foil :
THERE IS A DANGER OF SUFFOCATION !
❑From time to time check the cord for damages. Never use the
appliance if cord or appliance shows any signs of damage.
❑Never immerse the appliance in water or any other liquid for
any reason whatsoever.
❑Never place it into the dishwasher.
❑Never use the appliance near hot surfaces.
❑Do not operate the appliance with a damaged cord or plug, or
after the appliance has been damaged in any manner.
❑Disconnect the power source cable before any operation of
cleaning of maintenance and accessories assembly.
❑Never use the appliance outside and always place it in a dry
environment.
❑Never use accessories, which are not recommended by the
producer. They could constitute a danger to the user and risk to
damage the appliance.
❑Never use any other connector than the one provided.
3

❑Never move the appliance by pulling the cord. Make sure the
cord cannot get caught in any way.
❑Never wind the cord around the appliance and do not bend it
❑Ensure that the power cord does not come into contact with hot
parts of this unit.
❑The device must be operated only under the very low safety
voltage corresponding to the marking of the device.
❑Make sure the appliance has cooled down before cleaning and
storing it.
❑The temperature of accessible surfaces may be very high when
the appliance is operating. Never touch these parts, of
apparatus, to avoid burning itself.
❑Make sure the appliance never comes into contact with
flammable materials, such as curtains, cloth, etc... & the power
cord and plug do not come in contact with water.
❑Before cleaning, always unplug the appliance from the power
supply and let it cool down.
❑This appliance is not intended to be operated by means of an
external timer or separate remote-control system.
❑Always place the unit on a flat surface. Ensure, also, not to
cover the device and not to put anything on it.
❑Always remove the plug from the wall socket when the
appliance is not in use.
❑When using an extension lead always make sure that the entire
cable is unwound from the reel. Use solely CE approved
extension leads. Input power must be at least 16A, 250V,
3000W.
❑Incorrect operation and improper use can damage the appliance
and cause injury to the user.
❑This device, designed for home use, complies with standards
relating to this type of product.
4

❑The appliance must be used and rested on a table or flat &
stable surface.
❑The item must not be left unattended when it is connected to
main supply.
❑The item is not to be used, if it has been dropped or if there are
visible signs of damage or if it is leaking.
❑Regarding the instructions for cleaning, thanks to refer to the
below paragraph of the manual.
❑This appliance is only intended for household use.
GENERAL INFORMATION
The symbol "OPEN BOOK" means a recommendation to
read important things contained in the record.
The symbol "BIN" crossed out, abbreviation WEEE
(Waste of Electrical and Electronic Equipment) means
that at the end of life, it should not be discarded with
household waste, but filed to the sorting of the locality.
Waste recovery can help preserve our environment.
The symbol "CE" is the guarantee of compliance with
harmonized European standards, voluntary, reflecting
the essential requirements into technical specifications.
These standards are not mandatory but are guarantees
of compliance with essential requirements.
The symbol ROHS (Restriction of use of some Hazardous
Substances) on the Environmental Protection, certifies
that for each of the five hazardous substances • Lead •
Mercury • (hexavalent) chromium • products for
5

protection against flames PBB and PBDE, the peak
concentration is equal to or less than 0.1% of the weight
of homogeneous material, and 0.01% for the 6th •
cadmium.
The symbol "III" means that the equipment concerned is
designed to be supplied at a voltage of not more than
50 volts AC or 120 volts DC. Materials with this sign are
classified as Class III.
The symbol "TRIMAN" indicates that the consumer is
invited to dispose the product as part of a separate
collection (eg recycling bin, waste, voluntary intake
point).
For more information : http://www.quefairedemesdechets.fr
PARTICULAR WARNING FOR PRODUCT
USED IN A BATHROOM
● Switch off when not in use, even if for a moment.
● Unplug it after use, since the proximity of water presents a
hazard, even when the unit is switched off.
• When the unit is used in a bathroom unplug it after use since the
proximity of water presents a risk, even when the power is off.
● To provide additional protection, in the electrical circuit
supplying the bathroom, a residual current device (RCD) with a
rated residual current not exceeding 30mA operation, is
recommended. Consult your installer.
NOTE: A thermal fuse, is not a residual current device (RCD).
6

