Tee-Zed Dreambaby Nelson F826 User manual

INSTRUCTIONS
Nelson Adjustable
Wood Swing Gate
F826
F829
WARNING
Important: Keep instructions for future reference
Read INSTRUCTIONSthoroughly before assembling and installing gate.
Fits openings between 76-122cm (30 - 48in)
• DO NOT allow space between
bottom of gate and floor to
exceed 7.5cm (3in).
•
Regularly check all fasteners
to be sure they are tight
and secure.
• Do not use the safety gate if
any components are damaged
or missing.
•
The surfaces that the safety
gate is to be fixed to must be
suitable for the purpose and
must be structurally sound.
NOTE: Do not use this gate if
it can’t be installed to wall,
door frames or posts – tightly
and flatly.
• When installing against
drywall, make sure mounting
surface is reinforced with a
wall stud.
• DO NOT install this gate to
hollow walls.
• This safety gate must NOT be
fitted across window openings
and the like.
• Install this gate away
from heaters and other
sources of heat.
•
This gate must NEVER be used
as a pool or pond barrier.
• Gate MUST ALWAYS swing
away from stairs.
Swing Control Mechanism
MUST be used to ensure gate
swings one-direction only.
• If the gate is used at the
bottom of the stairs to prevent
the child from climbing up the
stairs, it must be placed on
the lowest stair.
• If the gate is to be used at the
top of the stairs to prevent the
child from falling down the
stairs, it must not be placed
on any stair below the level of
the top stair.
• To prevent serious injury or death,
securely install gate and use according to
manufacturer's instructions and warnings.
• Never use with a child who is able to open,
climb over or dislodge the gate.
• Never leave child unattended. This product
does not replace proper adult supervision.
• This product is intended for use with
children from 6 - 24 months.
•
Use ONLY on openings between 76cm (30in)
and 122cm (48in) wide; can also fit openings
157cm (61.8in) - 220cm (86.5in) when
joining two Swing Gates.
• Use ONLY with locking mechanism
securely engaged.
• NOTE: Never use without 4-point
mounting hardware.
Complies with Standards: ASTM F1004-13
F826/F829 IM p1-p4 - Nov 2015
WARNING
TOO LOW! NOT LESS than 5 cm (2 in) TOO HIGH! NOT MORE than 7.5 cm (3 in)
WARNING
1

CONTENTS & PARTS
Hardware Bag Contents:
Long Hinge Screws (x8)
Paper Mounting Template (x1)
Hinge Plates (x2)
Latch Housings (x2)
Swing Stop (x1)
#10 x 1.25cm (1/2in) Screws (x2)
Joining Screws (x2)
Gate Panel Parts:
A Slats
B Top Rail
C Bottom Rail
D Latch Mechanism
E Upper & (E2 lower) Latch Housing
F Hinge Brackets
G Gate Hinges
H Gate Panels
X Joining points
C
F
FE2
E
B
DXX
X
X
A
H
H
G
TOOLS REQUIRED:
An electric drill with 3mm (1/8in) drill bit, Phillips screwdriver, pencil, and adhesive tape.
Use a Phillips screwdriver when installing screws.
BEFORE YOU START - IMPORTANT:
You can use this gate at the top or bottom of stairs ONLY if:
• the gate is mounted at the top of a stairwell to prevent the child from falling down
the stairs, it must not be placed on any stair below the level of the top stair.
Swing Control Mechanism MUST be used to ensure gate swings one-direction only.
• the gate is mounted at the bottom of a stairwell to prevent the child from climbing
up the stairs, it must be placed on the lowest stair.
• the gate is mounted into a solid structure, e.g. wooden doorway jamb, solid wood
banister post, or wall stud behind dry wall.
• the gate is installed according to these instructions, using 4-point mounting
hardware and screws provided.
• the stairwell allows the gate to be mounted less than 7.5cm (3in) above the floor.
INSTALLATION
If the gate is used at the
bottom of the stairs to prevent
the child from climbing up the
stairs, it must be placed on
the lowest stair.
If the gate is to be used
at the top of the stairs to
prevent the child from
falling down the stairs,
it must not be placed on
any stair below the level
of the top stair.
Bottom of stairs
Top of stairs
2

