TECNOEKA KF 981 User manual

USE AND INSTRUCTION MANUAL
MOD. KF 981 – KF 981 UD
rev. 0
TECNOEKA S.r.l.
Via I. Nievo, n.12/B - 35012 Camposampiero (Padova) Italy
Tel. [phone] Fax [phone]
www.tecnoeka.com E-mail: [email protected]

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 2 _________________________________________________________________________________________
\\Ekaserver\Dati\Sistema Gestione Qualità (SGQ)\PRODOTTI\Famiglia 1 - FORNI\FORNO
ELETTRICO 40 60 90\LEka\MANUALI D'USO - Forno Elettrico 40 60 90 - LEka\Manuale d'uso
KF 981 - KF 981 UD - GB rev. 0.doc

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 3 _
Prodotti mirati per Ristorazioni, Pasticcerie,
Panetterie e Gastronomie
TECNOEKA Srl
Via I. Nievo, 12/B
35012 Camposampiero (PD)
Tel. [phone]
Fax + 39 049 5794387
www.tecnoeka.com – [email protected]
CE DECLARATION OF CONFORMITY
Annexed document II A, of directive 98/37/EC
Manufacturer TECNOEKA Srl
Address Via I. Nievo, 12/B - 35012 Camposampiero (Pd)
Type of product Electric oven
Model KF 981 - KF 981 UD
TECNOEKA Srl declares that the above mentioned products conform to the safety
regulations under:
CEI EN 60335-1
- Low voltage directive 2006/95/EC CEI EN 60335-2-42
CEI EN 55014-1
CEI EN 61000-3-2
- Electromagnetic compatibility Directive 2004/108/EC
CEI EN 61000-3-3
- Machine Directive 98/37/EC;
- Directive on the general safety of products 2001/95/EC;
- Directive on the restriction in the use of dangerous substances in electrical
and electronic appliances 2002/95/EC;
- Directive on waste from electrical and electronic appliances 2002/96/EC.
Camposampiero, 06/12/2007.
_________________________________
Signature of a Representative of the Board of
directors

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 4 _________________________________________________________________________________________

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 5 _
Index
1. Technical service
2. General warnings
3. Technical specifications
4. Instructions for the installer
5. Use instructions (for the user)
6. Residual risks (for the user)
7. How to use the control panel
8. Oven cooking
9. Cleaning
10. Maintenance
11. Technical service
12. Informations to the consumers
13. Wiring layout
14. The Warranty

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 6 _________________________________________________________________________________________
1. Technical service
A technical check-up once or twice a year helps prolong the life of the appliance and
guarantees better operation.
Make sure that assistance is carried out solely and exclusively by qualified personnel.
For any spare parts orders or for any information about the appliance, always mention the
serial number and model (data indicated on the "technical data" plate at the rear of the oven).
2. General warnings
Very important!: keep this instruction book together with the appliance for future
consultation.
These warnings were drafted for your safety and for that of others. Please read them
carefully before installing or using the appliance:
-If, on receipt of the goods, the packaging is damaged, write the following on the delivery
note: “I REVERSE THE RIGHT TO CONTROL THE GOODS”, specify the damage and get
the driver to sign in acceptance; send a claim in writing to the seller within 4 calendar
days from the date of receipt. No claim shall be accepted after such period.
-The appliance is intended for professional use and must be utilised by qualified personnel
trained to use it.
-Any modification which may be necessary on the electrical system to enable installation
of the appliance, must be carried out solely by competent personnel.
-It is dangerous to modify or attempt to modify the characteristics of this appliance.
-Never clean the appliance with direct water jets, because, if any water enters, it could
limit the machine's safety .
-Before doing any maintenance or cleaning jobs, disconnect the appliance from the
electrical mains and allow it to cool.
-Do not attempt to carry out the periodic controls or any repairs by yourself. Contact the
nearest Service Centre and use only original spare parts.
N.B.: Improper or incorrect use and failure to observe the installation instructions shall release
the manufacture from all responsibility. In this connection, the directives in the "POSITIONING"
paragraph must be strictly observed.