• Do not use this product while taking a shower or bath.
• Always unplug the unit itself between two closely spaced uses.
• For example: Stop the machine and unplug it if you drop it while
you dry.
USE
● Unroll the power cord completely for charging.
● Check that the tension in force in the country where you are corresponds to that
indicated on the apparatus.
● Disconnect the power source cable before any operation of cleaning of
maintenance and accessories assembly.
● Stand the appliance on a table or flat surface.
● Never modify the appliance in anyway.
How to use
Dry ? Under the shower ? In the tub ?
With your new Lady Shave you cue remove unwanted hair quickly, simply
andcomfortably, at home or "on the move".
According to your own preference, you can use the appliance either "dry" orwhile
taking a shower !
Many users like to lather the skin with shampoo, soap or shaving foam before
use.When ready, you can simply rinse the appliance, clean under the shower or tap.
Charging
The appliance is designed for cordless use only
And it is charged via the charge unit.
Before using the appliance for the first time, or if it has not
been used for aconsiderable time, it should be charged for 8 h.
A full charge is sufficient +/- 30 minutes, if normally used.
The unit charger must be placed on a horizontal surface. Select a spot close toa well
socket where the charge unit cannot fall into water.
Keep the charge unit connected to mains power and always replace the
applianceinto it after use to recharge.
Note: Always charge the shaver after wiping it properly after use (if wet).
Always switch off before placing the appliance into thecharge unit,
7

1. Place the trimmer and the shaving foil gently on the skin.
2. Move the lady shave slowly and with light pressure over the skin.
3. For best results direct the shaver head against the direction of the hair growth.
After use
1. Stop the unit by sliding the switch down.
2. Put the razor on its base.
3. Replace the cover on the unit head.
CLEANING AND MAINTENANCE
1. Remove the shaver from its charger base for cleaning.
Notes : Make sure the unit is off and unplugged from the mains.
Do not apply any pressure on the razor's head to preserve it.
2. Do not use acetone, gasoline and abrasive material, wire brush or other sharp
objects on plastic parts.
3. Clean the device after each use.
4. Do not rinse the shaver with hot water (maximum 35°C)
8

Note: It is not necessary to disassemble the head after each use.
Only shake the razor, blow and brush the remaining hairs.
5. Clean the outside of the appliance with a sponge or slightly damp cloth.
Twice a year, drop a drop of oil (Oil for sewing machine or oil for hair clipper) on the
razor's head and the precision mower.
Head Replacement
• It you use the appliance twice a week or more, it is admissible to replace the
shavinghead unit every one or two years.
• A worn-out or damaged shaving toil can be replaced only with the original
shavingtoil unit type.
For that, contact your store or an after-sales service.
STORAGE
-Ensure the unit is completely cool and dry.
-Do not wrap the cord around the appliance, as this will cause damage.
-Keep the appliance in a cool, dry place.
GUARANTEE
Before being delivered, all our products are subjected to a rigorous control.
This apparatus is guaranteed 24 months starting from the date of purchase by the
consumer.
The documents in proof of guarantee are :
• The invoice and
• The filled and stamped warrantee plate (located on side or bottom of the gift box).
Without these documents in proof, no free replacement, nor no free repair, can be
carried out.
During the warranty period, we deal for free, the defects of the apparatus or the
accessories, rising from a defect of materials or manufacture by repair or,
9

replacement. The services within the framework of the guarantee do not involve any
extension of the warranty period and does not give right to a new guarantee !
In the event of recourse to the guarantee, bring back the complete apparatus to your
retailer, in its original packing, accompanied by the proofs of purchase.
The breakage of parts out of glass or plastic is, in all the cases, not warranted.
Defects on the accessories or the wearing parts (for example: coals of engines,
hooks, drive belts, remote control of replacement, teeth brushes of replacement,
webs etc) as well as cleaning, maintenance or it replacement of wearing parts are
not guaranteed and are thus to pay !
In the event of foreign intervention, the guarantee becomes null and void.
After flow of the warranty period, repairs can be carried out, against payment, by a
specialized trade or a repair service.
Troubleshooting
Reduced shaving performance
Cause 1: The shaving heed in dirty.
a remove the foil
b remove the cutter unit & rinse both under the tap
c Make sure that no hairs are stuck under the trimmer !
Cause 2: Shaving heed works rather slowly (shaver sounds "weak")
a charge the shaver
b clean the shaving heed
c lubricate the shaving head with some drupe of sewing machine oil More skin
irritation than usual
d Replace the shaving foil, as it is damaged or worn.
Appliance doesn't work
Cause 1: The rechargeable battery in empty.
a Recharge the buttery
Appliance doesn't charge
Cause 1: Charging unit in not plugged in
Cause 2: Appliance has not been placed properly in the charging unit.
10