DO NOT mount the Hinge Brackets or Latch Housing on to uneven molding or wall base board trim (skirting board),
as the gate will not function properly.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location (mounting on plaster/gyprock
alone is not strong enough and not safe). Do not mount to glass.
DO NOT mount the gate less than 5cm (2in) or more than 7.5cm (3in) above the floor.
Make sure the mounting template is in a straight vertical position.
1. Using adhesive tape, attach the mounting template on the
solid wood surface that you have chosen for the hinged side of
the gate.
2. Drill four 3mm (1/8in) diameter starter holes into the
mounting surface at the crosshatch marks on the template.
3. Remove the template from the wall.
4. Drill each hole to a depth of 5cm (2in).
5. Using Hinge Bracket screws, screw the two Hinge Brackets
“F” into the mounting surface with the tabbed edge down.
Tighten the screws until the Hinge Brackets are securely
fastened to the mounting surface.
6. Simultaneously slide the side of both Gate Hinges “G” down
into both Gate Hinge Brackets “F” until it is securely seated (I).
7.
Squeeze the Latch Mechanism “D” and slide the upper Latch
Housing “E” over the Latch Mechanism until it snaps into place
(II). Also slide Latch Housing “E2” over the bottom gate rail.
8. Swing the gate into the closed position and extend the Gate
Panels by sliding out, until the gate contacts the latch side of
the mounting surface.
9. Make sure that the top of the gate is level with the floor.
Carefully mark the position of the holes for the upper Latch
Housing “E”, using a pencil (III).
10. Swing the gate out of the way.
Remove the upper Latch Housing “E”.
11. Drill holes as in point 4. Using the correct screws, secure the
upper Latch Housing to the mounting surface.
12. With lower Latch Housing “E2” in place on lower gate rail,
slide the Latch Mechanism into Latch Housing until snaps in.
13. Using a pencil, carefully mark the position of the holes of the
lower latch housing.
14. Squeeze Latch Mechanism, open and swing the gate out of the
way. Remove the lower Latch Housing from the rail.
15. Drill holes, repeat points 4 and 5.
16. Test that the gate is securely installed by firmly shaking the
top rail of gate.
NOTE: If there is a skirting board (base board) to which the gate is to be attached, build up
the wall area where top mounts are to be fitted using a piece of timber of equal thickness.
Alternatively remove the skirting board (base board) prior to mounting gate.
INSTALLATION
F
G
I
II
DE
III IV
TO OPEN GATE:
• Squeeze the Latch Mechanism “D” upward to unlock;
• Slide the gate in the direction of the arrow to disengage from
the upper Latch Housing “D” and lower Latch Housing “E2”;
• Swing gate open.
IMPORTANT: The end of the bottom rail “C” is slightly longer than
the top rail “B”. Before attempting to swing the gate open, make
sure the bottom rail is disengaged.
OPERATION
DE
E
B
C
E2
3

FOR EXTRA SECURITY:
The optional swing control mechanism provides
extra security.
The swing control mechanism MUST be used to
prevent the gate from swinging into a hazard
such as over stairs or into a heavy traffic area.
1. Mount the gate according to instructions.
2. Determine the direction you want to prevent
the gate from swinging.
3. Attach the swing control mechanism to the
top rail with the solid surface of the swing
control mechanism toward the direction of
the hazard, i.e. the direction you want to
prevent the gate from swinging.
4. The optional swing control mechanism
should not be used in place of the latching
mechanisms.
Always keep the latching mechanism securely
engaged when using the gate. Remove the
gate from opening when not in use.
OPTIONAL SWING CONTROL
JOINING SWING GATES
• Wash gate with mild soap and warm water and dry thoroughly before using.
• Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth.
Never clean with abrasive, ammonia based, bleach based or spirit type cleaners.
• An occasional drop of vegetable oil may reduce wear and tear on moving parts.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
CARE & MAINTENANCE
#10 x 1.25 cm (1/2in)
Screws (x2)
Timber gate with metal and plastic parts.
Plastic parts: Nylon & Polyoxymethylene (POM) materials.
157 - 220cm
(61.8 - 86.5in)
130.5 – 175cm
(51.25- 68.75in)
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to statutory
consumer guarantees and does not seek to exclude or limit them. These
guarantees include that Tee-Zed’s products are of acceptable quality.
This Tee-Zed product is for the specific purpose detailed in the
instructions and packaging and Tee-Zed considers use outside of that
purpose to be abnormal use. To the maximum extent permitted by law,
Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in
accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
Dreambaby
®
products by
Made in Jiaxing, China. ©2015 Tee-Zed Products Pty Ltd
COMPOSITION
Tee-Zed Products Pty Ltd,
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: [phone]
[e-mail]
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre, Auckland
New Zealand Tel: [phone]
[e-mail]
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: [phone]
[e-mail]
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
www.youtube.com/dreambabytv
www.facebook.com/dreambabysafety
www.twitter.com/dreambabysafety
4