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 7 _
3. Technical specifications
height (feet included) cm 78
width cm 91
Overall dimensions:
depth cm 75
Weight: kg 86
height cm 51.5
width cm 60
Internal dimensions
(effective) of the cooking
compartment: depth cm 45
Volume (effective): dm3139
Tray maximal load: GN 1/1 kg 4
Total load: 6 trays GN 1/1 kg 24
2 Convection heating elements kW 8
Power elements: 2 Convection motor ventilators W 240
Maximum total power: kW 8.4
Class: I (against electric shocks)
Degree of protection
against humidity: IPX0
Power supply voltage: (50 Hz) 220/230V∼380/400V∼2N
Power cable diameter: 3 x 6 mm24 x 2.5 mm2
Type: H07RN-F H07RN-F
The noise level of the appliance in operation is below 70 dB (A).
The "technical data" plate is positioned on the rear panel of the appliance.
4. Instructions for the installer
The following instructions are aimed at the qualified installer, to ensure that he carries out
the installation, adjustment and maintenance operations as correctly as possible and according
to current legal regulations. Any operation must be performed with electrical power cut to the
appliance.
Before using the appliance, carefully remove the special adhesive film protecting the parts in
stainless steel. Do not leave any glue residues on the surfaces. If necessary, remove them at
once, with an appropriate solvent.
Positioning - Position the appliance perfectly horizontally on a table or similar support (the
table or support must be at least 85 cm above the floor). Position it at a distance of not less
than 10 cm from the side and rear walls, to enable natural ventilating air to circulate freely
around it. The appliance is ventilated through specific openings on the metal walls of the outer
housing , and ensures efficiency and long-life. For this reason it is strictly forbidden to obstruct
these ventilation openings, even partially or for short periods. Failure to observe this specific
prohibition releases the manufacturer of the appliance from all responsibility and immediately
voids any guarantee rights for the said appliance, because its constructive conformity has been
voluntarily compromised. Furthermore, the appliance is not suitable for embedding and for
grouped positioning with other identical appliances.
Electrical connection - The appliance must be connected to the electrical mains according to
current legal regulations. Before making the connection, make sure of the following:
-the voltage and frequency values of the power supply system match the values on the
"technical data" plate affixed on the appliance;
-the limiting valve and the system are able to support the appliance's load (see the
"technical data" plate);
-the power supply system has an adequate earth connection according to current legal
regulations;

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 8 _________________________________________________________________________________________
-a single-pole switch with minimum between-contacts aperture of 3 mm, sized to the
load and conforming to current legal regulations, is fitted between the appliance and the
mains in the direct connection to the mains;
-the single-pole switch used for connection is easy to reach when the appliance is
installed;
-the yellow/green earth wire is not interrupted by the switch;
-the power supply, when the appliance is operating, must not deviate from the rated
voltage value by ±10%.
-make sure that after inserting the power supply cord into the terminal block it does not
come into contact with any of the cooking range's hot parts.
Connection to the water mains - The appliance must be fed with softened drinking water,
with hardness from 0.5°F to 5°F (it is obligatory to use a softener to reduce the formation of
lime inside the cooking chamber) and pressure in the range from 150 to 250 kPa (1.5 - 2.5 bar).
Connection to the water mains should be made through the threaded 3/4" solenoid-valve on
the rear of the appliance, fitting in between a mechanical filter and an on/off tap (before you
connect the filter, allow a certain quantity of water to flow out in order to drain any waste from
the pipe).
Water drainage - One drainage tube comes out from the rear of the appliance, to drain the
cooking compartment. You should connect one pipe to the drain tube, with an internal
diameter of 30 mm (DN 30), resistant to vapour temperatures. To prevent choking, make sure
that the pipe is stiff and that it does not have any elbows along the drainage path. Furthermore,
the pipe must be at constant inclination (5% minimum) along its entire length (the length under
consideration is from the drain tube of the appliance to the drainage point and must not exceed
1 meter). The drainage pipe must lead to an open floor-level drain and, to ensure conformity to
current legal regulations on hygiene, it must not come into direct contact with the drainage
point.
Connecting the power cable - To access the terminal board, just remove the appliance's left
side-panel. Loosen the cable gripper and allow the cable to pass through it. Arrange the
conductors so that the earth conductor is the last to detach from its terminal if the cable goes
into a state of faulty traction. Connect the phase conductors to the terminals marked “L1” and
“L2”, connecting the neutral conductor to the terminal marked "N" and the earth conductor to
the terminal marked with the symbol according to the following lay-out:
(this electrical connection lay-out is located near the power supply terminal board ). Tighten the
cable gripper and re-fit the left side-panel of the appliance.
The appliance must be connected to an equipotential system whose efficiency must first be
checked according to current legal regulations.
This connection must be made between different appliances by using the appropriate terminal
marked with the symbol . The equipotential conductor must have a minimum diameter of 10
mm2The equipotential terminal is at the rear of the appliance.
Safety thermal breaker - The appliance has a manually reset safety thermal breaker. It
protects against excessive dangerous over-temperatures which could be accidentally generated
inside the appliance. If the device is tripped, it interrupts electrical power to the appliance and
thus prevents it from operating. To access this device, remove the left side-panel of the
appliance.

