TeeJet Technologies CL220 User manual

SETTING INITIAL GUIDELINE (CONTINUED)
If the Mark A button was pressed inadvertently
and a Point A was created, it can be released by
pressing the Mark A-B button followed by the
Decrease button.
GUIDANCE MODE
Press the Guidance Mode button to select Straight
or Curved A-B Guidance. View the bottom left of the
display window to see the Guidance mode selected.
STRAIGHT A-B MODE provides straight line
guidance between two reference points (Points A
and B).
CURVED A/B MODE provides curved guidance
between two reference points (Points A and B). All
swaths are identical to the path driven on the rst
pass between Points A and B.
A+ NUDGE FEATURE
At any time after a guideline is created, the guidance line can be
shifted to the current vehicle position by pressing the Mark A-B
button followed by the Increase button. The heading (and shape,
if in Curved Guidance mode) of the original guideline is maintained,
but the A-B line is shifted to the vehicle’s present location.
INSTALLATION
The CenterLine®220 is equipped with three cables: the attached
Power/GPS Speed cable, the Antenna cable, and the Power Adapter
cable.
POWER/GPS SPEED CABLE - The CL220 should be connected
to a clean cigarette lighter receptacle for power. As an option, the
CL220 can be connected to any controller or monitor that supports a
radar speed input. When connected to the radar speed input of the
monitor or controller, the CL220 will be powered by the controller and
will provide a radar-like speed signal to that device.
GPS ANTENNA AND CABLE - The antenna is magnetic, so for metal
vehicles, position the antenna in the center of the vehicle at the high-
est point. For non-metal vehicles, a metal plate with adhesive strips
has been included in the kit for easy mounting and installation. It is
STRONGLY recommended to use this metal plate underneath the
antenna as it will also boost signal strength. Once the antenna has
been positioned, route the antenna cable carefully to avoid damage.
Attach it to the threaded connector on the back of the CL220.
- Connect to cigarette lighter
with the power adapter cable.
or
- Connect directly to radar speed
input of a compatible controller
(refer to CL220 Providing Speed Signal
on reverse)
Press suction cup to mounting surface and ro-
tate locking arms clockwise to the ON position.
Press the Power button to power up the CL220. The CL220 start-
up screen will appear until a GPS signal is acquired. Press the Power
button again to power down the console.
BRIGHTNESS/CONTRAST
Press the Brightness or Contrast buttons.
Use the Increase and Decrease buttons
to make adjustments. To invert the colors on the
display, press and hold the Contrast button for
3 seconds.
SWATH WIDTH
Press the Swath Width button. Use the In-
crease and Decrease buttons to make ad-
justments to the swath width.
The swath width value is displayed in feet. The
swath width measurement displayed will be used
until changed.
SETTING THE INITIAL GUIDELINE
At the desired location for guidance to begin,
press the Mark A-B button. Point A will be
marked. The display will then change to Mark B.
Travel to the location for Point B to be marked.
Press the Mark A-B button to mark Point B.
The CL220 will begin providing guidance with the
lightbar and data display.
A
B
APoint
BPoint
CHANGE PAGE
Use the Change Page button to alternate be-
tween the Data Page and the Map Page.
RETURN TO POINT
Press the Return To Point button to store a loca-
tion in which to return at a later time. A dot will ap-
pear on the bottom of the display, indicating that a
position has been stored.
To locate the point, press the Return To Point
button again and begin navigating toward the point
as indicated on the display. To exit Return To Point,
press the Return To Point button again. Use the
Change Page button to switch between the Re-
turn To Point display screens.
Data Page
Map Page
The dashed lines
represent
adjacent swaths
The arrow points in
the direction of the
marked point
A line is drawn between
the marked point and the
vehicle
The vehicle is at the
marked point location
Position the GPS antenna in the center
of the vehicle at the highest point with
a clear view of the sky. If the tractor is
non-metal, mount the metal plate in the
center of the vehicle at the highest point
with the adhesive strips and place the
antenna on the plate. Route the antenna
cable carefully to avoid damage.
APoint
BPoint
Straight A-B Guidance
Straight A-B Guidance
Curved A-B Guidance
Curved A-B Guidance
Speed/P ower
Cable
Connectto
+12v Only
PowerCable
45-05478
+12v Only
PowerCable
45-054 58
DC:xx/ xx/xx
POWERCABLE
45-05471
DC: XXXX
VecroTM Strips
60-10081
Antenna Mounting
Plate
65-05179
GPS Antenna
GPS Speed/Power Cable
45-05478 Cable, Battery Power
45-05471 Cable, Adapter Weather-Pack
*45-05458 Cable, Lighter Adapter
*included in kit 90-02399
Antenna
Metal plate
CENTERLINE 220 SETUP AND OPERATIONS
GPS
GPS
DGPS
10
9.4
5.8 MPH
Power
Lightbar
Brightness
Contrast
GPS Status
Lights
Change
Page
Display
Increase/
Decrease
Guidance
Mode
Swath Width
Return to
Point
Mark A/B
guidance mode selected
GPS
GPS
DGPS
GPS
GPS
DGPS
GPS
GPS
DGPS lights illuminated on the right of the
lightbar require a steering adjust-
ment to the left
lights illuminated on the left of the
lightbar require a steering adjust-
ment to the right
Center
3.0 ft (.9 m)
4.5 ft (1.4 m)
6.0 ft (1.8 m)
7.5 ft (2.3 m)
1.5 ft (.45 m)
Distance to point

CENTERLINE 220 PROVIDING SPEED SIGNAL
The CL220 can be connected to any controller or monitor that sup-
ports radar speed input. When connected to the radar speed input of
the monitor or controller, the CL220 may be powered by the control-
ler and will provide a radar-like speed signal to that device.
Speed adapter cable required: P/N 45-20042
Radar Speed Calibration # for TeeJet Controls: 914
No adapter required.
Radar Speed Calibration # for Mid-Tech Controls: 1000
Speed adapter cable required: P/N 45-20042
Radar Speed Calibration # for 70 Series monitors: 9140
Speed adapter cable required: P/N 45-05508
Radar Speed Calibration # for Raven Controls: 730
CURVED A-B MODE DETAILED DESCRIPTION
Curved A-B mode provides curved guidance between two refer-
ence points - Points A and B. All swaths are identical to the path
driven on the rst pass between the initial Points A and B. Guid-
ance beyond Points A and B will result in Straight Line Guidance.
To optimize curved guidance performance, begin product applica-
tion on the longest side of the eld and work toward the shorter
side. The following example illustrates the areas that will NOT be
covered by curved guidance when starting on the short side.
Mark A
Mark B
no curved guidance
no curved guidance
Straight A-B Guidance
Straight A-B Guidance
Curved A-B Guidance
Curved A-B Guidance
1801 Business Park Drive
Springeld, Illinois 62704 USA
Tel [phone]
Fax [phone]
www.teejet.com
98-01162 R4
TECHNICAL SPECIFICATIONS
Electrical:
- Operating temperature -4oF to +158oF/-20oC to +70oC
- Operating voltage +9VDC to +16VDC
- Operating current < 500mA
Dimensions:
- Enclosure W: 7.125” H: 5.125” D: 1.875”
W: 180.9 mm H: 130.1mm D: 47.6mm
- Display W: 1.42” H: 2.70:
W: 36.0 mm H: 68.5 mm