a Put the appliance in the charging unit in such a way that you hear a click (to
indicatethat the shaver has been placed properly in the charging unit) and the red
pilot lightgoes on (to indicate that the appliance in charging)
Cause 3: The red pilot light in on, but the appliance in still not charging.
a Switch the appliance off by setting the slide to off and charge theappliance.
SPECIFICATIONS
LADY SHAVER
Power supply 1 rechargeable Battery AA
1,2V DC / 3W
Norm Class III
Operating 3V DC 200mA
Charging time 8H
Using time +/- 30 Minutes
AC ADAPTER
Power supply INPUT 100-240V~50/60Hz 80mA
OUTPUT 3V DC / 200 mA
Norm Class II
Made in P.R.C
The characteristics can change without prior notice.
ENVIRONMENTAL PROTECTION
(Destruction of batteries)
To remove the battery:
• Open the battery compartment and retrieve the battery or batteries.
- BATTERY CONTAINS NICKEL CADMIUM AND / OR LITHIUM AND / OR
NICKEL-METAL HYDRIDE, THE BATTERY MUST BE ELIMINATED IN A SAFE
WAY.
DO NOT THROW IN A TRASH CAN, BUT GIVE IN CENTRE OF WASTE.
that the device can be used on the skin or human orifices. (Example:
Thermometer).
11

CAUTION: In order to minimize the risks of electric shock, In the event
of breakdown, not to open the case but to call upon a qualified
technician for repairs.
This device complies with EC directives, it was controlled according to all current
European directives, applicable such as: electromagnetic compatibility (EMC) and
low voltage (LVD).
This device has been designed and manufactured in compliance with the latest
regulations and technical requirements for safety.
FACIAL TRIMMER
IDEAL FOR :
Bikini area, Neck, Eyebrows and all unsightly hair ...
Not to be used as a shaver.
Before cleaning head, make sure that the switch is on OFF position.
Be careful not to over trim at the same place or in the same skin eria.
Use with caution when near eyes.
Do not use on eyelashes.
For external use only.
PARTS
1 CLEANING BRUSH
2 MAIN UNIT
3 HEAD CAP
4 BATTERY COVER
5 EYEBROWS PROTECTION
BATTERY
Use 1 x AAA" or LR3 battery. (Not provided)
I. Remove cap
Note : Make sure unitis in the OFF position
2 Remove the battery compartment cover.
3 Insert the battery (respecting the direction of polarity)
4 Replace & Close the compartment cover.
WARNING: If the unit does not workverify if the battery is correctly inserted.
Using unit with main head
12

I. Turn unit on by pushing the ON/OFF switch upward in the direction of arrow
2. Gently, Place the head against the hair to be removed.
3. Move in an upward direction against the growth ofhair to be removed.
Note: Use for all designated areasof the body
Attaching Eyebrow Trimming Guard
Note: Try long side first to determineappropriate side of attachment. If the long side
is not performing then try the short side. We recommend always testing the long side
first.
I. Make sure the unit is in the OFF position.
2. Race fingers on the neck of the main unit
3. Attach guard over main bead, push downand snap into place.
Using The Eyebrow Trimmer Guard :
I. Attach guard to unit.
2. Turn unit ON.
3. Comb, following the natural shape of the eyebrowstarting at the widest end to the
thinnest.
Important For thick and bushy eyebrows you mayhave a to repeat step 3 until
desired result is achieved.
CARE AND MAINTENANCE
To Clean Eyebrow Trimming Guard
I. Remove guard end use cleaning brush to remove hairsfrom the teeth.
2. Wash with soapy water if necessary
3. Make sure guard is completely dry before attaching tomain unit
To Clean Main Head Attachment
Use cleaning brush provided to remove any hairs
I. Make sure unit is in the OFF position.
2. Turn to the backside of the unit (This side is the opposite side of thepower switch).
3. Push lock down to unlock main head
Note: Main headshould pop off from main unit.
13

4. Pull head down and remove frommain unit
5. Remove hairs with cleaning brush
6. Replace head by inserting theprotruding edge into the opening on the top of the
head
Note: Do not force head into place.
7. Snap into place and secure by pushing the lock button up until it clicks and
lockshead in place.
Power supply : 1 x 1,5V LR3 or AAA battery (not provided)
Imported by Sotech International
" LE PERIPOLE " N°A-107
33, Avenue du Marechal de Lattre de Tassigny
94120 Fontenay sous bois - France
14