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 9 _
5. Use instructions (for the user)
For first use, we advise you to let the appliance to run load-free at maximum temperature for
about one hour. In this way, any unpleasant smells due to thermal insulation and residual work
grease are eliminated.
This appliance must be used solely for the purpose for which it was expressly designed, i.e.
cooking foods in the oven. Any other use is considered unsuitable.
The appliance can be used: for all oven cooking of deserts, pizzas, meat, fish, vegetables, as
well as for gratinating, and for re-conditioning cooled and frozen foods.
When placing food in the cooking compartment, leave a space of at least 40 mm between
pans in order not to over-obstruct air circulation.
Do not use pans with higher than necessary edges: edges are barriers which prevent the
circulation of hot air.
Warm up the oven before every cooking operation to obtain maximum uniformity.
Do not salt foods in the cooking compartment.
6. Residual risks (for the user)
After a cooking operation, open the door cautiously, to avoid a violent outflow of heat which
could cause burns.
While the oven is in operation, pay attention to the hot zones (marked on the appliance) of
its external surfaces.
Place the machine on a bench or similar support, at a height of at least 85 cm from the floor.
The bench or support must be able to support the weight of the machine and house it
correctly.
The appliance contains electrical parts and must never be washed with a jet of water or
steam.
The appliance is electrically connected: before attempting any cleaning operation, cut power
to the appliance.
To prevent incorrect connection of the appliance, the relevant electrical and water
connections are marked by identification plates.
If the internal glass panel of the door has to be cleaned, it must be dismantled with the help
of a second operator: one operator supports the glass panel, while the other unscrews its
securing screws.

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 10 _________________________________________________________________________________________
7. How to use the control panel
1. "Discharge vapour" knob
2. "End of cooking" programming knob
3. Control thermostat knob
4. Automatic humidifier knob
5. Line switch key (ON/OFF Key)
6. "End of cooking" programmer indicator
light
7. Control thermostat indicator light
8. Automatic humidifier indicator light
9. Power line indicator light
Fig. 1 Fig. 2 Fig. 3
Programming cooking time - To run the oven, turn the programmer knob (Fig. 1) in line with
symbol (continuous operation) or in line with the selected cooking time (up to 120 minutes).
In the second case, end of cooking is signalled by the oven switching OFF automatically.
Programming cooking temperature - Turn the knob of the adjustment thermostat (Fig. 2) in
line with the temperature selected for cooking.
Programming vapour quantity - To generate vapour while the oven is in operation (cooking
compartment hot), turn the knob of the automatic humidifier (Fig. 3) in line with the required
value (from 1 to 5). If you turn the knob to position • (OFF) the humidifier will stop operating.
1
2
3
4
5
9
8
7
6

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 11 _
Remember
- If you turn the knob to positions “1” to “4”, the humidifier operates by generating vapour
(water is introduced into the cooking compartment) at automatically adjusted, cyclically
repeated time intervals (The higher the number the higher the humidifier operating time and
thus a higher quantity of vapour is produced).
- If you turn the knob to position "5", automatic control of the humidifier is disabled - it now
operates by continuously introducing water into the cooking compartment (continuous
production of vapour).
- Before beginning to run the automatic humidifier, stabilise the temperature inside the
cooking compartment at a value of at least 150°C KF 981 and 110°C KF 981 UD, order to
optimise vapour production.
Line key (ON/OFF) - To electrically power up the appliance, press the key of the line switch to
"ON". In this state, the oven is ready to operate.
Line indicator light - The green line-indicator light indicates that the oven is electrically
connected to the power supply line.
"End of cooking" programmer indicator light - The programmer orange indicator light
indicate that the oven is operating and that cooking time is active.
Control thermostat indicator light - The control thermostat orange indicator light goes OFF
whenever the programmed temperature is reached inside the cooking compartment. It lights up
again when the thermostat is tripped to re-establish this temperature.
Automatic humidifier indicator light - The green indicator light of the automatic humidifier
indicates that the water solenoid-valve is operating and, therefore, vapour is being produced in
the cooking compartment.
Oven internal light - The light is always on when the oven is operating.
To switch off the oven - Turn OFF the knobs of the "end of cooking" programmer and of the
thermostat and press the line switch key to "OFF". When you have finished using the oven,
shut off the water ON/OFF tap upstream of the appliance and cut out electric power.
8. Oven cooking
For cooking, before putting food in, warm up the oven to the required temperature. When
the oven reaches the temperature, put the food in and check cooking time. Switch off the oven
5 minutes before the theoretical time in order to recover stored heat.
Convection cooking (dry heat) - Operate the oven and turn the thermo state knob to the
desired temperature.
Convection cooking + steam (dry heat + wet heat) - Operate the oven and turn the thermo
state knob to the desired temperature and the humidifier know the desired steam quantity.
De freezing - Operate the oven and turn the thermo state knob and the humidifier knob in
correspondence of position OFF (•).

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 12 _________________________________________________________________________________________
9. Cleaning (WARNING: Cut power to the appliance before every operation)
General cleaning - Clean the oven when it is cold. Wash enamelled parts with lukewarm
water and soap, do not use abrasive products, steel wool, or acids, which could ruin them. To
clean the steel parts, do not use products containing chlorine (sodium hypochlorite, hydrochloric
acid, etc) even if diluted. Use specific off-the-shelf products or a little hot vinegar. Rinse
thoroughly with water and dry with a soft cloth. Clean the glass door of the oven with hot
water only, and do not use rough cloths. Do not allow foods (especially acid foods such as salt,
vinegar, lemon, etc) to stagnate on the stainless steel parts, because they could deteriorate. Do
not wash the appliance with direct jets of water, because if water enters, this could limit the
appliance's safety. Do not use corrosive substances (e.g. hydrochloric acid) to clean the oven' s
support bench.
Cleaning the oven - It is good practice to clean the oven interior at the end of every day of
duty. In this way it will be easier to remove cooking residues, preventing them from burning
when the oven is next used. Clean it accurately with hot water and soap or with the appropriate
off-the-shelf products.
Cleaning the door - The glass panel of the door facing inwards toward cooking compartment
can be cleaned with the same type of degreasing product used to clean the compartment.
Otherwise, you can use normal glass cleaning product (non toxic). A common glass detergent
can be used also to clean the glass panel of the door facing outward. In all cases, you may just
use tepid soapy water. After rinsing, thoroughly dry the glass surface with a soft cloth. If
opaque sections form between the two glass panels of the door, they can be eliminated after
dismantling the internal glass panel. Procedure: unscrew the 4 screws securing the glass panel
(grip, between your thumb and index finger, the knurled ring-nut of the screw and turn it anti-
clockwise). Take great care not to allow the 4 plastic washers to drop - they protect the glass
against direct contact with the metal part of the screw. To facilitate removal of the internal glass
panel, first unscrew the two screws which secure the glass panel to the bottom of the door (the
panel stays hung). To ensure a successful job, we advise you, in any case, to carry it out with the
help of a second operator (one operator supports the glass panel while the other unscrews its
securing screws in complete safety). After you have removed the dirt between the two glass
panels, re-install the interior panel, following the instructions in reverse order.
Cleaning the fans - The fans must be periodically cleaned with specific anti-lime scale
products. All the parts must be carefully cleaned, removing all lime scale deposits. To have
access to the fans remove the fan casing after removing the screws that fix it to the cooking
chamber. When cleaning is complete, replace the casing and screws.
Cleaning the door seal - For hygiene and good operations, it is good practice to clean the
door seal at the end of each day’s work. It should be carefully washed with warm soapy water,
rinsed and dried with a soft cloth. Any incrustations or food deposits must be carefully removed,
without using sharp metal tools which could irreparably damage the seal.

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 13 _
10. Maintenance
General information - A periodic control (at least once a year) of the appliance aids to
guarantee long life and correct operations. Any sort of maintenance work on the appliance
must be done exclusively by technically qualified operators who have been trained in the
maintenance work on this appliance. Before beginning any sort of maintenance work on the
appliance, turn the power supply off (at the magnetothermal safety switch upstream from the
appliance) and let it cool down. Access is gained to the inside components that could require
maintenance work by removing the left side of the appliance.
Changing the lighting lamp in the cooking chamber - The lamp is housed between the two
door glasses; to replace it remove the internal glass as described in the paragraph: “Cleaning
the door”. After removing the internal glass, replace the lamp with another with the same
specifications: 12V 35W 300°C (this is a halogen lamp and should not be touched with your
bare hands).
Changing the door seal - The door seal has a rigid profile with 3 fixing tabs. The profile must
be fitted into the guide on the face of the cooking chamber. The rectangular seal fits perfectly
into the frame of the guide and, therefore, the seal profile fits perfectly onto the face of the
cooking chamber. To change the seal, remove the old one from the guide by pulling hard at the
four corners. Clean any dirt from the guide and introduce the new seal (to make this operation
easier, we advise dampening the seal profile with soapy water).
Resetting the thermal breaker safety device - This device is reached by removing the left side
of the appliance and can be reset by pressing the red key right down (which is marked by a
special adhesive label), which is inside the electric components compartment.

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 14 _________________________________________________________________________________________
Possible faults
Type of fault Cause Corrective action
-Incorrect electric connections to the
mains -Check the mains connection
-No mains voltage - Restore mains voltage
Control panel
completely off (the oven
does not work) -Thermal break safety device tripped -Reset the thermal break safet
y
device
-Door open or ajar - Close the door
Cooking cycle set: the
oven does not work -Damaged magnetic sensor -Contact a qualified technician to
repair the sensor
-Incorrect connection to water
mains
-Check the connection to water
mains
-Cut-off cock closed - Check the cut-off cock
-Blocked water inlet filter - Clean the filter
Automatic humidifier
ON: no steam is
produced in the cooking
chamber -Damaged water inlet solenoid -Contact a qualified technician to
repair the solenoid
-Seal not fitted correctly - Check the seal fitting
-Damaged seal -Contact a qualified technician to
repair the seal
Door closed: steam
comes out of the seal
-Handle prong loosened -Contact a qualified technician to
repair the prong
-One of the motors is blocked or
turns slowly
-Contact a qualified technician to
repair the motor
-The motors do not go into reverse -Contact a qualified technician to
repair the motor
The oven does not cook
evenly
-Heating element not powered or is
damaged
-Contact a qualified technician to
repair the element
-Damaged lamp - Change the lamp
Lighting lamp in the
cooking chamber does
not work -Damaged lamp feeder -Contact a qualified technician to
repair the feeder
-Device damaged -Contact a qualified technician to
repair the feeder
The thermo safety
device turns on in
continuous -Regulating thermo state damaged -Contact a qualified technician to
repair the feeder
11. Technical service
Before leaving the factory, the appliance was completely regulated and tested by expert
specialised personnel to guarantee the best operating results.
All repairs and settings must be performed with utmost care and attention, respecting
national safety regulations in force. Always contact your retailer or our nearest Service Centre,
giving details of the problem, the appliance model and the serial number (on the rating plate on
the rear panel).
For any maintenance the user can contact Tecnoeka by calling the telephone numbers on the
cover or going to www.tecnoeka.com.

_ Electric Oven _ rev. 0 ___________________________________________________________ KF 981 – KF 981 UD_
_________________________________________________________________________________________ page 15 _
12. Informations to the consumers
Further to Directive 2002/96/EC, the symbol of the crossed rubbish skip on
the appliance means that at the end of its life, the product must be
disposed of separately from the other rubbish. The user must hand the
appliance to a specialised waste collection centre for electric and electronic
equipment.
The separate collection of the rubbish and subsequent treatment, recovery and disposal help to
produce other equipment using recycled materials, reducing the negative effects on the
environment and public health, which would be caused by incorrect management of the
rubbish.
Should the user dispose of the product abusively, administrative sanctions would be applied.
13. Wiring layout
WIRING LAYOUT MODD. KF 981 – KF 981 UD
Key
M Power terminal board
IL Power line switch
P "End of cooking" programmer
T1 Safety thermostat
T2 Oven thermostat
U Automatic humidifier
S1 Power line indicator light
S2 Programmer indicator light
S3 Thermostat indicator light
S4 Automatic humidifier indicator light
T Transformer for oven lamp
L Oven lighting lamp
V1-V2 Radial motoventilators
R1-R2 Circular heating elements
E Solenoid-valve for automatic humidifier
B Contactor coil
C1-C2 Capacitors
IM Operating direction reversing element
MI Door microswitch

_ TECNOEKA Srl __________________________________________________________ use and instruction manual _
_ page 16 _________________________________________________________________________________________
14. The Warranty
Your appliance is covered by warranty. The seller will replace or repair (and his decision will be final),
free of charge for the customer, only those parts that are defective due to a manufacturing fault on
condition that, under penalty of forfeiture:
−for domestic equipment, the customer notifies the fault within two months from the date when
he/she discovered it and anyway within 2 years form the date of purchase;
−for professional equipment, the customer notifies the fault within 8 days from the date when
he/she discovered it and anyway within 12 months from the date of purchase,
by registered letter with acknowledgement of receipt and enclosing the invoice or receipt proving the
purchase.
Apart from the case when the customer cannot produce the invoice or receipt proving the purchase or
when the above-mentioned terms are not complied with, the warranty is expressly excluded in the
following cases:
1) faults or breakage caused by the transport;
2) wrong or incorrect installation of the product (for instance because of insufficient draught of the
flue or exhausts) in light of the instructions given in the user’s handbook supplied with the
product;
3) inadequate or abnormal electrical, hydraulic and/or gas supplies;
4) carelessness, negligence or incompetence in using the product in light of the instructions given in
the user’s handbook supplied with the product;
5) use of the product for uses different from the one for which it was built or anyway in a manner
not compliant with the instructions given in the user’s handbook supplied with the product;
6) tampering with the product;
7) adjustments and/or maintenance and/or repairs carried out by unauthorised personnel and/or
with non original spare parts;
8) inadequate or careless maintenance of the product in contrast with the user’s handbook supplied
with the product;
9) damages caused by fire, natural disasters and accident as well as by any cause not attributable to
TECNOEKA SRL.
The warranty explicitly excludes: varnished or enamelled parts, knobs, handles, movable or removable
plastic parts, bulbs, glass parts, refractories and any accessories.
TECNOEKA SRL cannot be held responsible for any damages, either direct or indirect, caused by the
product breaking down or following its non-use.
Any repairs carried out during the warranty do not cause said warranty to be extended or renewed.
Nobody is authorised to modify the terms and conditions of the warranty or to issue new verbal or
written warranties.
The warranty is valid only for appliances installed in the European Union.
Any dispute shall be settled by the competent Court in Padua.
Warning for the Buyer:
1. the cooking appliance is designed only for cooking purposes while the heating appliance is
designed only for heating domestic environments;
2. TECNOEKA S.r.l. does not install the appliances; the seller shall be responsible for any installation
carried out;
3. TECNOEKA S.r.l. cannot be held responsible for any damages, either direct or indirect, to people,
pets or property caused by the appliance breaking down or following its non-use.
The Manufacturer cannot be held responsible for any inaccuracies due to misprints or mistakes in
copying in this handbook. The Manufacturer reserves the right to modify the products as he deems fit,
also in the interest of the user, without affecting the vital characteristics of functionality and safety.